Showing results: 2776 - 2790 of 4162 items found.
-
Teledyne RF & Microwave
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
CAEN S.p.A.
CAEN has developed a complete family of digitizers that consists of several models differing in sampling frequency, resolution, form factor (VME, NIM, Desktop, Rack) and other features.In recent years CAEN opened the doors of its R&D to the Open FPGA technology, which is becoming more and more widely used and required. In addition, we decided to invest many resources in order to make this technology accessible to everyone. These efforts result in innovative Programmable Digitizer families and the SCI-Compiler software for easy-programming of the Open FPGA simplifying firmware writing with a block-based visual programming language.
-
HydroSweep DS -
Teledyne Marine RESON B.V.
The HydroSweep DS is a deep water multiebeam echosounder ideally suited for seabed mapping in deep water up to full ocean depth based on a sonar frequency between 14 kHz to 16 kHz. Beside bathymetric depth information from 10 m to more than 11,000 m, sidescan data and backscatter data for seabed classification are acquired. The HydroSweep DS does not only gather sea floor information, but also uses adaptive bottom tracking windows to identify sonar targets in the water column and can be optionally operated as a parametric sub-bottom profiler without additional transducers and electronics.
-
VibroLine -
IDS Innomic GmbH
The VibroLine devices are stationary analysis modules for continuous condition monitoring on machines and systems. The VibroLine condition monitoring system can be used to monitor vibration acceleration, speed or displacement with freely adjustable frequency filtering for different applications. Permanent vibration monitoring of your machines not only brings competitive advantages through the increased efficiency of your systems, but also protects against unwanted machine failures. With the VibroLine devices, you can monitor not only the sum, order and storage characteristics, but also impact characteristics. This offers you enormous flexibility in terms of monitoring parameters for your condition monitoring.
-
Series 1100 -
Eastern-Optx
The Eastern OptX Series 1100 Radar Target Simulator is a true propagation path replicator. The Series 1100 receives the signal transmitted from a radar system and adds the round-trip propagation delay associated with the target distance. That signal is then output to the radar receiver. The radar I/O may be connected directly to the Series 1100 or detected and transmitted using user specified antenna. For a moving target the system will add the appropriate Doppler shift associated with the target speed and radar frequency. The Series 1100 is broad band with ranges up to 40 GHz and with a dynamic range of over 100 dB.
-
S240 -
ThinkRF
The ThinkRF S240 Real-Time Spectrum Analysis Software features a completely redesigned graphical user interface (GUI) from previous versions. Designed with the end-user in mind, the S240 keeps common setting such as Frequency, Bandwidth and Amplitude visible at all times, making it easy for the user to get the right view. All other settings and functions are available through an intuitive menu system that minimizes the number of clicks and the time it takes to find the right functions, while still keeping the view of the spectrum front and center. Customized settings can be saved and reloaded to simplify the setup of common applications and uses.
-
Ducommun Inc
Ducommun's products include very broad ferrite device selections to cover 100 MHz to 110 GHz operation frequency range. These devices include narrow band drop-in (FID and FCD), connectorized (FIC and FCC), junction (FIW and FCW) isolators and circulators and iso-adapters (FII and FCI). The broad bandwidth versions are offered as full band junction isolators and circulators (FIF and FCF) and Faraday isolators (FFF). These devices feature low insertion loss, high isolation and wide operating temperature range. Low cost and volume production versions of these ferrite devices are available per customers’ request.
-
Teledyne Defense Electronics
Teledyne RF & Microwave has been producing Bulk Acoustic Wave (BAW) delay devices since the early 1960’s. Over the years,Teledyne has constantly improved BAW technology and is currently the world’s only supplier of microwave bulk acoustic wave delay devices. Markets for BAW devices include instrumentation and radar altimeters and are available in connectorized, pin and surface mount configurations.BAW devices operate as low as 300 MHz and as high as 17 GHz, usually in sub-bands of around 10%. Depending on the delay and frequency of operation the insertion loss is in the range 30 dB to 90 dB.
-
N1914A -
Keysight Technologies
Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature
-
346B -
Keysight Technologies
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
N1913A -
Keysight Technologies
Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature
-
R347B -
Keysight Technologies
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
BL HP Series -
Behlman Electronics Inc.
The BLHP Series Behlman's high power, AC Power Sources / Frequency Converters / Inverters, combine the smooth, clean power of a linear supply with the compact design of a switching power supply. They're about one-third the size and half the cost of other AC Sources. All models come standard with variable voltage and frequency, external sync and 0-10 Vdc remote control, optional IEEE488 or RS232 interface for computer controlled. LabWindows and LabView drives available. Small size, quiet operation and high efficiency make the high power BL Series ideal choices for precision avionics, ATE and industrial products testing requirements.
-
AFV-P -
Intepro Systems
Intepro’s AFV-P Series is a programmable AC/DC output power source with precision measurement and control. This compact power source comes in four power levels, 600VA, 1250VA, 2500VA and 5000VA, providing clean power with distortion less than 0.3% at 40-100Hz. The AFV-P series delivers output voltage from 0 to 310VAC and frequency from 40 to 500Hz or 15 to 1000Hz with the high frequency option. It is ideal for commercial, defense and aerospace test applications from design verification, quality assurance, ATEs. The AFV-P Graphical Users Interface software makes it easy to setup complex testing of the AC input to the UUT.
-
72-7265 CAL D -
Tenma
The 72-7265 CAL D from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
