-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-114
Precision Resistor Module
The 40-297A-114 (PXI) and the 42-297A-114 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 470 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-034
Programmable Resistor Module
The 40-297A-034 (PXI) and the 42-297A-034 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 2m, 250 Port
A500RMR-T-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PXI High Density Multiplexer, 1-Bank, 80-Channel, 2-Pole
40-615A-012
Multiplexer Module
The 40-615A-012 is a 1-bank, 80-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI 18 Channel Power Mux 1 Pole
40-665-001
Multiplexer Module
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
-
Product
Underwater Quantum/PAR Sensors
-
Photosynthetic radiation is essential for the growth of the photosynthetic organisms such as corals. The wavelength range from 400 to 700 nm is PAR (Photosynthetically Active Radiation) or PPFD (Photosynthetic Photon Flux Density). Apogee quantum/PAR sensors are calibrated to measure the number of photons of light across this range.
-
Product
PXI 12-Slot BRIC Matrix, 198x8 1-Pole (9 sub-cards)
40-562B-321-198X8
Matrix Switch Module
The 40-562B-321-198X8 is a high density BRIC12 matrix module with a size of 198x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 66x16 1-Pole (6 sub-cards)
40-562B-321-66X16
Matrix Switch Module
The 40-562B-321-66X16 is a high density BRIC12 matrix module with a size of 66x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
25-pin D-type Connector & Cable Accessories
-
Our Standard Voltage 25-Pin D-Type connector is used on PXI and LXI switching products to provide a medium density user connector solution.
-
Product
Automated Bare Board Tester with Built-In Camera
QTOUCH2404C
-
Qmax Test Technologies Pvt. Ltd.
Qtouch2404C – Automated Bare Board Tester with in-built camera is designed to make automatic image capturing and probing of bare PCBs. It is designed to move on X,Y,Z directions making it possible to probe every test point. Flying Probe Tester is designed for testing high density fine pitched Single Sided / Double Sided and Multilayer PCBs for continuity and isolation using moving probes fixture –less technology.
-
Product
PXI/PXIe RF Matrix, 16x2, 300 MHz, 50 Ω MS-M Multiway With Loop-thru
42-728A-002-L
Matrix Switch Module
The 40-728A-002-L (PXI) and 42-728A-002-L (PXIe) are 16x2 50 Ω RF matrices with MS-M Multiway connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
VXI Series
-
The first VXIbus specification was introduced to the test and measurement community in 1987 and was initially developed to provide a card-based instrumentation platform for applications that required high density and high performance. The platform continues to thrive today by leveraging off the original specifications which define the necessary physical (real estate/cooling) and electrical standards for demanding applications and has established itself as the ‘time-tested bus you can trust’ for requirements that must be supported in excess of ten-fifteen years.
-
Product
PXI 2-Slot BRIC Matrix, 10x32 1-Pole (2 Sub-cards)
40-562B-221-10X32
Matrix Switch Module
The 40-562B-221-10X32 is a high density BRIC2 matrix module with a size of 10x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 60x8 2-Pole (2 sub-cards)
40-561A-122-60X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
40 Channel Single-Ended Multiplexer Module for 34970A/34972A
34908A
Multiplexer Module
Use the Keysight 34908A module for the 34970A/34972A Data Acquisition/Switch Unit for the greatest density in common-low applications, such as battery test, component characterization, and benchtop testing. Each module switches 40 one-wire inputs. All two-wire internal measurements except current are supported. The module low connection is isolated from earth and can float up to 300 V.
-
Product
PXI High Density Screened Mux 5 Ch 16 Pole
40-670A-021-S-5/16
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI 2A Multiplexer, 2-Bank, 16-Channel, 4-Pole
40-614B-012
Multiplexer Module
This 2-bank, 16-channel, 4-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 6.97kΩ
40-298-024
Programmable Resistor Module
The 40-298-024 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe High Density Reed Relay Module, 100xSPST
42-140-221
Reed Relay
The 40-140B-221 (PXI) and 42-140B-221 (PXIe) are 100xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI 8 Slot BRIC 90x8 1-Pole (3 sub-cards)
40-561A-121-90X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-144
Precision Resistor Module
The 40-297A-144 (PXI) and the 42-297A-144 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 1.51 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 12-Slot BRIC Matrix, 704x4 2-Pole (16 sub-cards)
40-562B-322-704X4
Matrix Switch Module
The 40-562B-322-704X4 is a high density BRIC12 matrix module with a size of 704x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 210x8 1-Pole (7 sub-cards)
40-561A-121-210X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode
40-852A-018
Multiplexer Module
The 40/42-852A-018 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Density Determination and Bulk Density
-
Consisting of 2 incremental displacement transducers 25 x 0.01 mm (measurement of volume change over path) with interface for connecting the displacement transducers with RS 232 C interface for PC, complete with Windows software with real-time display of uplift over time including trial database and option for log output.
-
Product
PXI 4-Slot High Density 2A BRIC Matrix, 58x8 2-Pole (2 Sub-cards)
40-573-002-58X8
Matrix Switch Module
The 40-573-002-58x8 BRIC is part of a range of high density matrix modules able to switch up to 2 A at 240 VDC/250 VAC. They are available in 2, 4 or 8-slot sizes to suit most high performance matrix requirements, constructed using quality electromechanical relays for high switching confidence.
-
Product
LXI High Density 50x64 2A Matrix With BIRST
60-552-922
Matrix Switch Module
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 4-Channel, 32-Pole
42-614D-020
Multiplexer Module
The 40-614D-020 (PXI) and 42-614D-020 (PXIe) 1-bank, 4-channel, 32-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 8-Slot BRIC Matrix, 138x8, 1-Pole (3 sub-cards) Dual Bus
40-560B-121-138X8-M
Matrix Switch Module
The 40-560B-121-138x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
Product
PXI Solid State Versatile Multiplexer
40-683-001
Multiplexer Module
The 40-683 Very High Density Versatile Multiplexer module features a wide range of selectable switching configurations. The 40-683 is especially useful where a high density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future. The 40-683 uses high performance solid state switching to ensure a service life of greater than 10 years and fast operation.
