-
product
Coaxial Cable Drivers & Amplifiers
B-1020
*Wideband: DC to over 30MHz*Maximum Output: to 10V PK, 20V PK-PK*Maximum Input: ±5V to ±200V PK-PK as required. Also to 900kV PK with Ross Voltage Divider*Signal Isolation: 500,000 Ohm 450V PK*Input Impedance: Up to 2 Megohms*Load Impedance: 50 Ohm or greater*Power Source: AC or Optional Battery*Will drive over 500 Feet of Coaxial Cable
-
product
Archival Storage Rooms
Darwin Chambers Company’s NFPA, GSA, and NARA Directive 1571-compliant Archival Storage Chambers are engineered to provide maximum value, efficiency and conformance with all applicable standards and codes. Archival chambers provide environmental controls for storing records and materials (including paper documents and items with high fibrous content, various films, microfiche, and photographic materials) that require permanent protection for storage and preservation. Our high-performance systems...show more -
product
Serial to Parallel Controller
E84 SPC
300mm equipment manufacturers utilize this off-the-shelf E84 communications controller to provide SEMI E84 compliant communications for their products. With its built-in Load and Unload algorithms it is the perfect E84 communications solution for process tools, stockers, load ports, FOUP buffers, smart storage shelves and simulation load ports. The E84 SPC easily integrates with equipment controllers through a standard serial communications connection.
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting i...show more -
product
Signal Generator, Audio, Handheld, 1 Channel, 150kHz, AM, US Plug
72-505
*Hand held audio generator*20Hz to 150KHz in 46 steps*±0.5dB sine wave output 1.2V RMS (no load) and square wave output SV p-p max (no load)*Dimensions: 150mm × 83mm × 25mm*Low battery indicator
-
product
Automatic Capacitor Batteries
Lifasa - International Capacitors, SA
The batteries of capacitors for automatic AT are designed for those applications in which the power levels in the AT network are variable. This type of equipment, with a number of steps normally between 2 and 4 to avoid phenomena in the installation resulting from the connection and disconnection of the capacitors in the electrical network, is controlled by a type MCX regulator, which tunes and regulates the input of the steps according to load levels, taking into account the expected waiting times of AT that between consecutive connections is 600 s., this time we can reduce it to less than 10 s. if we install TP for fast download.
-
product
Dual-Phase Relays
Series SD
Series SD dual-phase relays are designed for all types of loads. The design incorporates two relays in a single package. The relays utilize optical isolation to protect the control from load transients. High-current models are excellent for motor and phase angle control. SD relays are available with faston or screw terminals, and Zero-Cross or Random switching.-06 = Faston TerminalsAvailable options include:SD24R50 50Arms, 12-280Vrms, 600Vpeak Load; 4-30Vdc Control; RandomSD24D40-0...show more -
product
Computery Control Torsion Tester
SG-L10
The machine is mainly used for torsion test of metal and nonmetal,also it is applicable to the torsion test of parts and members. Servo-motor and cycloid gear reducer are introduced to the loading system in this product, the system for measuring torque and distortion angle are composed of high accurate torsion sensor, photoelectric encoder and computer measuring force.It possesses automatically tracking test torque and distortion angle, maintaining maximum peak load and displaying loading speed....show more -
product
Test Automation System for Driveline Testing
STARS Driveline
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
product
Acceleration Testing
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
product
Mechanical Testing
A range of processes including:Tensile and Compression Load TestingA test piece or component is subjected to tension (or compression) until either a proof load is achieved or failure occurs.Testing can be carried out on both metallic and some non-metallic materials.
-
product
Damping Pads
With damping pads from the SLAB series, ACE provides solutions to effectively slow down loads impacting large and small surfaces. This means that these products are found in a wide range of damping technologies from ACE where oscillation begins or where damaging impacts in construction designs need to be slowed over a large surface.
-
product
Loop Calibrator
Model KM CAL-904-MK1
Kusam Electrical Industries Limited
• 4-20mA (1kΩ Load, 24V Loop Output).• 0-20mA and 0-24mA output ranges.• 0.025% Basic Accuracy.• Auto Ramp and Step functions.• 0-100% output with percentage step option.• 0-24V DC voltage source.• Open loop and overload buzzer alarm.• Low battery indication.• Simple Operation Interface• Warning beeper when output is open• Pollution Degree 2.• Ambient temperature 0~40℃.• Power Consumption 150mA at 24V 1kΩ load
-
product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
product
4-Amp Solid-State Single Inline (SIP) Four-Pin Relays
Series BS
Series BS 4-amp solid-state single inline (SIP) four-pin relays are designed for mounting on a printed circuit board. BS relays can withstand very high current overloads. The compact size and triac output make the BS relay an excellent choice for switching medium power resistive loads. All Series BS relays are Zero-Cross switching.Available options include:BS24D4A 4Arms, 15-280Vrms, 600Vpeak Load; 3-10Vdc Control
-
product
DC Power Supplies
SGX Series
AMETEK Programmable Power, Inc.
The Sorensen SGX Series represents the next generation of high power programmable DC power supplies. The SGX Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a full 15 kW available down to 20 V output in a 3U package the SGX leads the industry in power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.
-
product
Digital Input/Output Expander (Normally-Open Relay Contact Outputs)
ENVIROMUX-DI16DOR16
Adds 16 digital inputs and 16 digital normally-open relay contact outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for normally-open relay contact outputs. Accepts 26 to 16AWG w...show more -
product
Unclamped Inductive Load Tester
ITC55600C
Model ITC55350 is the high current (600A) version of theITC55100 tester. The ITC55350 performs the same testsas the ITC55100 and includes many features that improvetesting accuracy, test results collection, test resultsviewing, and multiple tester networking
-
product
Transconductance & Transimpedance Amplifiers
Measurements International Ltd.
0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.
-
product
Bench Power Supply, Calibrated w/D & U, Adjustable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2690 CAL DU
The 72-2690 CAL DU from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has complete digital control, intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
product
DMS Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
PXI/PXIe Power Relay Module, 3xSP4T, 20 Amp
42-166-201
The 40/42-166-201 is a PXI/PXIe high density power relay module with 3xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
product
Desktop Meter Qualification Board
2199
Providing complete capabilities for evaluating meters and communications performance, TESCO’s Desktop Meter Qualification Board (Catalog No. 2199) can generate any voltage and load conditions the meter may encounter in the field. Apply non-sinusoidal voltages with complex load waveforms. Perform disconnect tests and reconnect tests without having to worry about being able to drive the meter’s switches.
-
product
PXI 5A Power Multiplexer, 2-Bank, 24-Channel, Independent Isolation
40-651A-102
The 40-651A-102 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC.
-
product
Military-Style DC Solid-State Relay for High-Current Pulse Load Applications
Part No. M33-2N
The M33-2N is a military-style DC solid-state relay designed for high-current pulse load applications. It features the latest power FET output technology to minimize ON resistance. This feature provides minimum output voltage drop and allows the M33-2N to switch high pulse currents up to 100 amps at higher temperatures than those allowable with bipolar devices. The M33-2N utilizes transformer isolation to protect against transients, and are through-hole mountedMSL 1 Available options include:M33-2 7Adc, 60Vdc Load; 4.5-5.5Vdc (bias voltage), 80µA (CMOS) Control;
-
product
Loadcell Simulators
Micro Edge Electronics Private Limited
With the assistance of our team of professionals, we are offering Load Cell Simulators to our esteemed clients. its price range Rs. 5000 to 12000 .These are ideal to be used for troubleshooting, pre-calibration trials and linearity checks. The offered simulators are fabricated using the finest grade raw material and latest technology in compliance with the set industry standards
-
product
High Speed Shock Dynameter, 40" Masts
102092-40
3HP High Speed: 0.5 to 55 in/sec. Adjustable Stroke: 1.0", 1.5", 2.0" or 2.25". Type K Thermocouple Sensor. Runs on 220V Power. Scotch Yoke System. 2,000lb Load Cell
-
product
Signal Conditioner
ClipX
Fast and digital signal conditioning for force sensors, load cells, torque sensors, pressure transducers, as well as temperature and standardized signals (current/voltage). Guaranteed measurement accuracy, even in harsh industrial environments with electrical interferences.
-
product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Hopper Weigher
This weigher can be easily installed in a hopper for faster construction by adopting our prominent load cells with built-in constrainer.
