-
product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix topology With Column Protection Resistors
782385-10
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
LXI Scalable Matrix - 8Amp 8x10 Matrix Plugin Module
65-239-202
The scalable matrix chassis offers you a solution that can be easily re-configured by the insertion and removal of sub-cards. It is purchased as an empty chassis with a quantity of sub-cards required for a particular matrix size. As your requirements evolve, additional cards can be easily fitted. When new cards are added, the control software automatically detects the new configuration.
-
product
Next Generation Network Testing
UX400
The VeEX UX400 is the smallest multi-service transport test solution to offer test capabilities ranging from DS1/E1 all the way up to 6x 100G traffic generation, supporting the latest 100G/40G optical pluggable form factors (CFP4, CFP2, CFP, QSFP28, QSFP+, no adapters required). Its modular architecture allows for up to six independent test modules and up to twelve concurrent tests or combinations of tests, including legacy PDH/DSn, SDH/SONET, OTN, Ethernet, Fibre Channel, CPRI/OBSAI, C/DWDM spe...show more -
product
cDAQ-9174, 4‑Slot, USB CompactDAQ Chassis
781157-01
4‑Slot, USB CompactDAQ Chassis - The cDAQ‑9174 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9174 also has four 32‑bit general-purpose counters/timers. With multiple timing engines, you can run seven hardware-timed operations simultaneously, with three independent rates for analog input.
-
product
PXI Triple Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-533
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PXI 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-614B-015
This 1-bank, 128-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Test Solution
Eye-BERT MicroX
The Eye-BERT MicroX is a compact, easy to use test solution offering high performance bit error rate testing at a fraction of the cost of competing solutions. The unit is offered in two speed grades including the X10 which operates up to 14.5Gbps, and the X30 which extends the data rate to 29Gbps. Its broad data rate capabilities and long test patterns make this unit suitable for testing nearly all optical SFP, SFP+, and SFP28 transceivers in production with just one unit. The real-t...show more -
product
CPCI-S.0 Standard Compliant Peripheral Board Controlled by a PCIe Channel Derived from the Backplane Connector P1
MIC-3820
MIC-3820 is a 2.5" on board SSD/HDD carrier board running at SATA Gen3 speed. A fast swap of the drive can be accomplished via a reserved thumb screw to help open a door on the front panel and eject the drive. The excellent mechanical design makes it easy to replace modules.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 1.5k
40-265-404
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Compact, Industrial Thermal Camera
Dione 320 CAM Series
The Dione 320 CAM series is based on an uncooled state-of-the-art 12 μm pitch detector with 320×240 pixels and NETD of less than 40 mK (available upon request) or 50 mK.The camera cores are optimized for low SWaP (Size, Weight, and Power). The Dione 320 CAM is both light weight and small. It utilizes Xenics image enhancement for advanced image processing while keeping power consumption low.All Dione 320 versions have the same SAMTEC ST5 connector and are GenICam compliant. Dione 320 CAM is a LWI...show more -
product
PXI 12-Slot BRIC Matrix, 33x16 1-Pole (3 sub-cards)
40-562B-321-33X16
The 40-562B-321-33X16 is a high density BRIC12 matrix module with a size of 33x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
NVIDIA® Jetson Xavier™ SOM-Based Platform for Rapid Development of ROS and AI Applications
ROScube Pico NPN
The ROScube Pico Series is an integrated development board powered by an NVIDIA® Jetson Xavier™ NX and Nano system-on- module (SOM) platform designed for rapid development and deployment of ROS and AI applications. The straightforward design allows users to quickly get started on development using open-source ROS libraries and packages. In addition to NVIDIA JetPack SDK, the ROScube Pico NX/Nano supports the full complement of resources provided by ADLINK’s Neuron SDK, Neuron IDE, and Neuron Library. The ROScube Pico NX/Nano is especially suited for robotic applications that demand cost-effective deployment without compromising AI computing capability.
-
product
Xilinx Artix-7 FPGA SoM
TE0710
Sundance Multiprocessor Technology Ltd.
TE0710s are industrial-grade FPGA modules integrating a Xilinx Artix-7 T FPGA, a gigabit Ethernet transceiver (physical layer), 1 Gbit (128 Mbyte) DDR3 SDRAM with 8-bit width, 32 Mbyte Flash memory for configuration and operation, and powerful switch-mode power supplies for all onboard voltages.
-
product
Smart Card Module Test Cells
Current and voltage measures are executed on defined pins, in stable conditions.Measurements:- Open/short- Input leakage current- IDD Supply instant/average current test (static/dynamic mode)- Input capacitance @13 MHz and inductance- Retro modulation index (RMI)Test of passive devices:- Capacitors- Resistors- Resonators
-
product
Calibrator Module
CAP CAL
The purpose of CAP-CAL is to check the correctness of Tan Delta and Capacitance of TD 5000 and TDX 5000. The calibrator includes an extremely high accuracy high voltage capacitor, which comes with a certificate issued by ISA - Altanova Group lab.
-
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector
42-153-104
The 40/42-153-104 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 37-pin D-type male connector.
-
product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 3.55kΩ
40-252-023
The 40-252-023 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI Express Hybrid Peripheral Module
SMT712
Sundance Multiprocessor Technology Ltd.
The SMT712 is a PXI Express (opt. Hybrid) Peripheral Module (3U), which integrates two fast 12-bit DACs, 2 banks of 1GByte DDR2 memory each, a clock circuitry and a Virtex5 Xilinx FPGA, under the 3U format.
-
product
Miniature Axial Extensometers
Model 3442
Jinan Testing Equipment IE Corporation
Weighing as little as 8 grams, these miniature extensometers are designed to have very low operating force with minimal specimen influence. All use an improved version of Epsilon’s dual flexure design which makes them very rugged for their size. With a module height of 15.2 mm (0.6 inches), they will fit in the limited space between grips that is typical with small test samples. Gauge lengths can be as short as 3 mm or as long as 50 mm. A newly designed gage setting pin and assembly allows the g...show more -
product
PXI Automotive Ethernet Interface Module
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
product
ITA, G12x, Front Mount, 18 Module
410104474
The G12x ITA can be used with all G12x Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
product
Intel® Wireless-AC 9260 Wi-Fi + Bluetooth M.2 2230 Module Card with Cables and Antenna Kit
EWK-M2-AC9260
- Bluetooth 5.1- IEEE 802.11ac wave 2 (Wi-Fi 5)- Operating Temperature : 0°C to 70°C (-40°C to 75°C extended)- Compact M.2 2230, A/E key form factor with cable and antenna kit to support flexible installation
-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, an...show more -
product
PCIe-8398, x16 Gen3, PCI Express Host, 13.6 GB/s Device for PXI Remote Control
784179-01
The PCIe-8398 is a host interface card used to control a PXI Express chassis over a software-transparent PCI Express Gen 3 x16 link. The PCIe-8398 is installed into a x16 PCI Express slot of a desktop or rackmount PC and is connected to a PXIe-8398 or PXIe-8399 PXI remote control module using Gen 3 x8 copper cables.
-
product
I/O Module
VPX3-611
Curtiss-Wright Defense Solutions
The VPX3-611 I/O module allows customers to readily incorporate a wide variety of I/O into military and aerospace embedded computing systems. Using a simple and reliable Flash-based FPGA hardware architecture with flexible I/O signal routing, the VPX3-611 provides high data throughput performance and can be easily adapted to meet a wide range of application needs.
-
product
PXI/PXIe High Density Matrix Module, 128x2, 1-Pole, 2A, 60W
42-584A-001
Our model 40-584A, along with the following models 40-585A, 40-586B and 40-587A are high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays. This module is also available in PXIe format (42-584A-001).
-
product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5290 Series
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
