-
product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 8-Channel, 2-Pole
40-614D-004
The 40-614D-004 (PXI) and 42-614D-004 (PXIe) 8-bank, 8-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Structural Durability Products
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
-
product
Backplane Twinax Connectors
We have taken the standard housing configuration of the P1 & P3 mounting dimensions while incorporating true differential pair contacts within the P1 & P3 dimensional constraints. P1 connector housing contains 21 position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P1 type housing.
-
product
SWIR InGaAs Camera Module For Short Exposures
XSW Gated Series
The XSW 320 Gated series is based on in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The XSW 320 Gated modules are able to provide maximum frame rates up to 400 Hz. The exposure time of the sensor is configurable from 100 ns up to 1 ms in steps of 100 ns, or from 1 ms to 40 ms.
-
product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
product
3U cPCI PPC SBC
75SBC4
NAI’s 75SBC4 is a 3U cPCI NXP™ QorIQ® P2041, PowerPC-based, Single Board Computer (SBC) with dual, high-speed/high-performance function module slots for configurable multifunction I/O interface expansion. Ideally suited for rugged defense, industrial, and commercial applications, this low-power, cost-conscious, SBC delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
product
OEM Modules
*Transports up to 6 GHz*19 grams, 40 x 18 x 8 mm*Operates from 5 VDC*Supports +20 LNA integration*Remote monitoring via I2C interface*Optional transport down to 1 MHz*CWDM*SMF and MMF support*Up to 36 modules in a 1RU chassis
-
product
Sensor
VL53L1
The VL53L1 is a state-of-art Time-of-Flight (ToF) laser-ranging miniature sensor. Housed in a miniature and reflowable package, it integrates a SPAD (Single Photon Avalanche Diodes) array, physical infrared filters and optics to achieve the best ranging performance in various ambient lighting conditions, with range of cover glass options.Unlike conventional IR sensors, VL53L1 uses ST’s latest generation direct ToF technology which allows absolute distance measurement whatever the target color an...show more -
product
Multi Protocol 8000 Modules
The M8K module can be one of many protocols that is used on a variety of platforms for the 8000 Multi Protocol Board.
-
product
200-Pin LFH Connector Block, Male
40-965-200-M
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780968-01
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
product
Battery Cell Formation System
17000 series
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy direct...show more -
product
PXI BRIC8 FIBO Matrix Dual 186x4 2pin brkout
40-592A-116
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module
782615-02
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-01
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
product
Quad M Module Carrier
DP-cPCI-5112
DP-cPCI-5112 provides a compact high performance cPCI bus gateway to four ANSI approved M-Module Interfaces. This is a non-intelligent 6U form factor M-Module Carrier board. The DP-cPCI-5112 allows a flexible I/O solutions to be implemented in the carrier board. The M-Module carrier board occupies single slot in a CompactPCI system. Different mix and match of various I/O solutions will simplify the job for system integrators.
-
product
3.5" Single Board Computer
RSB-4760
RSB-4760 is a RISC 3.5" single board computer (SBC) powered by Qualcomm ARM® Cortex®-A53 APQ8016 processor that supports full HD display and intergrades on board wireless solution – Wi-Fi, BT and GNSS. RSB-4760 also features in mini PCIe, M.2, and SIM card slots for expanding connectivity capability, like 3G, 4G/LTE modules. Equipped with complete Android, Linux and Debian BSPs, this SBC enables customers to easily develop unique application on specific OS.
-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, an...show more -
product
5.0 MP Camera For Rockchip RK3399
E-CAM50_CU96
e-CAM50_CU96 is a 5MP Fixed focus MIPI camera for 96Boards compliant Rock960 developer kit featuring Rockchip RK3399 processor. This 4-lane MIPI Camera for Rock960 board is based on our popular low-light camera module, e-CAM55_CUMI0521_MOD which has 1/2.5" AR0521 CMOS Image sensor from ON Semiconductor® and a built-in Image Signal Processor (ISP). It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
product
cRIO-9058, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
787880-01
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9058 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing a...show more -
product
Laser Modules
Our high-quality laser modules, designed for precision and reliability. Our laser modules can emit a bright, focused dot or a crisp, straight line, making them perfect for a wide range of applications.
-
product
PXI Single 24:1 High Voltage Power MUX
40-331-001
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-041
The 40-297A-041 (PXI) and the 42-297A-041 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 201 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
RF Training Kit And Lab Sheets
Y1800A
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
product
PXI Voltage Amplifier SMB Type Connector
41-650-002
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PCB GPTC03, 10 mV/g, IEPE, Accelerometer, General-Purpose Vibration Sensor
780988-01
The PCB GPTC03 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the … Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB GPTC03 features a sensitivity range of 10 mV/g and requires a low-noise coaxial cable.
-
product
PXI 8-Slot BRIC Matrix, 44x8 1-Pole (2 sub-cards)
40-562B-121-44X8
The 40-562B-121-44X8 is a high density BRIC8 matrix module with a size of 44x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 4 Slot BRIC Matrix, 2A 1-Pole 64x12, 2 Sub-cards
40-597A-002
The 40-597A-002 is a PXI 1-pole 64x12 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 200 VDC/210 VAC. The 40-597A BRIC modules are available in 2, 4 or 8-slot sizes to suit most high performance PXI matrix requirements, constructed using high quality electro-mechanical relays for high switching confidence.
-
product
PXI Programmable Step Attenuator Module, DC to 26.5 GHz
M9168C
The M9168C is a programmable step attenuator module based on PXI hybrid platform. The M9168C operates from DC to 26.5 GHz with a guaranteed 0.03 dB insertion loss repeatability for each section throughout the 5 million cycles operating life. Superior attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
product
PXI MUX 2 Banks of 64 Channel 1 Pole
40-610-022-2/64/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
