Showing results: 766 - 780 of 2290 items found.
-
MFJ-267 -
MFJ Enterprises, Inc.
1.5 kW Dry Dummy Load has built-in precision, true peak-reading SWR/Wattmeter switchable to external antenna! Worlds most versatile 1.5 kW dummy load has a built-in true peak reading SWR/Wattmeter that you can switch and use independently! Youll find tons of uses! Tune up your transceiver, linear amplifier, or antenna tuner into a safe 50 Ohm dummy load at full power.
-
Radio Ampstik® 2023 -
SensorLink
The Radio Ampstik uses the same current sensor technology as the original SensorLink Ampstik. It quickly takes accurate current measurements and direction of current flow indication. Knowing source and load direction is essential for power system protection, load balancing, and metering.
-
Anchor Test System -
James Instruments Inc.
Two models, each with two different gauge capabilities enable precision readings over a wide range of applications - from light to heavy duty loads. The standard system has a pull stroke of two inches with an option to extend to four inches. The longer pull stroke allows for complete extraction of most fixings in one simple operation. A load diffusion bridge and pyramid are available to keep reaction loads away from the anchor point.
-
Series LS10 -
Teledyne Relays
Series LS10 DC solid-state relays are designed for mounting on printed circuit boards. They facilitate heat-sinking by providing an interface surface. They can switch loads with high starting currents. The nominal switched currents depend on the size of the heat sink These relays use a direct-bonded copper substrate for thermal efficiency and long life.Available options include:LS60DC10C-21 10A, 7-36 Vdc Load; 3-10 Vdc ControlLS60DC10F-21 10A, 7-36 Vdc Load; 7-30 Vdc Control
-
-
-
-
-
-
-
PI-41401 -
Pulse Instruments
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-
TCAT-2DF -
Physitemp Instruments
This is a combination version which includes both and AC outlet for controlling primarily resistance loads such as heat lamps, AC powered warming blankets and a low-voltage, low noise DC output for heating pads. This version allows you to controls a variety of different loads.
-
EE301-I2C -
Executive Engineering
Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable
-
B-1009 -
ROSS ENGINEERING CORPORATION
The Step-Start Vacuum Circuit Breaker/ Power Controller is designed for extra heavy duty repeated fault, crobar and load interruption for sensitive equipment. It is designed to limit initial closing inrush current to approximately load or other maximum current with an adjustable step delay.
-
Series HD -
Teledyne Relays
The HD solid-state relay utilizes the latest technology to provide a low ON resistance and an optically isolated output. The control circuit is buffered to enable the relay to be driven directly from standard CMOS or open-collector TTL logic circuits. Available options include short-circuit and current overload protection. The second option is a status output line.MSL 1HD relays are controlled with 3.8-32Vdc Available options include:HD00CF 2.1Adc, 60Vdc LoadHD02CF 2.1Adc, 60Vdc Load; with switch statusHD20CF 2.1Adc, 60Vdc Load; with short circuit protectionHD22CF 2.1Adc, 60Vdc Load; short circuit protection & switch statusHD24CF 2.1Adc, 60Vdc Load; short circuit protection & trip status
