Showing results: 3436 - 3450 of 5968 items found.
-
763061-16 -
NI
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
763061-003 -
NI
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
763061-06 -
NI
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
ROM-8720 -
Advantech Co. Ltd.
Advantech ROM-8720 COM Express Type 7 Compact Computer-on-Module is powered by NXP LS1046A SoC which includes four Arm Cortex-A72 cores for Edge networking and Edge firewall, two 10Gbsp-KR and up to four Gbps for the networking communications. Three PCIe, three USB 3.2 Gen1 and three USB2.0 for the embedded interface expansions. two UART, one SPI and 8 GPIO for embedded device controls.
-
DDS8m -
Novatech Instruments , Inc.
The DDS8m generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The DDS8m is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. SOF8 windows software is available as an extra cost accessory.
-
Advantech Co. Ltd.
MicroATX (uATX) or mATX Industrial Motherboard is only 244 x 244 mm and suited for space/cost sensitive applications where less than 4 slots are required. mATX enables the same high integration of ATX but with a smaller footprint that fills the gap between MiniITX and full size ATX, balancing performance and expansibility. Equipped with LVDS interface, longevity and revision control, MicroATX(uATX) is ideally suited for medical and instrumentation applications.
-
Acroname, Inc
As part of Acroname's MTM series, the MTM-IO-Serial module is a key component to manufacturing test systems for electronic devices using a standard USB 2.0 interface, serial UARTs and one or more interface voltages. The MTM-IO-Serial module features a software controlled USB hub (USB 2.0 high-speed) with four controllable channels. Each channel has switched data and 500mA current-limited power lines.
-
DUCA-LCD -
Ducati energia S. p. A.
Energy Analyser for DIN-rail mounting (4 modules), for Single-Phase/Three-Phase systems with Graphic LCD screen, Co-generation Energy measurement and "Wide Range" Power Supply (24 - 240 Vac/dc); voltage and current waveforms and harmonics measurement and visualization; 2 digital output for pulses or alarms; 2 digital pulse input. Optional RS485 serial line interface (Modbus or ASCII_DUCBUS), Ethernet Interface (Webserver / Modbus-TCP).
-
ST8675 -
Shenzhen Sintech Electronic, Inc.
1. This NEW generation (Version 5in1) of Notebook POST CODE Testing Card supports five bus interfaces: MINI PCI, Mini PCI-E ,LPC.ELPC and I2C (Notebook Battery Interface) .2. This card is easy to use for end users and it works with high stability. It is your ideal and useful tool for notebook repairing partner.It can diagnosis signal which show the problem of CPU, Memory, display card and so on.
-
MEXA-ONE -
HORIBA, Ltd.
MEXA-ONE offers an intuitive user interface with a highly efficient hardware and software design.This results in increased testing efficiency and economical facility operation, while enhancing reliability and accuracy. These advancements are possible because the MEXA-ONE software employs new "HORIBA ONE PLATFORM". This platform integrates the test devices in an emission cell into a single user interface, increasing efficiency and optimizing user control over the entire testing process.
-
50-200-008 -
Pickering Interfaces Ltd.
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
50-200-004 -
Pickering Interfaces Ltd.
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
GT4000 -
Guide Technology, Inc.
A true breakthrough in high-speed, asynchronous and serial interface test technology the GuideTech GT4000 leverages the power of CTIA continuous time-stamping technology to eliminate the need for supplemental triggers, pattern markers or clock recovery circuits. GuideTech CTIAs enable serial interface pattern verification and full jitter analysis in milliseconds for fast, automated characterization or high-throughput production test on any ATE platform, including low-cost and in-house testers.
-
BCO, Inc.
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
01-09838 -
DragoonITCN
Non-ruggedized module that addresses concerns regarding use of untrusted, commercial-off-the-shelf (COTS) bus logging on aircraft with a MIL-STD-1553 or ARINC-429 bus interface.