Telemetry
Telemetry is the collection of measurements or other data at remote or inaccessible points and their automatic transmission to receiving equipment for monitoring. Wikipedia
See Also: Test Transmitters, Telematics
-
product
Rechargeable Battery Telemetry Systems
2100R Series
Advanced Telemetrics International
Offers more performance and features while providing solutions to common shaft mounted obstacles. Separate but simultaneous data and status signals allow a variety of control functions independent of the high quality data stream ATi is known for. Battery power means lower noise floors, more versatile installations, no active power generation or tuning.
-
product
Telemetry System for Electrics
HTS-SS Blue
Our HTS-SS Blue sensor station system provides comprehensive telemetry information about your electric-powered aircraft and is compatible with the HTS-Volt, HTS-GPS, HTS-TEMP, HTS-ORPM, HTS-MRPM, HTS-C200 and HTS-C50 suite of sensors.
-
product
Datalogger
iLOGPlus
Infinite Industrial Informatics Lt
iLOGPlus RTU/Data Loggers are internet enabled devices, specially suited for remote data acquisition, distributed telemetry and remote control. The units act as master devices and send alerts and data files on their own via FTP, email and SMS. All types carry a built-in TCP/IP webserver with live webpages that can be accessed by any Internet browser application. They accept and serve TCP and SMS commands for interactive operation in a SCADA system.Analog inputs and digital I/O are expandable by means of I/O expansion modules, plugging on a serial I/O expansion bus.
-
product
Telemetry Tracking and Command
TT&C
L3 Cincinnati Electronics (L3 CE) offers a variety of TT&C Receivers and Transmitters for various mission requirements. L3 CE can customize any of the products listed below to fit any mission command and telemetry needs.
-
product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
product
CPCI Or PXI PCM & ARINC 717 Board
MS 1703
*Bus Interface - PXI / CPCI Bus*Microprocessor and FPGA design based Board*One Channel ARINC 717 Transmitter and Receiver*Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals*Used to test all types of PCM based telemetry equipments*Configurable output signals format (parity, word length, Minor, Major frame, Bit position)*User can configure the words and there positions in the frame*The word can be either a square / triangle wave data or constant data*1 MB Shared Memory for Data Storage*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
Global Buoy Monitoring/tracking Beacon With Iridium SBD Telemetry.
Globeacon™ GPS Tracker
Strap the Globeacon to a buoy to monitor its location anywhere in the world using the Iridium SBD satellite telemetry system. Real-time status and data available via the web, text messaging, or insert directly into your own application using our API interface.
-
product
Telemetry Voice Announcing System
HTS-Voice
Designed to fit on the handle of all Hitec radios, this system audibly provides telemetry data via speakers or earphones.
-
product
Displacement Transducers
Procter & Chester Measurements Ltd
Pressure: Measures gas or liquid pressure. Pressure is an expression of the force required to stop a fluid from expanding. The transducer generates a signal from the pressure imposed upon it. Torque: Measures the torque (or twisting motion) on a static or rotating system. The static torque element has little movement and therefore more economic to manufacture and purchase. Rotary or dynamic torque is more complicated as the signal needs to be transferred using slip rings, wireless telemetry or rotary transformers/inductance technology so that the strain gauged shaft can continuously rotate. Displacement: Measures distance. The displacement transducers that PCM offer are slightly different to standard units. They have a strain gauge/wheatstone bridge. The benefit here is that if the customer has existing electronics that uses strain gauge/load cell technology, they can use them with these sensors.
-
product
TW-3.0 Multi Logger Software
The TW-3.0 Multi Logger Software from DLM is designed to complement DLM’s TW-3.0-Trange of products. It is used for monitoring and logging data for up to 24 TW-3.0-T LoadCells including Wireless Compressive Load Cells, Telemetry Tensile Links, and TelemetryLoad Shackles.
-
product
Prop Shaft Torque Measurement Systems
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
product
Telemetry Systems
For Automotive, Aerospace, Marine, Motor & Generator Health, Energy, Power Plant, and Industrial Applications.
-
product
High Density Switching & Distribution Unit Linker System
LS1601A
Universal Switching Corporation
For Communication, Telemetry, ATE and Broadcast Installations. Continuing to expand our distribution product offerings, the new LS1601A offers a fresh new alternative to system engineers. The 3RU rack mountable unit has a unique "open window" front panel design that allows up to sixteen plug-in modules to be installed with both forward and rear facing connectors, controls, and indicators. For control and monitor, a plug-in LXI certified 10/100 Ethernet module can be installed
-
product
Telemetry Tensile Link
TL-3.0
The TL-3.0 is a third generation Telemetry Tensile Link load cell. A light weight wireless tension measuring unit that combines a high level of performance with a robust design for harsh environments.
-
product
Airborne Receiver
MS 2015
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
product
Receivers - Special Application
Our specialty receivers are a diverse mix, including monitoring receivers for audio engineering applications, marine receivers, sonobuoy telemetry receivers and phase-coherent receivers.
-
product
MIL-STD-1553 Data Acquisition Module for Ethernet Networks
eDAQ-1553
Avionics Interface Technologies
One or two dual redundant MIL-STD-1553 bus interfaces - Transformer and Direct bus coupling supported - Two 10/100/1000 Mbit/s Ethernet LAN Interfaces - Streams MIL-STD-1553 bus data in standard IRIG 106 Chapter 10 format. - Compatible with 3rd party recorders and telemetry tools - All captured MIL-STD-1553 bus data provided with timestamps - Full error injection & detection capabilities - Works with AIT’s Flight Simulyzer™ GUI Analyzer/Simulator software
-
product
Narrow-band UHF/VHF Radios
UHF and VHF radio products are used in narrowband RF (radio-frequency) telemetry systems. These systems consist of a radio modem and low-powered transceiver at the remote station(s), and a transceiver connected to a modem or base station at the computer site. Up to 254 stations can be interrogated over a single UHF or VHF frequency.
-
product
Telemetry Antennas
Communications & Power Industries
CPI SAT is a multinational manufacturer of high-performance, highly engineered antenna systems used for critical satellite communications, telemetry, tracking and control (TT&C), general telemetry, earth observation (EO), radar, electronic warfare, search and rescue and other specialty applications. Offering advanced antenna systems for land, air and sea, with a full range of solutions and capabilities to meet any military requirement, and its Orbital Systems operations design and manufacture antenna systems that meet the high performance, accuracy, and high reliability needs of demanding satellite tracking applications and mission-critical uplink and downlink applications.
-
product
Telemetry Repeater
TRT400
Systems Engineering & Management Company
SEMCO's TRT Telemetry Repeaters provide for reception and re-transmission of telemetry down-links in applications determined by link margin analysis. The TRT unit typically consists of a receive antenna and SEMCO's R100, R200 or R400 Series Receiver that is configured to support the required transmitted frequency bands. The demodulated telemetry signal is then re-transmitted in a different frequency band by a 5, 10 or 20 watt transmitter and antenna installed in the TRT Repeater. The TRT is housed in a ruggedized, portable enclosure and is designed to withstand harsh outdoor environments
-
product
LTE Networks
PBE offers secure and reliable wireless solutions for critical mining and tunnel construction operations. Complete end-to-end private LTE networks provide unified infrastructure for underground applications with different QoS, bandwidth and latency requirements.PBE private LTE allows customization of the capabilities of public cellular LTE networks and scale it according to the size and requirements of the particular mine. P-LTE networks provide both human and machine communications on a single, seamless and extendable network that offers long ranges of propagation. In addition to the standard telemetry (air quality monitoring, ventilation management, pump control, belt control, fire suppression, evacuation alerting stations, etc.) LTE networks provide a gateway for:- Voice Communications (VoLTE, VoIP, Push-to-Talk)- Video Communications- CCTV- Internet Access- LAN Access- Real Time Machine Control- Fleet/Asset Management- Access Control/Localization- Automation- Collision Avoidance- Remote Diagnostics
-
product
Multi-Channel PCM Processing and Recording System with UDP Streaming
LS-68-M
The Lumistar LS-68-M Modular Multi-Channel processing and recording Telemetry Processing System offers an ultra-small, low-cost, high-performance, multi-channel COTS solution for PCM data synchronization, decommutation and simulation applications. Building on the legacy of the Lumistar LS-45, LS-50, LS-55 and LS70 series of products, the LS-68-M enhances the feature sets of each of these product lines and supplies them in a format requiring no hardware drivers in an “OS-less” environment. The LS-68-M utilizes a highspeed Gigabit Ethernet interface for primary controls and data streaming.
-
product
Radio Telemetry
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis. Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics. Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
-
product
Bus Management Test System
Solution to test redundant Architecture of BMUComprehensive test system performing tests of > 3000 I/O's Special test circuits using hybrid / ceramic components to operate in Thermovac chamber Tests various subsystem functionalities like, AOCS, Sensor Electronics, Telemetry, Tele-command with Self test and application test software
-
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
product
Current Sensors
MCx1101 Family
Power architects are continually asked to push the boundaries for system efficiency, response time, small size, and low cost in new power system designs. Most modern designs require current sensors to help implement the complicated control, telemetry, and protection circuitry essential in meeting these difficult design goals.
-
product
Telemetry Receivers
Advanced Telemetrics International
ATi manufactures a wide range of telemetry receivers for use with our systems. Single channel, multi-channel and multiplexing telemetry receivers are available in various configurations, depending on the application.
-
product
Portable Telemetry Systems
Lumistar’s portable receivers and test transmitters take the state of the art technology found in the PCI receivers and simulators and install it into a hand held units. Our luggable Telemetry Systems can be configured using our card level products into unique custom solutions.
-
product
Fuel Moisture and Fuel Temperature Sensors
Fuel moisture and fuel temperature sensors emulate and measure the moisture content and temperature of similarly sized twigs on the forest floor. The sensors are typically used as part of larger systems, such as fire weather stations with dataloggers and telemetry capability, to remotely assess changing fuel conditions and potential fire hazards.
-
product
Large Telemetry Compressive Load Cell
TC-3.0-LG
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
