Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
PXI 20 Banks 0f 4 Channel 1 Pole MUX
40-615-021-20/4/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
RS-485 Serial I/O
ADAM-4000/4100 Series
The ADAM-4000/ 4100 series featuring rugged industrial-grade cases are specially designed for reliable operation in harsh environments. Built-in microprocessors independently provide intelligent signal conditioning, analog I/O, digital I/O, data display, and RS-485 communication through Modbus RTU protocols.
-
product
PXI-2536, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-36
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
TTL/I2C/SPI* Expansion Kit
OP-SB5GL
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
product
Extenders & Line Drivers
Extenders and Line Drivers enable reliable, long distance signal transmission over coaxial, twisted pair, or fiber optic cabling.
-
product
Vector Tester
PVT360A
The R&S®PVT360A is a VSG/VSA single-box vector tester optimized for FR1 base station, small cell and RFcomponent testing in production and characterization environments. Two independent signal generatorsand analyzers enable fast parallelized measurements. A frequency range of up to 8 GHz, flexible bandwidth configuration and an optional second TRX channel provide the necessary performance and enable flexible adaptation in a small form factor.
-
product
High Power RF Amplifiers
Corry Micronics' line of high power RF amplifiers feature up to 40% efficiency. an extended temperature range of -30 degC to 55 degC for MIL-STD applications, and status monitoring signals that provide diagnostic information.
-
product
WLCSP Probe Heads
Smiths Interconnect offers Wafer Level Chip Scale Package (WLCSP) Probe Heads utilizing spring probe technology which provide high parallelism in test, superior signal integrity and high speed / RF testing capability.
-
product
Process Totalizer (analog input)
Displays and totalizes 0-1 mA, 4-20 mA, or 0-10 V process signals. Square root extraction is standard for flow applications, allowing display of volume from the 4-20 mA signal of a flow transducer with a linear or squared output.
-
product
Matrix Routers
Enjoy seamless matrix switching whatever your source or display. Digital, broadcast or analog: we’ve got it covered with our wide range of solutions. For the ultimate experience go above and beyond with our modular matrix solutions that not only include scaling and format conversion but also the option to seamlessly combine your matrix switching requirements with our class leading Signal Extension solutions.
-
product
Scienlab Measurement And Control Module
SL1063B
The Measurement & Control Module SL1063B is a rack-mount measuring and control module for measuring and switching of digital signals with 16 digital in-/output channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
product
PXI Vector Component Analyzer, 100 kHz to 44 GHz
M9817AS
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
product
USB To RS232 / RS485 / RS422 / TTL / Serial / Ethernet Converters
With our high-quality, high-performance USB to RS232 / RS485 / RS422 / TTL serial and Ethernet converters that use only top-quality chipsets such as FTDI and Silicon Labs, USB signals are converted seamlessly into RS232, RS485, RS422, TTL, serial and Ethernet signals. Pick from our menu of industrial or commercial-grade devices confidently, knowing that you will get nothing but the best from CommFront.
-
product
Low Light USB Camera Board (Color)
See3CAM_CU30 - 3.4 MP
See3CAM_CU30 is a 3.4 MP UVC-compliant Low Light USB camera board based on AR0330 sensor from ON Semiconductor®. This Low Light Board Camera is backward compatible with USB 2.0 and supports compressed MJPEG formats at frame rates equal to USB 3.0. This sensor enables a superior low light performance. It has a dedicated, high-performance Image Signal Processor chip (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images, videos and the MJPEG compressions.
-
product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785596-02
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
product
PXI Single 66x8 Matrix, 1-Pole
40-541-021
The highest density single slot PXI reed relay matrix module on the market today. This range also includes a 132x4 and 33x16 reed relay matrices with 1-pole switching. They are constructed using high reliability sputtered ruthenium reed relays, offering >10e9 operations to give maximum switching confidence with long life and stable contact resistance. Typical applications include signal routing in Functional ATE and data acquisition systems.
-
product
PXI LIN Interface Module
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
GPS Signal Splitter 12 Way, N Type Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS120
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy Type N Female (Jack) Low PIM
-
product
DSP Dual Phase Lock-In Amplifier
SR850
Stanford Research Systems, Inc.
The SR850 is a digital lock-in amplifier based on an innovative DSP (Digital Signal Processing) architecture. The SR850 boasts a number of significant performance advantages over traditional lock-in amplifiers?higher dynamic reserve, lower drift, lower distortion, and dramatically higher phase resolution.
-
product
PXA Signal Analyzer, Multi-touch, 3 Hz to 50 GHz
N9030B
Accelerate innovation in demanding applications with measurement options that range from excellent to exceptionalExtend frequency up to 110 GHz with Keysight smart mixersCapture transient or intermittent signals with real-time spectrum analysisSimplify application-specific testing with X-Series appsPerform deeper troubleshooting with the 89600 VSA software
-
product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
779357-01
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
-
product
Analog/Digital and Network Trace
At iSYSTEM, we realize that embedded systems development requires more than just the insights of the microcontroller/processor. Developers need a holistic view, covering external signals and serial bus messages, or even insights into more than one microcontroller/processor and/or traget system at once.
-
product
IRIG B to NTP/SNTP Converter
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786856-01
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal so...show more -
product
Signal and Spectrum Analyzer
FSW
The high-performance R&S®FSW signal and spectrum analyzer was developed to meet demanding customer requirements. Offering low phase noise, wide analysis bandwidth and straightforward and intuitive operation, the analyzer makes measurements fast and easy.
-
product
Fiber-coupled Polarimeter Module
The A3321A fiber-coupled polarimeter enables real time monitoring of the SOP, DOP, and power of a light signal in fiber.
-
product
Signal, Patchcord, Receiver, 36", QuadraPaddle, 68-Pin Male SCSI
7-124883666-036
Signal, Patchcord, Receiver, 36", QuadraPaddle, 68-Pin Male SCSI.
-
-
product
PXI Dual 2 x 2 Insert/Bypass Switch FC/APC
40-860-022
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
