- Pickering Interfaces Inc.
product
PCIe Remote Control Interface Card
53-921-001
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
product
8-CH Relay Output EtherCAT Module
EPS-2308
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpos...show more -
product
Motion Control Platform
Deploy better machine control and motion systems faster with the powerful and intuitive Automation1 control platform.
-
product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
- Suitable for Mitsubishi J2 super servo- On-board connector type: 100-pin SCSI-II female- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
product
Advanced 4-Axis Servo & Stepper Motion Controller with Modular Design
PCIe-8154
The PCIe-8154 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8154 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous cont...show more -
product
6th Generation Intel® Core™ i7/i5/i3 Processor-Based Automation Control System with EtherCAT & 4CH GigE Vision Support
Talos-2000 Series
ADLINK's Talos-2000 Series ready-to-use automation control system, powered by 6th Generation IntelR Core? i7/i5/i3 processors, provides EtherCAT control and four independent PoE (power over Ethernet) ports, with data transfer rates up to 4.0Gb/s. The Talos-2000 Series offers motion control of up to 64 axes, 10,000 I/O points, and 4CH PoE camera connectivity with minimal footprint. The ideal solution for machinery automation, Talos-2110 integrates complete APIs for multi-dimensional, highly synch...show more -
product
REM-11152, 16-Channel (Input), 24 V, 2-, 3-, 4-Wire Digital Module for Remote I/O
784743-01
The REM‑11152 is a digital input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11152 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image proc...show more -
product
Centralized Motion Controllers
Pulse train motion controllers generate high-frequency digital signals to control servo motors and steppers, matching performance and precision positioning of high-performance servo amplifiers.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8132.
-
product
Voltage Input Module For Remote I/O
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
product
Robot Software
Our fully integrated software enhances productivity by combining control, safety, motion and more into a single software architecture and development environment.
-
product
Temperature Input Module For Remote I/O
The Temperature Input Module for Remote I/O features a features a thermocouple input range of ±100 mV and a voltage input range of ±5 V. It also has an adjustable filter time for improved measurement quality and optional external CJC or PT100 RTD measurements.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Temperature Input Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller o...show more -
product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
16-Axis PCIe EtherCAT Master Motion Controller
PCIe-8332
ADLINK PCIe-8332 is a hardware-based EtherCAT motion controller able to support up to 16 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in se...show more -
product
Linear Amplifiers
LA Series
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
product
Analog Output Module For Remote I/O
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
product
Mark II Dual Setpoint Monitor
95006
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
product
4-Axis Pulse Motion Controller
APM-104C
The AMP-104C is a cost-effective 4-axis motion controller card with a PCI Express® interface that can generate a pulse train up to 4.9MHz to control a motor. With more general purpose IOs and 4-channel encoder feedback input, the AMP-104C can be used for a multitude of scenarios or applications. As a motion controller, the AMP-104C provides non-symmetric acceleration and deceleration speed profile settings, T-curve and S-curve speed profile control, and selection of motion stop method. Also,changing speed on the fly with a single axis operation, linear Interpolation with any 2 axes, and simultaneously start/stop on multiple axes are also available.
-
product
DSP-Based 4/8-Axis Advanced Motion Controllers
PCI-8254/8258
ADLINK's new PCI-8254 and PCI-8258 incorporate up-to-date floating-point DSP and FPGA technology to provide high-speed and high performance hybrid analog and pulse-train motion command. Leveraging ADLINK Softmotion technology, the PCI-8254/PCI-8258 offer more comprehensive and application-oriented motion functions to reduce the development time but maintain superior throughput and accuracy. Also delivered is excellent synchronous motion control performance.
-
product
Motion Control Components
- Control of versatile robotic structures, including "yaw", "pitch" and "roll" motion capabilities- S-curve velocity profiling, based on polynomial splines and Bernstein-Bezier curves- Continuous path control in multi-segment smooth trajectories- Synchronization of multiple axes- Trajectory control with user defined velocity profiles- Kinematical modeling of open and closed loop mechanisms- Singularity consistent path planning and singularity avoidance- Optimal PID filter tuning- Automatic adjus...show more -
product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784227-01
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
product
Rotary Displacement And Encoders
Industrial rotary encoders and length sensors that provide precision motion control feedback for processes requiring the need to measure and control speed, position and distance.
-
product
64-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8338
ADLINK PCIe-8338 is a hardware-based EtherCAT motion controller able to support up to 64 synchronized axes and over 10,000 points simultaneously. The PCIe-8338 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in se...show more -
product
Distributed Motion Control Solution
The AMONet RS-485 series of distributed motion control products are categorized as Slave Modules and Master Cards. The AMAX-1220/1240/2240 series are used to increase the number of axes for distributed motion control networks.
-
product
Test, Measurement, Automation Development & Integration
ViArch Integrated Solutions, Inc.
ViArch Integrated Solutions, Inc. (ViArch) is a premier test, measurement, and automation solutions provider. ViArch specializes in high speed analog & digital signals, motion control, instrumentation, software, and data management solutions. ViArch offers a full slate of services for our customers.
-
product
DSP-Based 4/8-Axis Advanced Motion Controllers
PCI-8254/8258
ADLINK's new PCI-8254 and PCI-8258 incorporate up-to-date floating-point DSP and FPGA technology to provide high-speed and high performance hybrid analog and pulse-train motion command. Leveraging ADLINK Softmotion technology, the PCI-8254/PCI-8258 offer more comprehensive and application-oriented motion functions to reduce the development time but maintain superior throughput and accuracy. Also delivered is excellent synchronous motion control performance.
-
product
EPIC Embedded Board
The EPIC board is a small industrial-grade embedded SBC with optional I/O expansion via PC/104, PC/104-Plus, USB, Ethernet, etc, supporting advanced processors plus complex I/O functions for various applications. The size of EPIC embedded SBC is midway between the industry standard PC/104 module and EBX board. The EPIC embedded SBC supports advanced processors plus complex I/O functions for applications involving data acquisition, video processing, telecommunications, networking, motion control, and more.
-
product
Testing System
OpTest™ MTF
The Optikos OpTest™ MTF Testing Equipment is the most flexible and complete system for characterizing the optical performance of optical elements, lens assemblies and optical imaging systems in Infinite Conjugate, Finite Conjugate and Afocal configurations spanning the UV, Visible, NIR, SWIR, MWIR and LWIR spectral regions . OpTest™ software drives Optikos hardware, is easy to use and controls all motion control, image acquisition, configuration set-up and data reporting.
-
product
4-Channel Motion Control And High-Speed Trigger And Module For The Bridge Connected To EtherCAT
ECAT-4XMO
The ECAT-4XMO is EtherCAT SubDevice module with high-speed position comparison trigger and encoder re-drive function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications. Additionally, the ECAT-4XMO has 4-axis motion control with bridge function between EtherCAT and non-EtherCAT. Advanced motion control functions help machine and equipment builders to increase their motor selection portfolio, like linear, step, servo, direct drive, and AC motors, making it ideal for a variety of automation industry applications.
-
product
Standalone ARM-based Motion Controller
Advantech provides standalone 6-axis pulse train motion control AMAX-3110 and ARM-based EtherCAT I/O Controller AMAX-324 IO for rapid development.
