-
product
FieldFox Handheld Microwave Analyzer, 44 GHz
N9951A
44 GHz max frequency Carry world's most integrated handheld W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in a single sweep Simultaneously measure all four S-parameters Make accurate SA measurements ( 0.5 dB) without needing warm-up Easily measure average and pulse power with a USB sensor
-
product
3-Channel PXI Function Generator
41-620A-003
The 41-620A is a compact 3-channel function generator provided in a PXI 3U single-slot module and is fully backward compatible with our 41-620-003 module. It is capable of generating sine waves to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. This module can generate arbitrary waveforms loaded into the internal 256k memory, allowing the function generator to emulate many waveform types, including the typical waveforms of automotive and aerospace sensors.
-
product
Signal Analyzer
Choose from an extensive selection of signal analyzer products from DC to 44.5 GHz and extendable to 325 GHz.With excellent total level accuracy, dynamic range and performance, Anritsu spectrum/signal analyzers not only can capture wideband signals but FFT technology supports multifunction signal analyses in both the time and frequency domains. Moreover, the built-in signal generators on some models outputs both continuous wave (CW) and modulated signals for use as a reference signal source.
-
product
Frequency & Pulse Distribution
Timetech frequency distribution amplifiers and pulse distribution units.
-
product
Electrodynamic Vibration Generator System
LVD-100KG
• Vibration table size: 500*500mm (Other size can be designed) • Vibration: 0~5mm (Adjustable range P-P). Vibration waveform: sine wave (half wave and full wave). Acceleration speed: 0~20g (Adjustable) • Maximum test load Capacity: 100kg • Accuracy: Frequency can be displayed to 0.01 Hz. Precision 0.1 Hz. • Sweep Frequency function (1~600Hz): (Upper frequency, Lower frequency, Time range) It can set real standard arbitrarily to sweep frequency back and forth • Programmable Function (1~600Hz): It can set each segment in 15 segments arbitrarily (frequency/amplitude/time/acceleration), and it can be recycled • Frequency doubling function (1~600Hz): 15 segments multiplied-increase: 1)Low to high frequency 2)High to low frequency 3)Low to high and then to low frequency, it can be recycled • Logarithmic function (1~600Hz), 3 modes of logarithm/can be recycled: 1)Lower to upper frequency 2)Upper to lower frequency 3)Lower to upper and then to lower frequency • Measuring instrument: To display amplitude, acceleration speed and the maximum acceleration speed.
-
product
Heavy Duty Digital Multimeter
DMM 8007
1.999 count LCD display. Resistance to 2000 M£[. Frequency to 20MHz. Capacitance measurement. Inductance measurement. Logic Test. Transistor hFE test. Audible continuity test
-
product
Signal Combiner
Becker Nachrichtentechnik GmbH
In large scale RF signal distribution systems such as broadcast signal distributions, several signals of radio bands have to be transmitted over longer cable distances. Due to the different frequency ranges, the signals can be transmitted via one common coaxial cable. This saves costs for the coaxial cables and their installation. With help of signal combiners, multiple signal sources can be combined broadband or frequency selective to a sum signal with low loss in level.
-
product
CAT-5 Video Variable Filters
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
-
product
Leakage Current Clamp Tester with Bluetooth40mmφCT, ACA
M-1141X
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Waveform display is possible with connection to a smartphone・Measurement data is to be accumulated in the server, and it is available for graph and CSV output・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency (fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
product
Digital Clampmeters
AC Current 40A, 400A, 1000A AC Voltage 4V, 40V, 400V, 750V (Auto) (40-500Hz) DC Voltage 4V, 40V, 400V, 1000V (Auto) Resistance 400Ω, 4KΩ, 40KΩ, 400KΩ, 4MΩ, 40MΩ (Auto) Frequency 10.00 Hz, 50.00 Hz, 500.0 Hz, 5.000 KHz, 50.00KHz, 500.0 KHz(Auto) Sp. Functions Data Hold, Audible Continuity, Diode Test, APO Jaw Opening 43mm Max.
-
product
10:1 500 MHz 10 MOhms Passive Probe
PP005A
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MO. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
Active Dual Loop Antenna
KH30936
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
product
Pocket Size Digital Multimeter, Resistance Measure, 3999 Count, Average, Auto Range, 3.75 Digit
72-10395
Pocket sized multimeter which comes in a self-contained folding case. The meter measures AC/DC voltage, resistance, capacitance & frequency.
-
product
Sine-wave Vibro Viscometer
SV-10 Series
Newly developed Tuning-fork Vibration Method* promises you high accuracy and wide measurement range without replacing sensor plates!! *Patent pending. Sine-wave Vibro Viscometer SV-10/SV-100 measures viscosity by detecting the driving electric current necessary to resonate the two sensor plates at constant frequency of 30Hz and amplitude of less than 1mm.
-
product
Spectrum Analyzers
GAOTek spectrum analyzers can monitor the levels of spurious signals, such as intermodulation products, noise, harmonics and other signals, to see whether they meet the required levels by displaying the frequency of the signals on the horizontal scale and the amplitude of signals on the vertical scale. GAOTek sells these spectrum analyzers to the United States, Canada and Globally.
-
product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
product
Snap-on RF Current Monitoring Probe
TBCP2-250
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
product
VXI Rubidium/GPS Frequency Standard
3352A Series
The Racal Instruments™ 3352A Rubidium frequency standard module and the 3352A-GPS, its GPS-disciplined companion, set a new standard for high density functionality in a single width VXI module. Using ANSI Standard M-Module building blocks, the 3352A series integrates the functions of a Rubidium oscillator and clock distribution together with an optional trigger distribution module and an optional digital I/O (DIO) module.
-
product
PD Calibrator
PDCAL has excellent pulse-with stability; scale calibration factors are permanently stored inside its flash memory. Thanks to on board photo coupler PDCAL output pulse can be synchronized with the actual line frequency through external surrounding electrical light source systems.
-
product
Sound Level Meter, 30 dB, 130 dB, 1.5 dB, 0.1 dB, 0 °C, 40 °C
72-942
Compact Digital Sound Level Meter measures less than 9" in length, including the windscreen, yet provides selectable response time and frequency weighting. It is perfect for sound system testing, speaker system measurement and environmental noise level monitoring.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, External Termination, Failsafe, Remote Mount
42-781A-322-E
The 40-781A-322-E (PXI) and 42-781A-322-E (PXIe) are dual failsafe SPDT 26.5 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
RF spectrum analysers
Electronics laboratories instruments, technical schools and spectrum analysis in field for Wi-Fi, GSM, PLC and high frequency.
-
product
Common Rail Injector Test Bench
Nanyang NanTai Experimental Equipment Co.,ltd
It adopts advanced frequency conversion technology and digital technology with automatic and manualdouble control for the rotation speed, temperature and count.Equipped with displacement sensor, it can test different kinds of mechanical fuel
-
product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PCIe-6353 , PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device
81049-01
PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device - The PCIe‑6353 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality … leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6353 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Up-Converter for Radio Amateurs
. Internal filters provide high spurious rejection and image rejection. Due to low phase noise and high frequency stability of the local oscillator at 3000 MHz, the up converter is suitable for analog and digital communication systems.Typical applications are Multichannel Multipoint Distribution Systems (MMDS) using QPSK modulation and DVB?T or DVB?S systems. The output power of 20 mW can be increased to several watts by the use of an additional power amplifier.
-
product
Safety Voltage Detector
305 SVD
Standard Electric Works Co., Ltd
Bright LED visual indication. Audible indication. AC voltage detection: 100Vac ~ 69kVac. Frequency range: 40 ~70Hz. Easy-to-prove method. Self-test function. Power source: 9V alkaline battery. Non-contact detection by proximity. Convenient to use. Operating temperature and humidity: 0°C~40°C / 80% RH Max. Lightweight, robust and compact. Easy access to battery. Comply with EN 61326-1
-
product
Switch Filter Bank
Corech Microwave’s Switch Filter Bank frequency covers DC to 50GHz, featured with multi-channels (4 to 8 channels), high power handling, and fast switching options. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds.
-
product
Dual-Band RF Tuner and 4-Ch 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 58891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Four FPGA-based multiband DDCs (digital downconverters)- Two Xilinx® Kintex® UltraScale™ FPGA- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PXI Triple Microwave SPDT Relay 18GHz 50 SMA
40-780A-523
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
