Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
TiePieSCOPE HS805, 2 Ch, 32MS/ch, 1 GS/s, 250MHz BW, USB Digital Storage Oscilloscope, AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS805
The TiePieSCOPE HS805 is a portable USB oscilloscope that combines a high sampling speed (1 GSamples/s on one channel, 500 MSamples/sec on two channels) with a long record of 32 MiSamples per channel. That allows you to capture long, complex signal patterns at full speed. The 250 MHz high bandwidth ensures that the signals are measured accurately and without distortion.
-
product
Modulation Distortion Up To 13.5 GHz
S930701B
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
USB-5133 , Oscilloscope 50 MHz Bandwidth, 100 MS/s, 2-Channel, 8-Bit USB Oscilloscope Device
780469-02
50 MHz Bandwidth, 100 MS/s, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5133 low-cost oscilloscope device has two channels that sample up to 100 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
product
Up/Down Converters
Over the years, In-Phase Technologies has received many requests for frequency conversion units. Our standard product line of frequency converters includes models that operate from RF though 60 GHz. Many options are available to complement our standard offerings. We also have a series of RF-to-optical converters that allows customers to send RF and microwave signals over fiber optic cables.
-
product
Contrast Sensors
Leuze electronic GmbH + Co. KG
Contrast sensors detect and compare contrasts very precisely through the use of different light sources such as white light, laser-generated red light or RGB light. The detected contrasts marks are then reported to the process with minimal signal jitter. Through the automatic selection of the right transmitter colors, various color or gray value combinations can be reliably detected. Bar graph indicators offer additional ease in making adjustments during manual setup.
-
product
Mixed Signal Oscilloscope
6 Series MSO
Troubleshoot and validate high-speed designs now and into the future with upgradeable bandwidth that starts at 1 GHz and goes up to 8 GHz . Get accurate measurements with low noise and 25 GS/s sample rate per channel -- sample rate does not drop as you turn on channels.
-
product
LTE/LTE-Advanced Analysis Using NI PXI RF Test Instruments
NI-RFmx LTE/LTE-Advanced
Highly optimized RF measurement experiencePerform physical layer analysis on LTE cellular signals including MODACC, ACPR, CHP, OBW, and SEMIncludes support for TDD, FDD, and LTE-Advanced signals specified in 3GPP standards release 12Simple access to advanced measurement parallelism
-
product
PXI Dual 2x2 RF Matrix MCX 75 Ohm
40-837-102
The 40-837 is a 75 2x2 RF matrix available with 1 or 2 banks in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-837 modules.
-
product
GPS Antenna Signal Splitter 3 Way, N Type, Passive, L1 & L2, 50 Ohm
GPS300
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
-
product
PXI 2A Multiplexer, 1-Bank, 16-Channel, 8-Pole
40-614B-018
This 1-bank, 16-channel, 8-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Thermal Inducing System
Wewon Environmental Chambers Co, Ltd.
Design and development is the stage with the most type of thermal inducing system, It mainly includes oscilloscope, signal source, spectrum analyzer (signal analyzer), vector network analyzer and other general thermal management solutions, As well as channel simulator, terminal simulator, base station simulator and other dedicated thermal inducing system.https://www.wewontech.com/thermal-inducing-system/
-
product
Vehicle Multiprotocol Interface Module
C Series
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU i...show more -
product
6GHz Single Channel Signal Generator 19" 1U Rack Module
LS6081R
The LS6081R, 6GHz Single Channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” rack-mounted box. The LS6081R features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6081R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
Performance Board
The role of the performance board is accurate transmission of tester signals all the way to the device leads. Custom performance boards from ADVANTEST deliver support for DUTs (devices under test), as they become faster and smaller, with greater pin counts, and increasingly take the form of SMDs. ADVANTEST performance boards also support a host of test requirements, such as analog test, high-speed performance, and high-density, for testing state-of-the-art ICs.
-
product
PXI Single Bus 74-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-301
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Data Acquisition & Control
With these DAQ systems, you can acquire and digitize signals from variety of sources and sensors, store the data, analyze it, and present the results in local and remote locations.
-
product
SparkFun Single Lead Heart Rate Monitor
AD8232
The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily.
-
product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
product
PXI 2A Multiplexer, 8-Bank, 16-Channel, 1-Pole
40-614B-003
This 8-bank, 16-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2500 Series
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention eve...show more -
product
PXI Vector Signal Transceiver
The PXI Vector Signal Transceiver (VST) combines the flexibility of a software defined radio architecture and RF instrument class performance. You can use the VST to test a variety of cellular and wireless standards, and you can easily expand the VST's three-slot, 3U PXI Express form factor to support multiple input, multiple output (MIMO) configurations. The VST software is built on LabVIEW FPGA, and features several starting points for your application including application IP, reference designs, examples, and LabVIEW sample projects.
-
product
Preamplifier
2721
Pre-amplification is required to protect the output signal of pH and ORP electrodes from a wide variety of electromagnetic interferences common in industrial environments. Signet 2721 is used if remote pre-amplification is required (e.g. tank temperature >80oC) or connecting another manufacturer's electrode to the Signet 5700 or 8750 instrument. The Signet 2721 should be used with special order sensors built with cables (Signet models 277X-HT or 277X-1-HT).
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 4-Bank 6GHz SMA
60-802-004
The 60-802-004 is a 4-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Communication Data Logger
LE-270A
LE-270A is a Communication Data Logger, which records CAN/LIN communication logs in the SD/SDHC card for long hours. Using with a PC, it performs as a CAN/LIN protocol analyzer, and monitors data on the PC at real time (Line Monitor). Using without a PC, it performs as the CAN/LIN data logger, and saves data in the SD/SDHC card. It has two High-speed CAN transceivers, two Low-speed CAN transceivers and two LIN (TJA1020) transceivers. It monitors two channels of CAN or LIN, or one CAN and one LIN transceivers. In addition, four channels of Analog/Digital signals can be recorded.
-
product
IPM Drive
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
product
PXI Dual 6 Chan Mux 18GHz 50ohm SMA
40-785-522
Pickering Interfaces PXI Microwave multiplexer modules are suitable for switching 50_ signals up to 40GHz. The 40-785 is available as a single or dual 6 channel multiplexer, with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-01
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
product
LXI High Density 320x4 2-Pole 2A Matrix With BIRST
60-556-025
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
product
2.5GS/s 16Bit 2GS Mem 2CH 8 Markers AWG
P2582D
The Proteus P2582D, is a 2.5GS/s, dual channel arbitrary waveform generator packaged in a 4U, half 19” dedicated chassis, offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P2582D offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
product
Network Tester
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
