Filter Results By:
Products
Applications
Manufacturers
MW
Electomagnetic waves with wavelengths longer than those of infrared light. Frequencies range from 1 GHz to 300 GHz.
See Also: Microwave, RF, Millimeter Wave
-
product
Laser-Pumped White Light Source
LS-WL1
Our LS-WL1 is a laser-pumped white light source with a light output of up to 440 mW from a 600-µm fiber and a wavelength range of 450 – 700 nm, designed especially for professional requirements for extremely high luminance.
-
product
Wideband Transmitter
SMDWB
To meet the demands for a variety of RF environments and applications, the “WB” series SM transmitters offer selectable output power of 25, 50 and 100 mW (25 and 50 mW for export versions). With higher power output, the operating range is improved, or, a more secure link can be relied upon for high RF noise environments. Battery life is unchanged with the different RF power selections.
-
product
Plug-On Transmitter
DPR
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. The DPR can tune in 100 kHz or 25 kHz steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 25 or 50 mW. The purely digital architecture utilizes AES 256-CTR encryption for high level security applications.
-
product
SP1T RF Pin Diode Switches To 18 GHz
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
product
Laser Fault Locator
FOD 111
The Laser Fault Locator FOD 111 is a Laser Source with an output power of 1 mW in SM or MM fiber. It works from two AAA batteries. The universal adapter allows to use the Laser Fault Locator FOD 111 with all popular connectors without changing the adapter. If you need to test a patchcord, to find fiber breaks, or identify one fiber from ten - this instrument is for you!
-
product
Reduced Voltage Motor Starting Panels by Reactors
A method to limit motor starting current is a series reactor. Iron core or air core reactors can be used for starting purposes. If an air core is used for the series reactor then a very efficient and reliable soft starter can be designed which is more suitable for high MW ratings of synchronous/induction motors at MV levels. The reactors are designed with taps.
-
product
Multi-channel S-band Klystron 2.45 GHz / 5 MW
Insight Product Co. 's multi-channel S-band, 2.45 GHz, klystron provides up to 5.0 MW of output pulse power.
-
product
Bidirectional DC Source / Sink With Regenerative Power Supply
LAB / HPR
LAB / HPR DC sources are controllable 19 "bidirectional voltage sources in the power range from 7kW to 1.4 MW. The devices work bidirectional - load and power supply in one, thus energy recovery with high efficiency. As developers and manufacturers, we can also implement your individual wishes in addition to our standard device.
-
product
Thin Film Lithium Tantalate (TFLT™) Pyroelectric Detectors
For room temperature measurement of THz sources, from nW to mW.
-
product
Desktop MW Signal Generators
The Desktop platform offers all the functionality of a fully featured full-size MW analog signal generator in the smallest footprint module available on the market. Its small size enables using it as a desktop unit or easily scaling up to hundreds of channels, while keeping the required space to a minimum, let it be 20 GHz or 40GHz, excellent signal quality and integrity and fast switching speeds.
-
product
Amplifiers
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
product
Monitors
MW Series
The MW Series contains cutting edge, two-way, stage monitor systems designed for any high-energy live performance stage.
-
product
S-band Klystron 2.45 GHz / 5 MW
Insight Product Co. 's S-band, 2.45 GHz, klystron provides up to 5.0 MW of output pulse power.
-
product
Aeroderivative & Heavy-Duty Gas Turbines
GE’s heavy-duty and aeroderivative gas turbines are efficient, versatile and reliable with individual output ranging from 34 MW to 544 MW. They are proven performers in simple and combined-cycle operation for pure power generation, cogeneration, mechanical drive, and waste-to-power.
-
product
Compact Fiber Seeders
LightWire FPS Series
LightWire FPS series fiber lasers are dedicated for seeding solid state Nd:YAG amplifiers. Compact, cost efficient FPS series models deliver sub‑10 ps pulses at 1064 nm wavelength with the average output power up to 200 mW and pulse energy up to 50 nJ.
-
product
Particle Size Analyzers
NanoBrook Series
Brookhaven Instruments Corporation
Rapid and accurate protein & nanoparticle size distributionsMultimodal & unimodal size distribution softwareISO 13321 and ISO 22412 compliant resultsRange: < 0.3 nm to 10 mThree measurement angles: 15, 90, and 173Ideal for fast, routine sizing applications in research or quality controlHigh power 35 mW diode laserDynamic light scattering at 173 and 90Temperature control, -5 C to 110 CCompact bench top unit, USB connectionMolecular weight determination (relative and absolute through Debye plot)
-
product
ECPR System (Electrically Calibrated Pyroelectric Radiometer)
Rs-5900
Developed in conjunction with NIST, the Rs-5900 ECPR is a ±1% absolute accuracy radiometric transfer standard for the visible to near-IR (0.25-2.0µm), with the RsIR Option extending the ±1% accuracy to >20µm. The RsP-590 Pyroelectric Probe requires no cooling and maintains ±1% accuracy from 1 µW to 100 mW. The ECPR uses an auto-nulling, electrical substitution technique that allows the instrument to be referenced against NIST electrical standards, insuring maximum accuracy and precision. Unlike most electrically calibrated radiometers, there is a direct correlation between electrical and optical heating because the same material serves as both the optical absorber and electrical heating element.
-
product
Belt-Pack Transmitter
SMQV
To meet the demand for both extended operating range and extended battery life, the "V" series SM transmitters offer selectable output power (See specific model data sheets for details). A third selection at 50 mW is provided for some theatrical applications where the system design specifies lower transmitter power.
-
product
Generators From 30 To 110 GHz
MHP Series
Insight Product Company offers powerful mm-wave sources with CW power up to 400 mW and central frequency up to 110 GHz.
-
product
RF / MW switch
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
product
Laser
BDS-SMY Series
*Pulse Width Down to 50 ps*Repetition Rate 50 MHz (20 MHz Available on Request)*Free Beam or Fiber Output*CW-Equivalent Power 0.3 mW to 0.5 mW*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
product
Average Reading Directional RF Wattmeter
81000-A
The Model 81000-A Wattmeter ... now you can measure RF Power in 50-Ohm coaxial cable and transmission lines, and accept plug-in elements in the range of 100 mW to 10 kW full scale, and from 0.45 to 2300 MHz.
-
product
SP16T RF Pin Diode Switches To 10 GHz
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
product
MW Signal Generators
The Lucid analog signal generator Desktop platform offers all the functionality of a fully featured full-size RF/MW signal generator in the smallest size module. You can use it as a desktop unit or easily scale up to hundreds of channels. Being a modular platform the Desktop signal generator is a solution for enabling customizing according to customers’ requirements and applications’ needs.
-
product
Pulse Magnetrons Up To 220 GHz And Peak Power Up To 10 MW
Insight Product Co. offers 7 pulse magnetrons models for industrial and scientific applications.
-
product
Low-Barrier Schottky Diode Detector, 10 MHz to 18 GHz
8470B
The Keysight 8470B 18 GHz Low-Barrier Schottky Diode (LBSD) detector has been widely used for many years in a variety of applications including leveling and power sensing. It offers good performance and ruggedness. Matched pairs (Option 001) offer very good detector tracking. A video load (Option 002) extends the square-law region to at least 0.1 mW (-10 dBm).
-
product
Miniature Fluxgate Magnetometer
WFG-120
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
product
Multi-Channel S-band Klystron 2.856 GHz / 6 MW
Insight Product Co. 's multi-channel S-band, 2.856 GHz, klystron provides up to 6.0 MW of output pulse power. and has two regimes of operation.
-
product
AccuDyne™ AC Dynamometer Systems
SAKOR Technologies offers the AccuDyne™ series of AC motoring dynamometers. These 4-quadrant dynos offer full motoring as well as loading capabilities. AccuDyne dynamometers can be used for testing active components such as engines and electric motors as well as passive components such as transmissions, generators and alternators. AccuDyne dynamometers are available in models from 5 kW through 3 MW. SAKOR Technologies configures each AccuDyne system to meet customer-specific requirements.
-
product
Extreme Low Power Detector Laser Power Meters
11XLP12
11XLP12 extreme low power detector is best suitable for low power im both the µW and mW regimes with very low thermal drift. Featuring broadband flat spectral response, minimal thermal drift and a noise equivalent power as low as 1 µW the 11XLP12 is ideally suited for measuring any pulsed or CW low power laser.
