Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Male, 2m
40-971B-200D-2m-MM
This male rear exit to D-type 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
Material Identification Spectroscopy
ChipCHECK
Gastops specializes in advanced fluid sensing and analysis systems specifically designed and developed for critical equipment condition monitoring applications.ChipCHECK offers the fastest way of making on-site equipment maintenance decisions. It is a field deployable analyzer designed for rapid on-site identification of equipment lube oil. This automated maintenance decision-support tool employs innovative laser spectroscopic technology, which enables on-site analysis of microscopic chip debris. ChipCHECK provides the maintainers with quick, reliable, and conclusive information, including the total number of particles, and the size, shape, and specific alloy classification for each individual particle on the sample.
-
product
Proactive Downstream Spectrum Analysis
SpectraVizion
SpectraVizion is an innovative, software-based diagnostics tool that leverages new advancements in remote spectrum capture, allowing cable operators to address downstream spectrum impairments proactively, before subscribers call in with service complaints. “Troubleshooting downstream spectrum issues has always been a reactive process for cable operators,” said Arthur Skinner, Vice President of Worldwide Sales for ZCorum. “Often they’re not aware they have an issue until a customer calls, and that’s when they then send a technician to the home with a hand-held meter to start a search for the problem.” SpectraVizion takes the guesswork out of problem identification and location by presenting on a simple dashboard a list of devices that are experiencing common downstream issues like Standing Waves, FM Noise, Suck-outs, Roll-off and Tilt. The tool leverages the spectrum data available from cable modems and set-top boxes that support full band capture, and advanced detection algorithms automatically identify devices experiencing downstream impairments. The operator can click on any device in the list to view a capture of the full spectrum from that day, or up to 30 days in the past.
-
product
Identification & Marking
Try best-in-class automatic identification, machine vision and verification technologies.
-
product
Counterfeit Analysis / Screening Services
DPACI perform counterfeit part analysis on all types of electrical, electronic, and electromechanical (EEE) components. Our suspect counterfeit analysis task groups include source identification, manufacturer validation, external visual inspection, mechanical inspection, electrical test, X-Ray, in-depth internal visual and materials analysis. With one of the largest databases of test reports for EEE components, we can offer similar historical data for correlation with images, test data, certifications and reports.
-
product
Constantan, Type T (°C) Contact
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
Amine Blush Swab Test Kit
139
The Elcometer 139 Amine Blush Swab Test Kit is a rapid colorimetric test designed solely for the use in the quick and immediate qualitative identification of amine blush (carbamates) on the surface of coatings using surface swabs. The presence of amine blush is indicated by a visual change of colour of the test solution when compared with a control sample.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Female, 1m
40-971B-200D-1m-MF
This male rear exit to D-type 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
Analytical Instrument
LabSpec 4 Hi-Res
Analytical Spectral Devices, Inc.
The LabSpec 4 Hi-Res analytical spectrometer is designed for analysis of materials that are characterized by sharp spectral features that may require more resolute spectral data for accurate detection and identification.
-
product
HYBRID LED CIRCUIT TESTER, 12-42V
MD1651
*Tests standard automotive electrical DC 12-42V circuits*Safe for low current circuits and hybrid vehicles*Automatic voltage identification featuring blue for under 40V and red for over 40V
-
product
Fiber Identifier
Fiber identifier is an essential installation and maintenance instrument which can identify the optical fiber by detecting the optical signals transmitted through them,during this process the fiber optic identifier generate no harm or damage to the fiber cable and it do not need opening the fiber at the splice point for identification or interrupting the service.This fiber identifier detects frequency tones at 270Hz, 1KHZ, 2KHZ, when traffic is present on the fiber under test, an audible tone can be heard. In the meantime, it can identify the traffic direction that indicated by LED with illumination.
-
product
LC/MS/MS Method Package For Water Quality Analysis
Shimadzu provides method files, including pre-registered MRM parameters with optimized quantitative and reference ions, LC separation parameters, and retention times and peak identification parameters for each compound, as well as report templates for outputting quantitation results, as a package. If retention times are adjusted when the system is introduced, based on the HPLC configuration delivered, the analysis process can be started as soon as the specified columns, mobile phases, and standard samples are supplied.
-
product
Optical Identification
Application areas of the 1D/2D code reader range from product tracking and product control to product identification.The sensor can read 1D and 2D codes regardless of their position. Even if up to 25% of the code information becomes damaged or soiled, it is still read correctly. The reader can also be used for optical character recognition (OCR), e.g. in order to identify products based on type labels or serial numbers.
-
product
Near Field Probes 30 MHz up to 6 GHz
XF1 set
The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
product
Cable Sheath Fault Location
Locating cable sheath faults is one of the last steps in cable testing, occurring after you have identified the existence of a cable fault via the identification procedure based on your specific site variables and the type of system you are working on
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Male, 1m
40-971B-200D-1m-MM
This male rear exit to D-type 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
RFID Software
Radio Frequency Identification technology, commonly referred to as RFID, uses electromagnetic fields for the purposes of identifying and tracking objects. More recently, the technology has moved into mainstream applications that speed up the handling of manufactured goods and materials by attaching RFID tags to them. RFID technology has been around since the 1970s but its high cost and limited practical applications have discouraged its use up until recently.
-
product
Thermocouple, Contact, Receiver, Alumel, Type K (°C)
610113132
Primary mating contact 610113134.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Benchtop X-ray diffraction (XRD) instrument
MiniFlex
New sixth generation MiniFlex X-ray diffractometer (XRD) is a multipurpose analytical instrument that can determine: phase identification and quantification, percent (%) crystallinity, crystallite size and strain, lattice parameter refinement, Rietveld refinement, and molecular structure. It is widely used in research, especially in material science and chemistry, as well as in industry for research and quality control. It is the newest addition to MiniFlex series of benchtop X-ray diffraction analyzers from Rigaku, which began with the introduction of the original MiniFlex system decades ago.
-
product
Thermocouple, Contact, Receiver, Chromel, Type K (°C)
610113131
Primary mating contact 610113133.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Advanced IR Gas Analyzer For Process Monitoring
T-Series
T-Series Inline Gas Analyzer improves gas measurement accuracy over the traditional non-dispersive infrared (NDIR) analyzers using Tunable Filter Spectroscopy (TFS™), a spectroscopic scanning technique capable of generating slices of spectra in the infrared region. Each scan produces an absorption spectrum which is used to identify compounds and provide concentration values. TFS technology improves gas identification accuracy and selectivity by subtracting out spectra from interferent gases within the same infrared regions. This spectral processing capability also provides multi-component measurement.
-
product
2.5mm Visual Fault Locator
3105
Anfkom International Co.,Limited
The 3105 Pen type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:Finding the breakpoint, poor connections, bending or cracking in fiber optic cables.Finding the faults of OTDR dead zoneEnd-to-end visual fiber identification
-
product
SM / Expansion Unit
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
product
High-Resolution Spectroscopic Personal Radiation Detector
identiFINDER® R300
The identiFINDER R300 is the world’s highest performing, pager-sized spectroscopic personal radiation detector (SPRD). It provides continuous detection and full threat identification (ANSI N42.48 library). The simple two-button user interface facilitates expedited threat response. Visible, audible, and tactile alarms rapidly alert the operator via the easy-to-read color display. On-board Bluetooth, web server, and GPS technologies make interagency communication easier than ever. The R300 is ideal for belt-worn passive-scanning, security checkpoints, border patrol, and first response.
-
product
Spectrum Analyzer & Sat TV Instrument
Satlook Color HD
Spectrum-analyzer 950-2150MHz. • DVB/S S/2 -receiver 920-2150MHz. • Super bright 5" 16:9 TFT-LCD color display. • Automatic Satellite identification. • Readout of NIT - gives SAT ID and TV/Radio-channel info. • Digital BER and S/N-ratio (DVB-S, S/2). • QPSK and 8PSK constellation diagram. • DVB-S (Free to Air) and SAT-analog TV-picture. • LNB voltage 13/18V, 22KHz tone switch. • DiSEqC according to level 1.0, 1.1 and 1.2. • SatCr-control (UniCable). • Favourite channel list (100 channels) for FTA DVB-S. • Lots of memory positions for spectrum pictures. • RS232 for PC-connection (up/download). • Rechargeable Li-Ion battery.
-
product
PXI-5670 , 2.7 GHz RF Vector Signal Generators
778768-04
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
product
Saybolt Chromometer
K693
Chongqing Kailian Yongrun Industrial Co.,Ltd.
To determine the Saybolt Color of refined petroleum products, such as undyed motor and aviation gasolines, jet propulsion fuels, naphthas, kerosene and petroleum waxes. It is used for quality control and product identification purposes on refined products having an ASTM Color of 0.5 or less.
-
product
The Modern Personal Radiation Detector
D3S PRD
The D3S PRD personal radiation detector is a high-speed PRD or SPRD replacement that is a cost-effective radiation detection and preliminary identification device for first-line users. It fits on your belt or even in your pocket giving you radiation alerts for gamma and neutron radiation plus the ability to identify what isotopes have been found. It is the only PRD that detects the presence of radiation and also displays the isotope identified and it does all this in seconds.
-
product
Optical Fiber Identifier
BD-IF400D
Shanghai Baudcom Communication Device Co.,Ltd.
BD-IF400DOptical Fiber Identifier is an important tool for optical maintenance, which isused for nondestructive fiber identification project. Meanwhile it also hasVisual Fault Locator module with fault location function. Useingthe macro bending technology on line for nondestructive testing, BD-IF400DOptical Fiber Identifier can measure the signal direction and power and avoidmisoperation resulting in interrupted lines.