Showing results: 2881 - 2895 of 4162 items found.
-
dbSAFE ARMOR -
DVTest Inc.
The dbSAFE ARMOR series of shielded boxes are cost-effective solutions for OTA testing in the mmWave spectrum. Providing a shielded, fully anechoic test environment, these RF test enclosures ensure stable and repeatable measurements over a wide frequency range (from 300 MHz to 90 GHz).
-
MGKS -
Holding Informtest
The MGKS vector signal generator is designed to reproduce arbitrary waveforms, as well as sinusoidal signals with amplitude, frequency, phase modulation or without modulation. The generator can be used for research, tuning and testing of systems and devices used in radio electronics, automation, computing and measuring technology, instrument making.
-
Instron
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Bourns
Bourns Miltilayer chip inductors offer high frequency, nickel barrier, monolithic construction for high reliability, and magnetically shielded construction providing low radiation. They are well-suited for DC-DC converters, and prevention of electromagnetic interference to signals on the secondary side of electronic equipment, among many applications.
-
Teledyne LeCroy
The PPE6KV-A and HVP120 can handle up to 6000 Vpeak transient overvoltages and are designed for probing up to 2000 Vrms and 1000 Vrms respectively. Fast rise times, excellent frequency response, and a variety of standard accessories make these probes safe and ideal for high voltage measurement applications
-
7999 -
Coaxial Dynamics
Now, you can extract a low signal level from a 50-Ohm coaxial system with the Model 7998 and 7999 series of Adjustable Signal Samplers from Coaxial Dynamics. These Signal Samplers are essential tools for spectrum analysis, RF signal scope observation, or frequency counting control.
-
CAA-100A -
ShinewayTech
DTF/Frequency Return Loss, VSWR, Cable Loss, RF Power and Spectrum. CAA-100A integrates two functions: cable and antenna measurements and spectrum analysis. Cable and antenna analyzer with frequency range 1MHz – 4.4GHz and 60dB dynamic range can suitable for 2G/3G/4G/WiMAX system etc.
-
7998 -
Coaxial Dynamics
Now, you can extract a low signal level from a 50-Ohm coaxial system with the Model 7998 and 7999 series of Adjustable Signal Samplers from Coaxial Dynamics. These Signal Samplers are essential tools for spectrum analysis, RF signal scope observation, or frequency counting control.
-
Megger Group Ltd.
Detecting cable earth faults in critical signal and supply systems is essential in critical applications such as railway installations, hospitals, power plants or other industrial facilities. By using a low frequency signal, inductive sensors and compensating signal, users can be guided to any cable short to ground.
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
There are CV, ACV, ACA, , CAP, Frequency, Diode Test, Continuity Test and Duty Cyclr Test function. Otherwise there are auto and manual range, relative measurement, data hold, and backlight auto off time limit mode. Test leads can be inserted on groove of back of the tester.
-
VT14 -
Chauvin Arnoux Metrix
12 V to 690 V voltage test (7 diodes)Indication of polarity by " + " and " – " diodesImpedance: 400 kΩOperating frequency: DC and 50/60 Hzovervoltage protection up to 1,000 VIEC 61010 600 V CAT IIIPowered by 1 x 9 V 6LR61 battery (supplied)
-
NSG-2 -
National RF, Inc
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
Greenlee Tools
*Measures AC+DC current*AC and AC+DC voltage measurements with digital low pass filter for accurate readings on variable frequency drives*Also measures DC voltage, resistance, capacitance and frequency*Tests continuity and diodes*Flashlight inside clamp jaw for easier work in dark locations*Backlight & relative mode for added versatility*Peak-RMS measures motor inrush current*AmpTip™ increases accuracy on small wires and low current*Two voltage detection modes - non-contact or using a single test lead*Data hold*Recording of Maximum, Minimum, and Average readings*Crest (peak hold) feature captures current or voltage peaks as short as 5 milliseconds
-
Extech EX430A -
Extech Instruments Corporation
The Extech EX430A True RMS Autoranging Multimeter (with K Type, Capacitance, Frequency, and Duty Cycle) is a professional grade True RMS multimeter capable of performing a wide range of measurements. Functions include AC and DC voltage to 600V, AC and DC current to 10A, resistance to 40MOhm, continuity and diode test. Also includes a Type K thermometer function for contact or air temperature measurements from -4 to 1832°F (-20 to 750°C). Advanced functions include Capacitance, Frequency and Duty Cycle. The meter comes complete with test leads, Type K temperature probe, 9V battery, protective holster, adjustable tilt stand and Velcro hanging strap.
-
LPSU -
AWT Global
Low PIM coaxial switch matrix 5 x 6 or 1 x 4 configurationFrequency range 698-2700 MHz.SCPI commands via Ethernet (wired or wireless).Significantly reduces test time for multi frequency PIM applications.Applications: ATE systems, multi-band antenna and component testing.