Showing results: 46 - 60 of 87 items found.
-
PT-20MG -
TTTech Computertechnik AG
The PT-20MG expands the PM-200 data logger from the Power Family by adding six 1000BASE-T1 automotive gigabit Ethernet interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 1000BASE-T1 packets are time-stamped, filtered and sent to the data logger via a 1000BASE-T interface.
-
PT-15B -
TTTech Computertechnik AG
The PT-15B expands the PM-200 data logger from the Power Family by adding twelve 100base-T1 interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 100base-T1 packets are time stamped, filtered and sent to the PM-200 data logger via a 1000base-T interface.
-
PT-LabCar -
ETAS GmbH
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
VA&PT -
Precise Testing Solution
If new web applications are installed into your organization’s network, you have shifted your business physically to another network, or if your site requires IT governance and regulatory compliance, you should opt for Penetration Testing.
-
PT-55 -
V-Tek, Inc.
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
PT-1500 -
Molex, Inc.
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
PT-14 -
Kharkovenergopribor Ltd.
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
PT-1 -
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
PT-30 -
Standard Electric Works Co., Ltd
● Lightweight, compact, and easy to use.● 4000 counts.● Full automatic measurement, voltage measurement, resistor measurement.● Data hold function.● Auto off function.● Continuity check.● Diode measurement.● Low battery indication.● Pen light provided.● Backlight LCD.● 3V DC power supply.
-
Series 22 DT -
KELLER AG für Druckmesstechnik
Series 22 DT was developed and homologated specially for use in so-called "bivalent" vehicles fitted with engines for combined natural gas/gasoline operation. The unconventional design with a small mass swept by the flow results in a fast response with temperature changes, the temperature being measured by an NTC or PT sensor located directly behind the stainless steel separating diaphragm.
-
Orbit Controls AG
Data loggers with one or more signal channels for DC and AC voltages and currents, thermocouples, Pt thermometers, process signals and serial data interfaces RS232 / RS485 are designed for industrial use. They can also be used as monitors or process controllers with additional data and signal outputs for control purposes. The devices are designed for panel construction and have communication software for Windows applications.
-
NuVant Systems, Inc.
The spectroelectrochemical cell enables acquisition of infrared and Raman spectra of working electrode discs (variable sizes, up to 10 mm OD) under flowing solution. Working electrodes available include: Pt, Au, Ag, Cu, glassy carbon, etc. The cell uses a Pt-wire counter electrode and a Ag/AgCl reference electrode. For use with the EZpump peristaltic pump. Adapts to the Harrick Praying MantisTM Diffuse Reflection Accessory.
-
Ajinkya Electronic Systems
Besides from physical parameters; application also demands logging of voltages and currents. The IM2000 series Voltage Logger / Current Logger / Power Logger offered by us can accept DC shunt inputs, signals from convertors 4-20mA range or CT current inputs for higher AC currents or AC signals from PT. These can calculate values from the recorded channels to generate additional channel values.
-
HTCT-300 -
Lisun Electronics Inc.
Full-featured, can not only satisfy various CT (eg: protection, measurement and TP category) but also PT type electromagnetic unit for its excitation characteristics (ie voltage current characteristics), ratio, polarity, secondary winding resistance, secondary load, ratio deviation, angle deviation and other test requirements.
-
Dx10-PT-KIT -
Teledyne LeCroy
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead