Showing results: 481 - 495 of 997 items found.
-
Saluki Technology Inc.
S2107 Series Optical Cable Identifier is an intelligent instrument designed for the construction and maintenance of optical cable lines in optical communication system. In view of the complex wiring environment and the difficulty of locating faults during the construction and long-term use of optical cables, S2107 series can provide fast, effective and accurate fault solutions. When the target optical cable is bent or shaken, the optical cable census instrument can quickly capture the vibration signal and display it through waveform and sound, so as to locate the target optical cable quickly.
-
VHD -
Veer Electronics
Veer Electronics make Holiday Detector is capable to test various insulative coatings like Coal tar, Paint etc. It generates high Voltage DC for testing. When this Voltage is applied to the coated area and if pinhole or any defective point of coating is detected high voltage spark occurs on pipe or surface where we are testing. At the same time, an electronic Buzzer also beeps which gives Audio indication as well as Red colour Fault LED also glows as Visual indiction of fault.
-
AUTO DIAGNOSTECH LTD
The Sensor Imitator Probe is mainly used for the simulation of the signals generated by different types of sensors in the vehicle. It can be used in all automobiles (12V/24V), to distinguish faults that lie in the sensor itself or are related to the connectors or wires.
-
BUS1000/2000 -
GE Digital Energy
The BUS 1000/2000 is a solid state, high speed protectionsystem for the detection of phase-to-phase andphase-to-ground faults on bus bar installations. It can beused to protect high voltage bus bar installations of anyvoltage.
-
CTS-6010 -
Astronics Corporation
The CTS-6010 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
SSG 3000 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
80SICON IConnect -
Tektronix, Inc.
IConnect software is the efficient, easy-to-use, and cost-effective solution for measurement-based performance evaluation of gigabit interconnect links and devices, including signal integrity analysis, impedance, S-parameter and eye diagram tests, and fault isolation.
-
95-200-001 -
Pickering Interfaces Ltd.
The 95-200-001 Plugin Breakout Module is designed to be fitted to a PXI 40-200 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-191-002 -
Pickering Interfaces Ltd.
The 95-191-002 Plugin Breakout Module is designed to be fitted to a PXI 40-191 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-190B-003 -
Pickering Interfaces Ltd.
The 95-190B-003 Plugin Breakout Module is designed to be fitted to a PXI 40-190B Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-199-004 -
Pickering Interfaces Ltd.
The 95-199-004 Plugin Breakout Module is designed to be fitted to a PXI 40-199 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-198-001 -
Pickering Interfaces Ltd.
The 95-198-001 Plugin Breakout Module is designed to be fitted to a PXI 40-198 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-196-001 -
Pickering Interfaces Ltd.
The 95-196-001 Plugin Breakout Module is designed to be fitted to a PXI 40-196 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-193-001 -
Pickering Interfaces Ltd.
The 95-193-001 Plugin Breakout Module is designed to be fitted to a PXI 40-193 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
95-194-001 -
Pickering Interfaces Ltd.
The 95-194-001 Plugin Breakout Module is designed to be fitted to a PXI 40-194 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.