Showing results: 1 - 13 of 13 items found.
-
Digatron Power Electronics
The Electric Vehicle Battery Tester (EVT) is designed for testing traction batteries in electric vehicles or HEV batteries in hybrid electric vehicles. The EVT realizes the functions charge and discharge with freely programmable set values for current, voltage, power or resistance in test programs, as well as the registration of the corresponding measured data.
-
MCV -
Bitrode, Inc.
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
PXIe-1149.5 -
Corelis, Inc.
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
ABex AM-300 Controller -
Konrad Technologies GmbH
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
EV : ChargeCheck -
Rolec Services Ltd
The EV Industry’s Charging Station Tester of Choice. • Simulates an electric vehicle • Tests J1772 (type 1) tethered leads • Tests IEC62196 (type 2) sockets • Tests IEC61851-1 mode 3 communication compliance • Tests for correct polarity • Tests for earthing presence • Tests contactor actions.
-
ALL-TEST PRO 34 EV -
ALL-TEST Pro, LLC
The ALL-TEST PRO 34 EV™ instrument is the ONLY TOOL made for testing the special permanent magnet motors and motor/generators used in electric & hybrid vehicles. With this innovative hybrid motor magnet tester, you can test magnet motors in vehicles from a single device that provides quick and precise diagnostic results. Our patented technology enables technicians to find motor problems before they turn into costly maintenance projects.
-
98x -
Vitrek Corporation
The new 981i and 983i Teraohmmeters are designed to tackle the toughest High Resistance measurement applications. Demanding applications that most other IR testers won’t measure up to. So when it’s time to test higher voltage IR values like today’s electric vehicle systems and higher voltage solar arrays — look to Vitrek to deliver the IR tester you need for your production line.
-
EVSE LLC
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
T4350 -
The Eastern Specialty Company
With the growing demand for electric vehicles (EV), there needs to be a simple and accurate method to test EV charging systems. Test the accuracy of AC and DC voltages and currents with TESCO’s Electric Vehicle Service Equipment (EVSE) Test System TS400. The TS400 is a valuable set with complete testing capabilities and caters to every possible EVSE charging protocol in the world (AC and DC). EV charging stations are popping up all over as the sale of electric vehicles increase. Many states or counties are now mandating testing for these charging stations. TESCO’s TS400 makes testing these chargers easy! TESCO’s EVSE Test Systems test the accuracy of energy delivery using a transactional mode compatible with Handbook 44 provisions. The TS400 Test System includes a T4000 EVSE Tester and a PL4000 EV Load Emulator. Reach out to your TESCO Representative for more information!
-
767943 -
Wesbar
Plug these testers into any car connector and you will have an instant test of running light circuits. Features LED display to show completed circuit for the running lights left turn signal and right turn signal. Auxiliary and electric brake circuit are included on the 6-way tester and auxiliary, electric brake and battery charge are included with the 7-way tester. One piece units with internal ground. Proper installation and set-up of a brake control, when a trailer is not readily available, is possible with the 7-way tester. Current Monitor testing device is designed to assist in determining whether a tow vehicle's 7-way blade car end connector has been wired properly. (Current Monitor is an excellent diagnostic tool for installation, setup and troubleshooting of electric trailer brake controls.) The Trailer Tester is designed to help you quickly identify problems in the wiring of the trailer. This is done by testing the Left Turn, Right Turn, Tail/Marker, Brake and Back Up circuits on the trailer. The tester indicates approximate amount of current in each circuit (i.e. trailer battery). Brake Control Bench Tester is a test device designed to determine if a brake control is working properly. Checks brake control output, independent of vehicle wiring. Simulates many fault conditions including open ground, short circuit, open load and more.
-
NuVant Systems, Inc.
Our line of HEV / EV Battery Equipment combines sophisticated electronics, advanced technology, and user-friendly operation. The EVc Battery Reconditioner processes all types of nickel metal hydride HEV batteries. Worldwide, the EVc has proven to be a neccesary workhorse for any hybrid auto shop or garage. The EVd Power Tester monitors individual module voltages during high power battery discharge. The EVd also features a "smart" charger that performs complex CCCV charging. We are currently developing technology to process and rebalance the Li-ion batteries for electric vehicles.
-
IT5100 Series -
I-TECH Electronic Co., Ltd
IT5100 series is a series of battery internal resistance testers with high precision, high resolution and high speed. IT5100 adopts AC 4-terminal sensing, that means the tester can test internal resistance and voltage simultaneously with high precision. Resistance resolution is down to 0.1 μΩ, voltage resolution is 10 μV. Combined with external USB disk, IT5100 is available for long-term statistics calculation.Built-in comparator function, IT5100 can automatically determine whether the battery parameters meet the standards and count pass rate, which is suitable for a variety of battery`s test and pick. Built-in GPIB / USB / LAN communication interface to support SCPI communication protocol.Single unit of IT5102 support 16 channels batteries measurement, master- slave connection up to max.17 sets and extension channels quantity up to 272, that greatly improves testing efficiency. Built-in LAN / RS232 communication interface, IT5100 series can be widely applied in cellphone lithium batteries,electric vehicle batteries and other batteries inspection and sorting.
