Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
Environmental Testing Services
INO offers a range of environmental testing services to help you perform prototype qualification and durability testing in the fieldtwo critical steps in the development of a reliable and profitable product. Our services can be used in a variety of settings, including quality control, land, sea, and air transportation simulations, accelerated aging simulations, resonance frequency searches, specifications and standards compliance testing and product qualification testing for standards such as MIL-STD, FOTP, and ESA.
-
product
Wafer ESD Tester lineup
Hanwa Electronic Ind. Co.,Ltd.
◆Correspond to 300mm Wafer. This tester can measure LED or the large sizes Wafer, such as a system LSI. And Zap of HBM/MM can be performed. The Automatic destructive judging by V/I measurement can also be performed after Zap.◆Waveform guarantee in Zap needles. HED-W5100D carries out the calibration before shipment in the place of Zap needles. Therefore, Correlation of the Result of a Package Device becomes clear easily.◆Correspondence to Standards This Tester corresponds to the Standard of JEITA...show more -
product
Confocal Raman Microscope
LabRAM HR Evolution
The LabRAM HR Evolution Raman microscopes are ideally suited for both micro and macro measurements, and offer advanced confocal imaging capabilities in 2D and 3D. The true confocal Raman microscope enables the most detailed images and analyses to be obtained with speed and confidence. With guaranteed high performance and intuitive simplicity, the LabRAM HR Evolution is the ultimate instrument for Raman spectroscopy. They are widely used for standard Raman analysis, PhotoLuminescence (PL), Tip Enhanced Raman Spectroscopy (TERS) and other hybrid methods.
-
product
Low Profile PCI Express 8-Port
7803e
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550...show more -
product
Oxygen Analyser
Walsn occupies a leading position in the field of combustion efficiency monitoring and oxygen analysis technology. Our in-line zirconium oxide oxygen analyzers have long been established as industry standards.
-
product
High Density Plasma Etching System for 200mm substrates
Model DRIE-1200-LL-ICP
Single process chamber for high rate plasma etching of 200mm wafers. Loadlocked. Stainless steel construction. Capabilities of smaller, multiple wafer throughput. Substrate materials include (but are not limited to) silicon, silicon oxynitrides, SiC, SiGe, Aluminum, and III-V compounds including GaAs, GaN, GaP, and InP. Stable plasma generation capabilities to below 1 mTorr. Five, Six, or Eight gas mass flow controllers are standard. Expanded or reduced numbers are available upon request.
-
product
Standard 1.00 (28.30) - 5.40 (153.00) Battery Probe
BIP-10
Current Rating (Amps): 5Average Probe Resistance (mOhm): 30Resistance Remark: Probe Resistance Steel: 30 mOhms, Gold plated: 100 mOhmsTest Center (mil): 260Test Center (mm): 6.60Full Travel (mil): 157Full Travel (mm): 4.00Recommended Travel (mil): 126Recommended Travel (mm): 3.20Overall Length (mil): 591Overall Length (mm): 15.00
-
product
Single Channel DOCSIS 3.1 in Realtime
SFD DOCSIS
The R&S®SFD generates a DOCSIS 3.1 channel in realtime with flexible setting of the level, frequency, constellation and all other parameters according the DOCSIS 3.1 standard. The R&S®SFD can alternatively generate a digital realtime modulated TV signal according the J83A/B/C specification. The content can be fed in via IP or internally generated by the R&S®SFD.
-
product
Magnetic Stripe Test Cards
Test Limit Cards (and tickets) are nominally encoded to ISO standards BUT WITH specific parameters deliberately set to predetermined levels, which can be inside or outside the ISO limits. The Test Limit Cards are designed for use by Test\Inspection Departments, Field Service Engineers, Reader \ Encoder Development Engineers to check and confirm proper operation of magnetic stripe reading equipment (e.g. ATMs and POS).
-
product
Complete Field Meter Site Testing Solution
7 Series
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
product
PXIe-6569, PXI FlexRIO Digital I/O Module
787281-01
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
product
Saluki SFS-2000 Fusion Splicer (4 motors)
SFS-2000 series is the new standard 4 motors fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, makes it very popular and hot.* 7s fast splicing, 14s highly efficient heating* 320/88 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 220 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
product
Turbidity / Chlorine
Turbidity (undissolved solids) is an important measure of water quality in environmental testing, wastewater, petrochemical, beverage industry, and electroplating. Water chlorination is the process of adding chlorine (Cl2) to water as a method of water purification to make it fit for human consumption as drinking water. Sper Scientific offers Turbidity and Chlorine meters that meet the EPA method 330.5 for waste water and standard method 4500-CI G for drinking water and the ISO 7027 standards.
-
product
Laser Diode Modules: 635nm-660nm Visible Wavlength, Elliptical Beam
The Optoelectronics Company Ltd
Custom lasing wavelengths, from 405 nm to 852 nm, output power options and laser engraving are available to your specifications. Both standard and custom configurations provide OEMs, end-users and systems integrators with complete cost-effective laser solutions.
-
product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1B-4
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
PXI 3x3 20GHz Matrix
40-787-528-3X3
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Standard 1.10 (31.00) - 3.85 (109.00) General Purpose Probe
HPA-64-3
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 375Overall Length (mm): 9.53Overall Length Remark: Exact length depends on selected tip: Tip 1,4, 7: 0,375″; Tip 2,3,9,10: 0,365″; Tip 8: 0,385″
-
product
BRIC™ - Large PXI Matrix Modules
High Density Packaging and Integrated BackplanesWith Pickering's BRIC Large PXI Matrix Modules, the use of high density packaging and integrated backplanes enables a large matrix to be implemented with no user configuration or special matrix expansion kits. These matrices use thru-hole mechanical relays (not surface mount) and can be serviced using standard de-soldering tools simplifying repair and reducing down time. Our BRIC's integrated design ensures high matrix performance with high signal bandwidth and fewer system implementation errors.
-
product
Gauge Type T Thermocouple Wire
W-TW-40
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Dual Wide Range Power Monitor
LTC2992
The LTC®2992 is a rail-to-rail system monitor that measures current, voltage, and power of two supplies. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The voltage measurement range of 0V to 100V is independent of the input supply. Two ADCs simultaneously measure each supply’s current. A third ADC monitors the input voltages and four auxiliary external voltages. Each supply’s current and power is added for total system consumption. Minimum ...show more -
product
Standard Payload 300mm and 450mm Wafer Transport Tool
G-Rex3™
The G-Rex3™ robotic system offers a small footprint, optimal throughput, reliability and serviceability in a cost effective package. It features innovative patent-pending designs, advanced control approaches and EZTeach technologies resulting in improved performance and reliability. The G-Rex3™ is a simplified low-mass design with fewer parts and moving components. The result is improved dynamics leading to higher acceleration and speed.
-
product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe
LFRE-1Z-4
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
SparkFun Shift Register Breakout
74HC595
This is a breakout for the SOIC version of the 74HC595 shift register IC. Clock in data and latch it to free up IO pins on your micro. All pins from the IC are broken out to standard 0.1" spaced headers. The Serial in and out pins are on opposite sides of the board with the remaining pins carried over so that multiple shift register boards can be chained together.
-
product
Application Specific LC Systems
Mycotoxin Screening System
Mycotoxin (mold toxin) is a generic term for metabolites produced by molds on food products that are hazardous to human and animal health. To improve food safety, food processors have been inspecting ingredients for the presence of such mycotoxins. In only 14 minutes, this mycotoxin screening system is able to detect the presence of 10 mycotoxin components with high sensitivity at concentration levels specifled by EU standards, which are the strictest in the world. Furthermore, because the system does not involve a sample derivatization process, samples can be measured much more efficiently.
-
product
3U Processor Board
CP32107
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® 4th Generation Core™ and Celeron® i7/i5/i3 processors, CP32107 is a high-performance 3U 8HP CPCI PlusIO SBC with up to 4x2.4GHz and 8 threads CPU. For better heat-dissipation, CP32107 is equipped with a noiseless fan that has adjustable rotational speed.CP32107 is provided with rich front and rear I/O interfaces, including 2x USB3.0 for peripheral, 2x GbE (through M12 Connector) for LAN, 1x Display Port supporting 3840x2160 output on front; 2x SATA III, 2x GbE, 4x USB2.0, 2x RS232/422/485 on rear. The rear is compliant with PlusIO Standard, and supports 3 x1 PCIe Gen2.0 interfaces. Besides, mSATA or CFast disk can be installed on CP32107.
-
product
Gas Leak Detector
GSD600
The Amprobe GSD600 Gas Leak Detector is a fast responding gas leak detector for methane and propane gas. The meter emits a frequency tone when gas is detected. The frequency of the beep coincides with the concentration of the gas. The LEDs display the level of gas present in an area or room. Pinpoint gas leaks for closed piping systems. Use the mute function in quiet work areas and utilize the LED displays. Or a standard earphone jack for hearing the meter in loud environments.
-
product
Ultrasonic thickness gauge
The frequency range of sound that can be heard by the human ear is about 20Hz to 20KHz, and sound waves with higher frequencies are called ultrasonic waves. In general ultrasonic flaw detection equipment, 5MHz is often used in the range of 1MHz to 20MHz as standard.
-
product
DC Power Supply With Scope, Arbitrary Waveform Generator, And Automotive Application Features Bundle
E36154AGVX
The Keysight E36154AGVX consists of a Keysight E36154A DC power supply, a Keysight E36150ADVU Scope View and arbitrary waveform generation (AWG) capabilities, and a Keysight E36150ATMU Automotive Standards Testing Capabilities with Enhanced Programming Speed, ISO Preset Library, Playback Simulation and E-Logging features. The E36154A includes single-output and auto-range capabilities, 30V, 80 A, 800 W, and LAN and USB interfaces.
-
product
USB Modular Source Measure Unit
U2722A
The U2722A USB Modular Source Measure Unit is a 3-channel 20V/120mA that can operate in a 4-quadrant operation. The channels could be connected in series or in parallel to achieve up to 60 V/360 mA. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
