Showing results: 1141 - 1155 of 9890 items found.
-
NI
The C Series Voltage Output Module helps you update analog output models that feature overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. This module includes up to 16 channels. Some models include a channel-to-earth ground double isolation barrier for safety and noise immunity as well as improved signal quality, and some higher density models conserve chassis space, which leaves room for other measurement types.The C Series Voltage Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
NI
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
410112561 -
Virginia Panel Corporation
The 6” deep 75 Module enclosure has four handles to help place the ITA on the Receiver. The cover of the enclosure is secured by 14 ¼ turn fasteners to allow wiring access.
-
SCS-812 -
Alligator Technologies
The SCS-812 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 100kHz(elliptic mode) and 0.5Hz to 50kHz(linear phase mode).
-
410120120 -
Virginia Panel Corporation
This ITA, Adapter Plate and Enclosure package provides an opportunity for customization and is an alternative to the ITA with removable cover. Protective cover is also included.
-
ES620 -
ETAS GmbH
This module measures temperatures using 16 electrically insulated measuring channels for temperature sensors. The adjustable acquisition rate per module is 10 samples/s to 0.1 samples/s. Signal smoothing occurs through a parameterized software filter, and high measuring accuracy is possible through 21 Bit resolution. The automotive measuring range is -210 C to 1372 C (-346 F to 2502 F); J, K, and N type thermocouples are used. Data transfer to PC occurs via Ethernet.
-
NI
PXI Digital Reconfigurable I/O Modules feature a user-programmable FPGA for onboard processing and flexible I/O operation. You can completely control the synchronization and timing of all signals and operations along with custom onboard decision making. The PXI Digital Reconfigurable I/O Module is suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom communications protocols, bit error rate testing, and other applications requiring precise timing and control.
-
Macom Technology Solutions Holdings Inc.
MACOM’s High-Power Switch and Bias modules are extensively used in 4G and 5G TDD base stations as well as aerospace and defense applications. The PIN Diode Switch features high power handling, low insertion loss, and super board band performance. The integrated bias controller utilizes a boost circuit and provide the driver circuitry to the switch. The modules require only a single 5 V supply, and a single TX / RX control signal which greatly reduced the customer design complexity.
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer high power transmit and receive Front End Modules (FEM) for 5G mmW Advanced Antenna System. The fully internally matched FEM includes a multi-stage power amplifier, low noise amplifier, T/R Switch, and directional coupler. Featuring low noise figure, high output power and high linearity, and small size, MACOM FEM can be used as a front-end module for each antenna, for large antenna arrays, or in front of multi-channel Beamformer ICs.
-
mOByDic7100 -
Ozen Elektronik Inc.
This device allows a J1939 and ISO 15765 communication on the CAN BUS. Fully automotive compliant. This module allows different CAN BUS formats using the dual CAN BUS controller.
-
DTM-3224 -
DekTec Digital Video B.V.
The DTM-3224 is a highly-integrated and cost-effective OEM module for converting four ASI transport streams to IP. The next-generation architecture of this device has support for IPv6 and for IGMP v3, enabling source-specific multicast.
-
Peritec Corp.
It is a PXI module to output as a camera link signal NTSC video signal.For outputting a trigger signal when you have the image conversion, you can ignore the delay at the time of conversion.
-
W8614EP -
Keysight Technologies
The W8614EP Model Builder Program (MBP)Reliability Module MOSRA - TMI includes the extraction package for MOS Reliability Analysis (MOSRA) and the TSMC Model Interface (TMI) aging model.
-
V250 -
Highland Technology, Inc.
The V250 is a single-wide, 6U VME module that provides 64 non-isolated channels of digital input/output. Each 16-channel bank shares programmable pull-ups and input thresholds with a range of 0 to +10 volts.
-
NI
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.