Showing results: 6376 - 6390 of 6631 items found.
-
ICS Electronics
ICS's Model 9099 Ethernet to Modbus RTU Interface is a small Minibox™ Ethernet Modbus Converter that converts Modbus TCP/IP, VXI-11 and Raw Socket to control Modbus RTU Slave Devices. The Model 9099 does not require special drivers and is compatible with the following systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX, Windows 2K or later and Modbus capable PLCs. ICS's 9099 uses VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
FMC431 -
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
ICS Electronics
ICS's Model 9065 Ethernet Gateway is an Ethernet to GPIB Controller that connects easily to your computer's Ethernet port, company network or to the Internet to control GPIB instruments. The Model 9065 is VXI-11 compliant, does not require special drivers and is compatible with the following systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. ICS's 9065 uses VXI-11 RPC calls for secure communication with virtually any computer. Eliminates the need for special drivers. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product.
-
ExQ -
Hiden Analytical Ltd.
The Hiden ExQ quantitative gas analyser is a new multi-featured and compact mass spectrometer system providing continuous on-line analysis of dynamic gas streams at pressures from sub-atmospheric up to 30 bar, the fully integrated system now being configurable both for benchtop and for rack-mounting operation. Connection to the process is via a flexible heated inert capillary line with a sample consumption rate less than 10 mL/minute and a response time of less than 300 milliseconds at pressures near atmosphere. The comprehensive range of process interface options enables adaptation of the system to accommodate analysis of up to 16 individual process streams, and adaptors are available for direct connection of the system to most standard TGA/TA instruments. External process data, sample temperature or mass for example, can be imported for combined integration and presentation with the mass spectral data.
-
Ceres T 1280 Series -
Xenics
The Ceres T 1280 series is based upon the Dione 1280 OEM thermal imaging core with 1280×1024 pixels and 12 µm pixel pitch and NETD of less than 50 mK. The camera offers superior on-board thermographic performance (accuracy, stability) in the temperature range up to 400 °C.The Ceres T 1280 camera outputs full frame images at 60 Hz via either a CameraLink or at 45 Hz via GigE Vision interface – all GenICam compliant.The compact size and excellent thermographic stability and accuracy, and GenICam compliant interfacing allow for easy integration in demanding industrial thermography applications.The camera offers one standard option of lens and thermal calibration pack.Benefits & Features• Compact and high-resolution• Superior on-board thermographic performance (stability, accuracy)• GenICam compliant• Uncooled operation
-
National Technical Systems
NTS operates some of the largest and most accurate sand and dust testing chambers available in the industry. We can accommodate parts in excess of 8 ft3 (0.25 m3) and comply with the requirements of various regulatory standards. While sand or dust circulate at up to 40 mph (65 kph) we can modify the test according to your special requirements, including running at temperatures of up to +200°F (+95°C). A calibrated “hopper” which assures that an adequate amount of contaminant is entering into circulation manages the input to the chambers. In addition to measured inputs, NTS employs an electronic beam, which determines that there is the right mixture of sand or dust and air in the test medium at any given time. This enables our technicians to adjust for loss in real time, and make corrections to ensure that the test article is exposed to the harmful particulate matter for the requisite amount of time.
-
ACMAS Technologies Pvt. Ltd.
The extremely accelerated stress environment is defined by high temperature, high humidity and high pressure. WEIBER provides humidity resistance evaluation test for electronics components through customized Extremely Accelerated Stress Test Chamber. This chamber provides high performance test in minimal amount of time according to international IEC 60068-2-66 standard. This chamber also known as Accelerated Stress Test Chamber, Halt and Hass Test Chamber, Halt Test Chamber and Hass Test Chamber.This chamber reduces the time taken for humidity testing in electronic components. 2 types of tests saturated and unsaturated extremely accelerated stress test can be performed. In saturated test the temperature is maintained at 1210C at 100%RH, and for unsaturated temperature of 110, 120, 1300C is maintained at 85%RH. Normally for electronic components unsaturated type test is done.
-
68G6 -
North Atlantic Industries
The 68G6 is a SOSA™-Aligned 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. In addition to the standard expansion plane (EP) PCIe and control plane (CP) Ethernet control interfaces, the 68G6 facilitates convenient external access to supported NAI PCIe function modules through its 1 x1 PCIe interface, enabling seamless expansion of host SBC functions for enhanced project solutions, while also offering external access to supported NAI FMx modules via a SATA II interface. The 68G6 is on NAI’s certifiable product development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G6 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.
-
RF-LiveSim -
TestTree
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
SL1800A Series -
Keysight Technologies
Keysight's SL1800A Scienlab Regenerative DC Emulator - High-Power Series enables users to emulate the large batteries in electric vehicles. The bidirectional power flow allows emulation of both power sourcing applications, such as traction inverter test, as well as power-absorbing (sinking) applications, such as EV charging. Being regenerative, the power absorbed is delivered back to the grid, saving on energy and cooling costs. The SL1800A Series is fully integrated with the SL1040A Scienlab Charging Discovery System. The SL1093A Scienlab Charging Discover Software fully automates DC charging applications to many different test standards. With bi-directionality, integrated DC voltage and current controllers, high dynamics, and its regenerative energy feedback capacity, the Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
ReaXus M1 Class -
Teledyne LABS
The compact M1 Class HPLC Pump consists of single-headed, positive displacement piston pumps that deliver high-performance and precision at an affordable price. Superior to Gear, Diaphragm, and Peristaltic pumps, the M1Class provides greater performance at an equivalent cost to lesser functioning products.Applications include precise chemical metering, dispensing, and specific HPLC separations. Standard fluid path materials are Stainless Steel. With 10 mL/min, 40 mL/min, and 100 mL/min versions, reaching pressures up to 2,500 psi, these pumps capture the majority of typical laboratory fluid transfer applications.Features include interactive keypad control, Pulse Dampener and Outlet Filter, RS-232 Serial and Micro USB 2.0 ports for complete PC control and status, as well as hardware for laboratory stand mounting. Having the smallest possible footprint for a high pressure pump, the M1 Class will easily integrate into any laboratory or industrial environment.
-
ReaXus LS Class -
Teledyne LABS
The reliable ReaXus LS Class consists of single-headed, positive displacement piston pumps incorporating advanced cam designs for very low pulsation.The pumps are ideal for a wide variety of applications, Semi-Prep LC, metering & dispensing, and general laboratory use. Standard fluid path materials are Stainless Steel with PEEK options. Other available features include jacketed heads for temperature controlled processes. With 5 mL/min, 10 mL/min, and 40 mL/min versions available, and pressure capability up to 6,000 psi, these versatile pumps will meet the most demanding applications.Features include automatic pressure compensation, Pulse Dampener, integrated Prime-Purge Valve, interactive keypad control, and complete PC control and status through RS-232 and Micro USB 2.0 ports. The unique LS Class provides the highest performance/cost ratio in a compact package.
-
Vision AutoPlus & Vision AutoFill -
Teledyne LABS
The Vision® AutoPlus™ is a modern upgrade of the popular Hanson legacy AutoPlus™ autosampler. The Vision AutoPlus comes with a choice of 6 or 8 sampling channels, and DissoScan™ (1-bath) or Maximizer™ (up to 3 baths) configurations. Precision syringe pump mechanics, all-inert tubing and valves, and color touchscreen programming with up to 100 protocols are standard on each instrument.The Vision® AutoFill™ is a sample collector designed for seamless integration with the Vision AutoPlus to save space and to provide a 360 degree view for visual monitoring of the collection process.. Vision AutoFill accessories include choice of collection racks with 13 x 100 or 16 x 100 mm test tubes for UV-Vis, 12 x 32 mm vials for HPLC, sample trays with 12 x 32 mm vials for UPLC®, and more.
-
Protocol Manager™ Software -
Teledyne LABS
Teledyne LABS helps ensure the world’s pharmaceuticals are pure, safe, and effective by manufacturing instruments that set the global standard for quality, innovation, and long-term value. Software and software management play a large role in making sure those systems run as they should, and providing results that can be quickly analyzed and acted upon. Hanson software does so effectively and intuitively.Pharmaceutical research, manufacturing, and QC labs running Teledyne LABS Vision and/or CD14 dissolution testers can now manage users, methods, and instruments more efficiently than ever before. Our Protocol Manager software eliminates all instrument-based connectivity and storage limits by connecting your Hanson systems to a centralized protocol database on a Windows® client/server operating system. The spacious, easy-to-use, desktop interface provides drag-and-drop simplicity and increased support for 21 CFR Part 11 compliance.
