Showing recent results 1 - 15 of 1324 products found.
-
UNIVANS Co., Ltd.
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
-
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
Keystone Compliance
The reliability test program includes a number of qualification tests based on the type of product, the environment within which it is anticipated to operate in and estimated product weaknesses. Establishing an effective but practical and affordable test program can be a challenge. Reducing the number of units tested or the scope of testing might not yield a sufficient sample of results. Testing multiple units or having an expansive test program can be very time consuming and expensive. A very good resource for establishing a reliability test program is MIL-HDBK-781: Handbook for Reliability Test Methods, Plans and Environments for Engineering, Development, Qualification and Production. This handbook provides test methods, test plans and test environmental profiles which can be used in reliability testing during the development, qualification, and production of systems and equipment.
-
NI
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Advisor RDC - ACOEM
Advisor RDC is a subscription-based vibration analysis solution for maintenance programs looking to monitor the health of their rotating machinery. With our help the vibration data is collected, you upload the data to your RDC interface, and our team of experts will do the analysis and notify you of machine condition and next steps within 48 hours.
-
RT-300 - ACOEM
RT-300 is a customizable ecosystem of connected insights, which empower plants and teams to proactively identify maintenance needs, make smarter decisions and keep machine performance and profitability at optimum levels.
-
Innovative Circuits Engineering, inc
Our Reliability Testing Services make it possible for us to work with many different customers who manufacture devices that need tests such as pressure pot, temp cycle and more.The focus of our reliability testing lab is to provide our customers with an array of services and tests that fulfill all of their reliability testing needs. Whether you need preconditioning, thermal shock, pressure pot, or many other reliability testing needs, we are happy to be of service.
-
Underwriters Laboratories Inc.
Our reliability and durability testing services provide an accurate assessment of how your product may perform under expected and unusual use. We can help you meet regulatory requirements, gain actionable knowledge about the anticipated life cycle of your products and identify design flaws that have adverse effects on a product’s reliability and durability.
-
Sentinel Silicon™ - Ridgetop Group, Inc.
All manufactured products, including integrated circuits, are subject to wear-out and eventual failure. For applications where reliability is of primary concern, it is essential that on-chip state-of-health be constantly monitored. Traditional reliability testing provides an average lifetime and cannot predict the behavior of individual ICs. Sentinel Silicon is a library of die-level monitors that serve as "canaries in the coal mine," providing advance warning of wear-out in order to prompt mitigating actions to avoid catastrophic component and system failure.
-
National Technical Systems
NTS performs product reliability hardware testing to ensure that the quality and durability of a given product is consistent with its specifications throughout the product’s intended lifecycle. This testing can be done at both the design and production levels.
-
Aspen Test Engineering, Inc.
Reliability Test fixtures are fixtures that hold a specific product or printed circuit board that is put into a vibration or thermal chamber so that the product can be stressed with the intent of inducing premature failures. This type of testing will identify quality issues such as cold solder joints, bad wire crimps and weak components through the expansion and contraction (thermally) and through random vibration as would be seen in the field. The fixture shown here is intended to hold a Printed Circuit board for this purpose but we can make fixtures for many levels of assembly to determine issues.
-
Integra Technologies
Integra Technologies is an industry leader in providing qualification, design verification and reliability testing services to semiconductor manufacturers and military/space/aerospace and automotive OEMs. Integra offers a full range of qualification services as well as the technical guidance to define a qualification plan that meets your requirements.
-
Industrial Vision Technology Pte Ltd.
It is a known fact that even the accurate testing requires a frequent and appropriate calibration of solar simulator light intensity. A secondary calibrated reference cell can enhance the good practise for daily process serving as guide if any abnormities resulting from deteriorating components.
-
W8614EP - Keysight Technologies
The W8614EP Model Builder Program (MBP)Reliability Module MOSRA - TMI includes the extraction package for MOS Reliability Analysis (MOSRA) and the TSMC Model Interface (TMI) aging model.
-
VTC SERIES - EMIC Corporation
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
