ESD
ESD Testing Equipment includes Surface Resistance/Resistivity Meter, Electrostatic Field Meter, Wrist Strap Checker, and Constant Wrist Strap Monitors.
See Also: ESD Test, Surface Resistivity
-
Product
Electronic System Design
ESD
-
Smart connected devices are everywhere, in homes, in transportation, and at work. This means electronic system design (ESD) is having a greater influence on almost every type of product requiring new simulation tools to help achieve electronic, electrical, mechanical, thermal, and connectivity goals. Altair’s simulation-driven design tools enable your team of specialized engineers to collaborate across all aspects of printed circuit board development from concept to manufacturing. Our products streamline your process, eliminate design iterations, and reduce time-to-market.
-
Product
.13u ESD diode
Impulse TSMC
-
The Impulse TSMC .13u ESD diode was made to provide ESD discharge paths when integrating third party IP in an integrated circuit design for total ESD protection. The Impulse ESD diode has been successfully used with Dolphin Technologies, Artisan/ARM, TriCN/Synopsis I/O libraries, as well as popular IP blocks from RAMBUS, Chip Idea and other quality IP vendors. A 5.5 volt reverse bias anode to cathode operational specification enables the Impulse TSMC .13u ESD diode to be the device of choice for 5 volt tolerant designs.
-
Product
Portable Touchplate Wrist Strap Tester
-
Testing your ESD Wrist Strap system before handling electrostatic sensitive is extremely important. ESD events can go unnoticed by feel and sight. While a static discharge into a door knob (we’ve all done it!) can be thousands of volts, an ESD event can be as little as 10V, and you will not feel this. This is a no-frills, “go-no-go” type tester, but portable. Sure you could put this at your entry point, but where it really shines is in special remote applications. Keep one in your tool box, bag or Field Service Kit.
-
Product
LD/LED ESD Tester
-
Hanwa Electronic Ind. Co.,Ltd.
Performs automatic destructive evaluation of Lazer-Power.
-
Product
Transceiver Module
-
Mornsun Guangzhou Science & Technology
MORNSUN transceiver modules include integrated high efficiency CAN, RS485, RS232 isolated transceiver module, protocol conversion module and serial port to ethernet transceiver module. These industrial bus transceiver with DIP, SMD, SOIC and DFN optional packages features compact size, surge and ESD bus protection, a maximum isolation voltage up to 5,000 VDC and a wide operating temperature range of -40°C to 85°C, even up to 105°C, etc. Coupled with the use of IC integrated technology, the isolated transceiver module can easily be embedded in the user's end equipment, and achieve fully-functional bus network connectivity and data communication. Check out these isolated transceiver modules with a reasonable price along with high performance and we hope that they are an ideal fit for your application needs.
-
Product
Interface
-
Renesas offers industry-leading devices to enable efficient and reliable communication for industrial control, networking and computing applications. Dual protocol transceivers, voltage level translators, I2C Buffers, wide operating voltage range RS-232 transceivers, and RS-485/422 devices with the highest noise immunity and ESD protection in small packages are available to support high-speed data transfer and a variety of configurations to fit your applications.
-
Product
ESD SURFACE RESISTIVITY METER (WITH 10 LEDS)
-
Simply place the meter on the surface of the material that requires measuring.Press the green test button. The meter will then light the appropriate LED from 10 to the power of 3 to 10 to the power of 12 Ohms per square or insulative.
-
Product
Transmission Line Pulse Testing
-
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
-
Product
ESD Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
Product
ESD Testing
-
MicroStat Laboratories -R.E.T.S.
A leading independent ESD test company, MicroStat Laboratories/River’s Edge Technical Service maintains a fully equipped ESD test laboratory committed to the testing and evaluation of products, materials, and processes used in electrostatic discharge (ESD) control.
-
Product
7th Gen. Intel® Core™ Processor-Based Fanless Open Frame Touch Panel PC
SP2-KL Series
Panel PC
- 7th Gen. Intel® Core™ Proc- 10.1"/15.6"/21.5" PCAP touch screen- Wide input voltage range 9-36V DC- Full customization for fast integration with all form factors, kiosks, and all-in-one panel PC applications- Enhanced protection in case of sudden power outage with back-up battery (Optional)- Pre-compliance EMC testing and high ESD tolerance
-
Product
RS-232
-
Renesas' RS-232 transceivers are available in many configurations and feature data rates up to 1Mbps, IEC61000 ESD protection, low power shut down modes, and small QFN packages.
-
Product
Plant Auditor's Surface Resistance Kit
PMK-153
-
The PMK-153 Resistance Test Kit contains the instruments you need to take resistance measurements.The PMK-153 includes the PAS-853B Wide Range Ohmmeter with 5 pound Conductive Rubber Electrodes. The PAS-853B instrument is a wide range ohmmeter that measures accurately from 0.01 to 9.9x1012 ohms. In AUTO mode the instrument automatically adjusts resistance range and selects test voltage in accordance with standard practices outlined in ANSI/ESD STM11.11, and meets audit requirements of ESD TR53.
-
Product
Ohm-Stat Guardian Constant Monitor
-
Tests one person and one wriststrapRed and green LED and fail buzzerNIST calibration includedWorks with single wire capacitance wriststrapsCE markCan be calibrated110v AC adapter or 9v battery poweredIdeal for in plant or field service workProduct conforms to the ESD S.20.20 spec standardsGround dock includedLow cost
-
Product
ESD CONTINUOUS DUAL OPERATOR WRIST STRAP MONITOR
-
This economical continuous wrist strap monitor ensures that your wrist strap is in good working condition. Ensure wrist strap in good working condition
-
Product
Dissolved Carbon Dioxide (DI-CO2) Ultrapure Water Delivery System
-
The DI-CO2 is used in single substrate cleaning tools for rinsing steps to prevent ESD effects and/or corrosion by creating UPW (ultrapure water) with precisely defined conductivity. It is a compact system for tool integration, providing conductive DI-CO2 water (Carbon Dioxide) with closed loop controlled conductivity. The conductivity is kept at a constant value under changing flow conditions by control of the CO2 concentration in the DI-CO2 water.
-
Product
Wide Range Ohmmeter
PAS-853B
-
- Wide Resistance Measurement Range from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period Control- Automatic or Continuous Electrification ControlRugged High Performance 80 inches (200cm) Test Leads Included- Powered by one long lasting 9V Alkaline Battery- Large, Easy to Read LCD Display- Meets requirements of ESD Association Standards for material and audit resistance measurement requirements- Certificate of Calibration Traceable to NIST included
-
Product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
-
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
-
Product
ESD Tester
PurePulse
-
PurePulse is a flexible and efficient ESD tester for HBM, TLP, MM and HMM. Its 2-pin style setup reduces tester parasitics, it captures waveform data and can be automated to test thousands of pins without the need for a test fixture. Our PurePulse system was designed from the ground up to be customized to meet your testing needs, take a look at the features below and schedule a demo with us to learn more.
-
Product
Stereo Zoom Trinocular Microscope
SPZV-50E
-
SPZV-50E Stereo Zoom Trinocular Microscope 6.7x to 50x, max 200x with optional lenses on stand PLED with 60 eco friendly LED lights with dimmer. Attach any C or C/S mount camera to the trinocular port to view images on a monitor. Focus mount has coarse and fine focusing for precise control. Large 200 x 284mm base. Compact footprint helps save bench space. ESD Safe coating protects sensitive components from electrostatic discharge.
-
Product
ESD & Latch-Up Test Service
-
MASER Engineering has automatic test equipment for the most common ESD test pulse models. MIL - JEDEC - ESDA - IEC standards. IC level Human Body Model. IC level Machine Model. IC level Charged Device Model. System level IEC 61000 HBM. AEC-Q100 Field Induced Gate Leakage test. Static Latch-Up test. Dynamic Latch-Up test.
-
Product
X-Band Silicon Radar Quad Core IC
AWS-0105
-
The AWS-0105 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and single beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
Product
BF-Series Standard Models
-
The E-DRIV® BF-Series standard models feature an adjustable RPM setting on the tool and a selectable Soft Start mode. Engineered for high volume manufacturing applications the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
High Voltage Op Amplifiers ≥12V
-
High supply voltage op amps are used in systems that demand the widest dynamic range with the best signal-to-noise ratio. Engineers turn to Analog Devices for high voltage amplifiers that deliver industry-leading performance. Increasingly, new high voltage amplifiers also offer features to improve system performance, cost, and robustness while easing the complexity of system design. New features include integrated input overvoltage protection (OVP), on-chip electromagnetic interference (EMI) filtering, higher electrostatic discharge (ESD) immunity, and greater resistance to latch-up in both powered and unpowered operations.
-
Product
Pulsed IV-Curve Solutions
-
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
Product
Assembly & Test Services
-
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
Product
4-Port RS-232/422/485 Serial Device Server
EKI-1524
-
Provides 2 x 10/100 Mbps Ethernet ports for LAN redundancyProvides COM port redirection (Virtual COM), TCP and UDP operation modesSupports up to 921.6 kbps, and any baud rate settingAllows a max. of 5 hosts to access one serial portAllows a max. of 16 hosts to be accessed as TCP client modeBuilt-in 15 KV ESD protection for all serial signalsProvides rich configuration methods including Windows utility, Telnet console, and Web BrowserSupports 32-bit/64-bit Windows 2000/XP/Vista/7/8/8.1/10, Windows Server2003/2008/2012/2016, and LinuxAutomatic RS-485 data flow controlSupports line to line 2 KV, line to ground 4 KV surge protection
-
Product
Static Charge Event Detector / Data Logging System
EV-10A
-
Tokyo Electronics Trading Co., Ltd.
EV-10A detects ESD (Electro-Static Discharge) and records them in a PC. ESD sensitive electronic components increase rapidly. If electro-static charge is not strictly controlled in the production line of these components or in the assemble line using them, the yield will be decreased.
