-
product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5...show more -
product
Concrete Moisture Meter
Model KM 917
Kusam Electrical Industries Limited
This is precision instrument adopting HF electromagnetic waves to measure the moisture content ratio without damaging the object under test. It can be set depending on different building material to raise its measurement accuracy.
-
product
3D Electromagnetic Simulation Software
XFdtd®
A full-featured simulation solver, XFdtd outpaces other methods in efficiency as the number of unknowns increases. XF includes full-wave, static, bio-thermal, optimization, and circuit solvers to tackle a wide variety of applications, including antenna design and placement, biomedical and SAR, EMI/EMC, microwave devices, radar and scattering, automotive radar, and more. It also works with Remcom's ray-tracing products to provide thorough simulation capability at the low-, middle-, and high-end of the electromagnetic spectrum.
-
product
EMF Detector
ElectroSensor™
This EMF detector is an unparalleled value that offers fast, reliable, and user-friendly measurements of electromagnetic pollution. Since man-made alternating current (AC) is different from naturally occurring EMF, some sources say that even extended exposure of as low as 2 milliGauss may be harmful. Fortunately, once EMF sources are identified with your ElectroSensor you can moderate your distance and exposure.
-
product
Multiphysics Simulator
The COMSOL Multiphysics simulation environment facilitatesall steps in the modeling process defining your geometry, specifying your physics, meshing, solving and then post-processing your results. Model set up is quick, thanks to a number of predefined modeling interfaces for applications ranging from fluid flow and heat transfer to structural mechanics and electromagnetic analyses.
-
product
PSG Vector Signal Generator, 100 kHz to 44 GHz
E8267D
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
product
Integrated Modular Electromagnetic Modeling Suite
EM.Cube
EM.Cube® is an industry-recognized simulation suite for electromagnetic modeling of RF system engineering problems. It features several distinct simulation engines that can solve a wide range of modeling problems such as electromagnetic radiation, scattering, wave propagation in various media, coupling, interference, signal integrity, field interactions with biological systems, etc. Using EM.Cube, you can solve problems of different sizes and length scales, varying from a few microns in MEMS devices to several miles in large urban propagation scenes.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can mo...show more -
product
EMI/EMC Compliance Consulting
EMI Devices offers a broad range of consulting services in the field Electromagnetic Compatibility. Our extensive knowledge of consumer electronics and worldwide regulatory requirements allow us to design Electromagnetic Compatibility Regulatory Compliances from the start.
-
product
Consumer Electronics
Tap into new markets through international commercial licenses. We help you by offering quality inspections and product tests for TVs, digital cameras, MP3 players, and most other consumer electronics. Using individual product testing or comparative testing, we evaluate a wide range of product characteristics, such as electromagnetic compatibility, electrical safety, or audio and video quality. We also determine whether your devices meet current environmental standards, such as banned chemicals regulations and energy conservation regulations.
-
product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
product
Field Strength Analyzer
SRM-3006
Selective measurement of high frequency electromagnetic fields. Complete, easy to use test system, consisting of a base unit and measuring antennas, for non-directional detection of fields and their sources in the frequency range from 9 kHz to 6 GHz and from 24.25 GHz up to 29.50 GHz with 5G FR2 Antenna.
-
product
Handheld Digital Thickness Gauges
HC-210
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material without damaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc., both in the laboratory a...show more -
product
Standard Electromagnetic Vibrator
KD-9363-EM
King Design Industrial Co., Ltd.
The purpose of vibration testing is to make a series of controllable vibration simulation in lab, no matter generated by natural or man-made vibration environment; such as waves, tidal flaps, wind, earthquake or rain and so on. It is to test if the product is capable of sustaining the vibration environment exerted from transporting or usage along its effective life cycle; and certify the standard of design & functional requirement of product. The value of vibration testing is to confirm the ...show more -
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
High Frequency Antenna Analysis Software
XGtd®
XGtd is a general purpose ray-based electromagnetic analysis tool for assessing the effects of a vehicle or vessel on antenna radiation, predicting coupling between antennas, and predicting radar cross section (RCS). It is ideally suited for applications with higher frequencies or very large platforms where the requirements of a full physics method may exceed available computational resources.
-
product
Antennas
A specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
product
Environmental Monitoring Systems
Eurotech environmental monitoring systems are designed to provide a scalable, efficient and compact solution that integrates multiple sensors in a single, easy to deploy unit. These compact, easy to install environment monitor systems collect and analyze air quality parameters, electromagnetic fields, ionizing radiation levels and sound pollution.
-
product
Magnetfield Testers
The magnetic field tester is suitable for rapid and precise testing of electro-magnetic switches and valves. Their tip lights up to indicate the presence of permanent, DC or AC magnetic fields. Thereby, they are so sensitive that very often it is not necessary to remove covers or cladding from machines and the function check can be carried out without any setting-up time or stopping the machine.
-
product
GEOPHYSICS, SEISMIC, and ATMOSPHERICS RESEARCH RECEIVER
Type RAS-1
Called the RAS-1, the receiver is designed for ultra low and very low frequency scientific research work, including the exploration of low frequency emissions due to seismic and earth-quake activity, study of atmospheric phenomenon such as "whistlers", and low frequency Sudden Ionospheric Disturbance (SID) and electromagnetics phenomenon. The RAS-1 will receive signals from under 200 Hz. To over 250 KHz in both narrow bandwidth modes as well as broad badnwidth reception.
-
product
Digital Sensors
PMA-Series
Solar Light’s NIST-Traceable PMA-Series Digital Sensors represent the pinnacle of accuracy, durability, and selection on the market today. Our sensors measure discrete bands of the electromagnetic spectrum from the UVA, UVB, UVA+B, UVC, Visible Light, and Infrared regions. Both narrow and broad bands are available to fit any application, including germicidal requirements, environmental probes, and sensors for biologically weighted spectra (such as the erythema and CIE action spectra.) Over 135 d...show more -
product
EMC Testing
Electromagnetic compatibility (EMC) and compliance have to do with electromagnetic energy and how it may cause electromagnetic interference (EMI) or physical damage in the environment in which it operates.
-
product
EMR Testing
It is widely accepted that exposure of the human body to high levels of Electromagnetic Radiation (EMR), Electromagnetic Energy (EME) or Electromagnetic Fields (EMF) may lead to adverse health effects. To ensure the protection of personnel in the workplace and to protect members of the general public, it is essential that the EMR levels comply with relevant exposure limits set by regulators in each country.
-
product
EMC/EMI Testing
NCEE Labs has state of the art test equipment and experienced iNARTE EMC/EMI and qualified staff to provide Electromagnetic Compatibility (EMC) and Electromagnetic Interference (EMI) testing. The lab maintains accreditation to the latest FCC, CE and other international EMC/EMI standards.
-
product
Fiber Optic Strain Sensors
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
product
Metallurgy Products
Our market-leading electromagnetic stirring and braking solutions (EMS) deliver metallurgical improvements that are proven to increase productivity, end-product quality and reduce operating costs for electric arc, ladle and aluminium furnaces, as well as thick and thin slab and billet and bloom casters.
-
product
Current Transformer Tester
HTCT-300
Full-featured, can not only satisfy various CT (eg: protection, measurement and TP category) but also PT type electromagnetic unit for its excitation characteristics (ie voltage current characteristics), ratio, polarity, secondary winding resistance, secondary load, ratio deviation, angle deviation and other test requirements.
-
product
Fiber Optic Rotary Joints
Fiber Optic Rotary Joints ensure flawless high-speed data transmission even in environments with strong electromagnetic interference. They are a maintenance-free alternative that eliminates friction and/or heating between rotating and stationary components.
-
product
Smart Fieldmeter Digital
RFP-05M
Electromagnetic field monitor having flexible and expandable architecture, state of the art design with convenience and simplicity for users on a budget.
-
product
EMI/EMC Compliance Consulting
EMI Devices offers a broad range of consulting services in the field Electromagnetic Compatibility. Our extensive knowledge of consumer electronics and worldwide regulatory requirements allow us to design Electromagnetic Compatibility Regulatory Compliances from the start.