- Pickering Interfaces Inc.
product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 67 GHz, 50 Ω, SMA-1.85, Remote Mount, Terminated, Failsafe
40-785C-473-TE
The 40-785C-473-TE (PXI) and 42-785C-473-TE (PXIe) are triple failsafe SP4T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
Multiplexor
SFT3107C
Hangzhou Softel Optic Co., Ltd.
SFT3107 series multiplexer is an enhanced TS re-multiplexer for digital TV broadcasting head-end system. The multiplexer has all the functions of normal TS multiplexer, including programs multiplexing, PSI/SI editing, PID re-mapping, service filtering etc. Also the multiplexer can insert EPG (Electronic Program Guide), CA (Conditional Access) and data casting information into each output stream.
-
product
Multiplexer
LI-8250
Central to a LI-COR long-term system is the LI-8250 Multiplexer. The LI-8250 acts as a single point of access to interact with and control a LI-COR gas analyzer and up to 36 chambers or flasks.
-
product
Multiplexer
SFT3107G
Hangzhou Softel Optic Co., Ltd.
SFT3107G Tuner Input Multiplexer is the latest demodulation and multiplexing device for digital TV broadcasting head-end system with TS output through IP port. It can multiplex up to 16 channels Tuner and 2 ASI input to IP (MPTS). This multiplexer has the functions of supporting auto-generation of PSI/SI information, PID re-mapping, and service filtering.
-
product
Multiplexer
SFT3504
Hangzhou Softel Optic Co., Ltd.
SFT3504 IP Multiplexer is a SOFTEL’s latest multiplexing model for digital TV broadcasting head-end system with TS output through 4 bi-direction ASI and 3 bi-direction data ports. It can multiplex up to 4 ASI and 768 IP inputs to 4 MPTS, and the amount of ASI output is based on ASI input (ASI port can be used as input or output). SFT3504 IP multiplexer has the functions of auto-generation of PSI/SI information, PID re-mapping, service filtering and PCR adjusting. In conclusion, its high integration and cost effective design make this device widely used in the CATV Broadcasting system.
-
product
Multiplexers
Our multiplexer are useful addition for routine or screening experiments in automated measurement setups. Sequential measurements can be carried out on the connected test objects in predefined routines or in customized protocols.
-
product
Octal Four-wire Multiplexer
SIM925
Stanford Research Systems, Inc.
The SIM925 is an eight input channel, four-wire multiplexer for low-level signal applications. Kelvin-lead measurements are supported with optional buffering of the two sense leads
-
product
PXI Multiplexer, 18-Bank, 3-Channel, 1-Pole
40-617A-021
The 40-617 18-Bank, 3-Channel, 1-Pole Multiplexer Module is part of our range of reed-relay based switching solutions. The Module consists of 18 electrically isolated banks of multiplexers controlled by a PXI/PCI interface. Each bank is a 1 to 3 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously.
-
product
High Voltage Multiplexer Plug-In
1260-136
The Astronics 1260-136 series plug-ins are high-voltage relay multiplexers delivering options up to 1kV for the Adapt-a-Switch® platform. These quickly and easily plug into the front of the Adapt-a-Switch Carrier 1260-100.
-
product
PXI Multiplexer, Dual 32-Channel, 1-Pole
40-630A-022-D/32/1
The 40-630A-022-D/32/1 is a dual 32-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Precision Low-Loss Multiplexers
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias b...show more -
product
PXI 10A Power Multiplexer, 4-Bank, 8-Channel
40-661A-002
The 40-661A-002 is a single pole, 4-bank, 8-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats.
-
product
PXI Power Multiplexer, 18-Channel, 1-Pole
40-665A-001
Model 40-665A-001 is a 18-Channel 1-Pole Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions).
-
product
Buffered Analog Multiplexers
Analog Devices’ leading edge buffered multiplexers are designed in single, dual or triple independent channels with two inputs (2:1) or four inputs (4:1) and are offered in standard plastic packages, as well as in space saving LFCSP packages. These multiplexers are very high speed primarily useful for switching video and RF signals with either 50 ohms or 75 ohms systems.
-
product
Hand Multiplexers
HG
HG hand torque multipliers are the ideal tools for applications where air and electricity aren't easily accessible. The gearing design allows for a high torque output with minimal input. Commonly used in petrochemical, power generation, transportation, shipping and maintenance industries.
-
product
DC-18GHz Coaxial Multiplexer
MS2102A
Universal Switching Corporation
Enhancing ATE systems and satellite monitoring, the System MS2102A is a compact high-performance modular switch multiplexer specifically designed for routing any coaxial signal within the DC-18GHz bandpass. Configurations are available from 1x10 to 1x100 (or dual 1x50), and custom configurations are a simple to accomplish. The 100 ports are normally open (reflective) when not routed. For a self-terminating version of this unit, please see Model MS2103A.
-
product
PXI/PXIe Very High Density Multiplexer, 5-Channel, 32-Pole
42-675B-002-5/32
The 40-675B-002-5/32 (PXI) and the 42-675B-002-5/32 (PXIe) are 5-channel, 32-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
product
PXI 2A Multiplexer, 2-Bank, 8-Channel, 8-Pole
40-614B-013
This 2-bank, 8-channel, 8-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI High Density Multiplexer, 5-Bank, 16-Channel, 1-Pole
40-615A-015
The 40-615A-015 is a 5-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
Sciospec Multiplexers
Ranging from 32 to 256 and more channels these multiplexers are the perfect choice for impedance measurements in any sequential multichannel setup. With constraint free any-to-any port assignments you can configure any 2, 3 or 4 port combination you need. The innovative SC98 connection standard gives you full flexibility for connecting to your application.
-
product
PXI Monitored Multiplexer, Quad 25-Channel, 1-Pole
40-619-104
The 40-619-104 is a high density PXI 2 A multiplexer module in quad 25-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
product
PXI 2A Multiplexer, 16-Bank, 4-Channel 2-Pole
40-614A-002
This 16-bank, 4-channel, 2 pole version is part of the 40-614A High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.These 2A multiplexer modules are designed for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PXI 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
40-614B-006
This 4-bank, 32-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 3-Bank 18GHz SMA
60-802-203
The 60-802-203 is a 4-channel, 3-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
High-Power PXI Multiplexer Switch Modules
Our High-Power PXI Multiplexer Switch Modules are based on electro-mechanical and solid state relays capable of switching currents of up to 40 Amps. Each module supports one or more multiplexer channels between one input/output terminal and a selection of output/input terminals. To reduce through path resistance, most of these multiplexers do not include isolation relays.
-
product
LXI Microwave Multiplexer, SP6T, 16-Bank, 67GHz, 50Ω, SMA-1.85
60-800-816
Our 60-800-816 is a 16 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 12-Bank, 26.5GHz, 50Ω, SMA
60-803-312
Our 60-803-312 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 40GHz, 50Ω, SMA-2.9
40-784B-043-E
The 40-784B-043-E (PXI) and 42-784B-043-E (PXIe) are triple SP6T 40GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
LXI Microwave Multiplexer, SP6T, 9-Bank, 67GHz, 50Ω, SMA-1.85
60-800-809
Our 60-800-809 is a 9 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe Microwave Multiplexer, Single SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-451-T
The 40-785C-451-T (PXI) and 42-785C-451-T (PXIe) are single SP4T 50GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI Single SP6T Multiplexer 50GHz 50, SMA-2.4
40-785B-551
The 40-785B-551 is a single 6-channel 50GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
