- Virginia Panel Corporation
product
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules
610132106
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules.
-
product
Pitot Static Tester / AoA TESTER
ADSE 744
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to creat...show more -
product
Safety Chamber, Hydrostatic Test
9901HTX-72x24x12
The 6 ft wide by 2 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
product
Energized Cable Sensor
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without te...show more -
product
Basic Fuel Pressure Tester Kit
FIT450
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose.
-
product
Fuel Cells
continuously variable contact pressure ensures complete reproducibility of the test conditions ● independent of the thickness of the fuel cell components due to the self-adjusting piston and special sealing concept ● no connection and disconnection of hose- or cable connections for the exchange of cellFixture necessary ● fast &Easy clamping of the cellFixture without tools and precise exchange of the internal cell components ● maximum power density by determining the optimal contact pressure on the active cell surface ● developed for high stress in the field of quality assurance and laboratory environment
-
product
Pressure Fittings
AMETEK Sensors, Test & Calibration
Our CPF Fittings & Hose are a new line of quick-test pressure fittings for calibration & test applications - designed with an emphasis on safety. Crystal Pressure Fittings (CPF) perform up to 10 000 psi / 1000 bar, and feature a safety weep hole to alert you before you accidently disconnect from a pressurized system. It can also be used as a bleed point. CPF fittings seals two ways: use fingers for an o-ring seal or use a wrench for a metal to metal cone seal (good to -40°C).
-
product
BASIC FUEL PRESSURE TEST SET
FPT1000
*Quickly and easily diagnose fuel-related issues on gasoline vehicles equipped with standard or small Schrader test ports as well as other popular applications*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary*Gauge features a dual-scale dial with ranges from 0-100psi and 0-7 bar with rugged boot and hook for hands-free reading and durability
-
product
Safety Test Chamber Kit for both new and existing 8801 and 9801 testers US Army, USAF
8801HT/9801HT
The 8801HT retrofit safety test chamber kit is designed specifically for existing 8801-8801B and 9801B hydrostatic hose test systems in the field. It may also be ordered complete with a new 8801B or 9801B tester.
-
product
Needle Pressure Gauge
102
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
product
Automatic Transmission Oil Pressure Tester
ATG5AK
Checks oil pressure in automatic transmissions and gasoline engines on most domestic and import cars and light trucks. Includes 6' of oil proof nitrile hose to make testing easier as well as standard and metric fittings. 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar. 3-1/2" gauge has a dual scale dial with ranges from 0-400psi and 0-28 kg/cm2.
-
product
Pneumatic, Contact, Receiver, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610131101
Primary mating contact 610132101.Pneumatic Contacts are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
product
Line Switching Unit Series
TestVonics™ Line Switching Unit (LSU) is a multi-port distribution unit which can provide up to 6 outputs from one channel of controlled pressure. The LSU distributes pitot static supplies for the external services and connection of hose assemblies for testing of aircraft Pitot and Static ports. The lightweight unit is housed in a highly durable and easy to maneuver case.
-
product
Pitot Static Breakout Box (PSBB)
C-17
The C-17 Pitot Static Breakout Box is a derivative of TestVonics™ Line Switching Unit (LSU) Series. The assembly includes a multi-port distribution unit which provides 4 Pitot and 8 Static outputs from one channel of Pitot and Static controlled pressure. The LSU distributes pitot static supplies for the external services and connection of hose assemblies for testing of aircraft Pitot and Static ports for the C-17. The lightweight unit is housed in a highly durable and easy to maneuver case. Additionally, four (4) 30ft Pitot Hoses, eight (8) 30ft Static hoses, and two hose storage bags are included with the assembly.
-
product
Pressure Pumps, Fittings And Hoses
Practical Instrument Electronics, Inc.
Choose from 3 different pressure pumps depending on your requirements. All pumps are rugged metal construction with 2 outlet ports for connections, a fine adjust piston and a precision pressure vent. Pumps come standard with one 3′ 6900 PSI hose and a 1/4″ male NPT fitting.
-
product
thermostats
Cooling bath circulation thermostats - freezing test set of equipment 2 pieces for carrying out the freezing test with 42-2260 .... Complete with insulated connection hoses and connection elements as well as integrated circulating pumps for temperature control of a single or double sample. The temperature setting is software-controlled. For connection, 2 separate fused circuits per 16 A are required.
-
product
Vacuum Pressure Unit
TestVonics™ Vacuum Pressure unit provides clean, dry, filtered pressure and vacuum in a compact and rackmountable form factor. The lightweight unit produces low noise and the dry diaphragm pump provides oil-free use with a 4,500 hour maintenance interval. Two (2) 8 ft hoses are provided, one for Pressure and one for Vacuum.
-
product
Systems
Walter Stauffenberg GmbH & Co. KG
Custom-design and ready-to-install hydraulic pipe, tube and hose assemblies from port to port
-
product
Hybrid / Optical Dry Mate Connector
The Teledyne ODI Dry-Mate Submersible connector series is designed to directly complement the wet-mate hybrid connector series (Rolling Seal), and also for use as a stand-alone connection system. Two standard shell sizes are available, depending on the circuit configuration. In addition, straight, 45°, or 90° termination versions can be provided. Used in conjunction with Teledyne ODI's oil-filled hose, this system is designed for submersible applications up to 9,100 psi. A unique tri-lobe keying system assures proper alignment.
-
product
Hydraulic Hose Assemblies, 15,000 psi, US Army
9801B Tester
The 9801B hydraulic hose tester is utilized by the U.S. Army for high pressure testing of hydraulic hose and tube assemblies as well as any component testing requiring test pressures up to 15,000 psi. Enhanced safety for operating personnel is achieved by utilizing the optional 8801HT integral test chamber which was designed specifically to fit to all our 8801B and 9801B testers.
-
product
Extension Hose for Diesel Compression Testing
34729
Makes for easier diesel compression testing in areas with restricted clearance. Attaches between Cat. No. 34700, Diesel Compression Tester and Tool Aid brand diesel test adapters.
-
product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-36x36x15
The 3 ft. wide x 3 ft. deep Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
product
Pneumatic Contact, ITA, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610132101
Primary mating contact 610131101.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferruless fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
product
Save A Drop Water Meter
P0550
Is your water bill out of control? Part of the problem could be that you’re over-watering your garden! Now you can take control of both with the unique Save A Drop® Water Meter. Simply attach between the faucet and hose and the easy to read meter shows you how much water you’re using. It accurately measures both single waterings use as well as cumulative water usage to accurately meet your garden’s (and wallet’s) needs.
-
product
Radiator Flow Test Machine
8601
The Radiator Flow Test Machine P/N 8601 meets all requirements of military specification MIL-F-45955A (AL). It is completely self contained and requires only connection to a source of shop electrical power to place in operation. A power cable complete with three prong grounding plug is permanently attached to the machine for this purpose. The unit consists of a water storage tank, a pumping system, a flow measuring system, a support and workstation, and the required hose adapters for connection...show more -
product
Diesel Dynamometers
Heavy-duty toroidal water-brake or large eddy-current absorber, S-beam electronic torque transducer, high-flow manual (or optional electronic) engine load control, DYNOmite data-acquisition computer, rigid-frame engine test stand, wall (or stand) mounted control console, absorber to engine-block mounting adapter, heavy-duty input shaft, calibration arm, stainless-braided hoses, and full-function data wiring harness.
-
product
Abrasion Testers
Abrasion tester is used to determines the resistance of elastomers by the frictional loss of the rubber in products, such as tires, conveyor belts, hoses, footwear, floor covering etc.
-
product
Annular Port Source
8500
The principal feature of the revolutionary Annular Port Source design is the annulus within which the air chamber and shuttle valve are housed.The air chamber and shuttle valve, in turn, surround a hollow passage through which air supply hoses and electrical control cables are routed. Peak output is optimized by an increased surface area of the toroidal-shaped bubble compared to the spherically shaped bubble generated by a conventional 4-port air gun.
-
product
Pneumatic, Contact, Receiver, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610131104
Primary mating contact 610132104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
product
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules
610131108
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules.
-
product
Fuel Pressure Tester Kit
FIT500
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose and protective rubber boot.
