Showing results: 1 - 15 of 52 items found.
-
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
Dr. Hubert GmbH
Isolation amplifiers are indispensable components for signal conditioning. There are several reasons that make galvanic potential isolation necessary. Examples for this are personal protection, on the one hand, as required in medical engineering to ensure contact of persons with life-threatening voltages. On the other hand, different safety aspects, such as protection of IT systems may require the use of an isolation amplifiers. If ground loops need to be separated or if a small differential voltage with a high common-mode level must be determined, the isolation amplifier is the device of your choice.
-
Analog Devices Inc.
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
-
X005 Series -
Positek Limited
The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.
-
Knick Elektronische Messgeräte GmbH & Co. KG.
To feed and Isolation of 2-wire transmitters / sensors or SMART transmitters with HART transmission. Working voltage up to 2500 V AC / DC. Available for hazardous and non-hazardous area.
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Measurement of DC or AC voltages up to () 3600 V and of large DC currents to about () 20 kA with shunt resistor or directly in the device to () 5A DC and AC. Variants with calibrated range selection.
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
Renesas Electronics Corp.
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Renesas Electronics Corp.
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
ProDAQ 5828 -
Bustec Ltd.
The ProDAQ 5828 Isolation Amplifier Signal Conditioning Card is designed to isolate and amplify wide bandwidth analog signals. It provides 16 channels with complete galvanic isolation and can be used directly with any of Bustec’s high-performance ProDAQ 3416 16-channel Sigma-Delta ADC Function Cards.
-
41-650-001-S1 -
Pickering Interfaces Ltd.
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
41-650-001 -
Pickering Interfaces Ltd.
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
41-650-011 -
Pickering Interfaces Ltd.
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
41-650-002 -
Pickering Interfaces Ltd.
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.