-
Product
PXI Very High Density Multiplexer, 99-Channel, 2-Pole
40-675B-002-99/2
Multiplexer Module
The 40-675B-002-99/2 (PXI) and the 42-675B-002-99/2 (PXIe) are 99-channel, 2-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
Product
Circbord
8015-1
-
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole pattern one side only.0.080” diameter isolated solder pad around each hole one side only.Unrestricted component placement and extended area for high density applications.
-
Product
PXI 2A Multiplexer, 4-Bank, 4-Channel 8-Pole
40-614-009
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI 2 Slot BRIC 58x6 2A 1-Pole Matrix
40-596-201
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
Magnetic Field and Permeability Measurement
MAGNETOSCOP® 1.070
-
Foerster Instruments, Incorporated
The MAGNETOSCOP 1.070 is a portable magnetometer system with microprocessor and probes for measuring the magnetic flux density as an absolute or differential value (gradient). It has a USB port for simple data transfer and an SD card for saving measurement data and parameters. The measuring system also facilitates the recognition and saving of peak values and the adjustment of thresholds for limit values. The unit can be used for series and individual measurements. The data can be easily analyzed and documented with the PC software included in the scope of delivery. The MAGNETOSCOP 1.070 thus facilitates the portable and fast measurement of the relative permeability within the scope of the quality control of stainless steel and low-permeable (non-magnetic) alloys as well as the localization of ferrite enclosures. Changes in material (sulfidation, degradation of lamination, structural changes) can also be proven thanks to permeability comparative measurements.
-
Product
Counter/Timer Function Cards
ProDAQ 3800 Series
-
The ProDAQ 3800 Series counter/timer function cards are high-density cards that fit into ProDAQ VXIbus motherboards and LXI function card carriers. ProDAQ instruments are versatile, providing users with the highest channel density and functionality available on the market.
-
Product
PXI 4-Slot BRIC Matrix, 2A 1-Pole 176x8, 4 Sub-cards
40-567A-004
Matrix Switch Module
The 40-567A-004 is a PXI 1-pole 176x8 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 100VDC/70VAC. The 40-567A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
MTCA 4.0 1000W PS
-
The WIENER MTCA.4 is a low noise and ripple / high power density power supply in a double height / double width form factor. Designed according to the PICMIC MTCA-4 standard it provides 1000W for 12V payload power as well as 3.3V management power.
-
Product
PXI High Density Multiplexer, 2-Bank, 32-Channel, 2-Pole
40-610A-007
Multiplexer Module
The 40-610A-007 is a 2-bank, 32-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 2A Multiplexer, 2-Bank, 4-Channel 16-Pole
40-614-014
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
TeraBox FPGA Servers
-
At the extreme of FPGA server density, the TeraBox 1401B/1402B give the highest level of compute and network capability in a 1U chassis. These servers provides twice the density of the typical 4U server. These innovative products support PCIe Gen4 and feature an AMD EPYC or Intel Xeon processor in a standard rack depth chassis.
-
Product
PXI 8-Slot BRIC Matrix, 110x8 1-Pole (5 sub-cards)
40-562B-121-110X8
Matrix Switch Module
The 40-562B-121-110X8 is a high density BRIC8 matrix module with a size of 110x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PCI Express Card with 96 DIO and Counter/Timers
PCIe-DIO-96C3
-
This is a x1 lane PCIe, 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length slot that has x1 lane PCIe.
-
Product
Power Supply 1950W
PS236 / CS236 1100W
-
The high density high sophisticated PS236 power supply series replaces the well used PS336 types. PS236 is only 3U high and features six separately regulated extremely low noise outputs for use in CAMAC crates conforming EUR 4100 as well as CERN EP82-01 / EP84-01 and 46-04 specifications as well as in NIM bins UEN01 HC 12.
-
Product
PXI Ultra High Density Matrix, 84x4, 1-Pole, 2A, 60W
40-575A-001
Matrix Switch Module
The 40-575A-001 is a high density matrix module able to switch up to 2 A or 300 VDC/250 VAC. It is in 84x4 1-pole configuration and constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI BRIC4 FIBO Matrix Dual 60x4 3pin brkout
40-592A-003
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Ozone Generators & Systems
-
MKS offers a wide range of ozone generators and modular delivery systems which produce ultra-pure, reliable ozone gas. In the clean semiconductor environment, Ozone reacts with a wide range of precursor gases resulting in the creation of Al2O3, ZrO2, HfO2, and La2O3 metal oxides to enable thin film deposition processes like Atomic Layer Deposition (ALD) and Etch (ALE). MKS’ generator uses Grade 6 gas, enabling the creation of higher film density improving product yield. Photovoltaic and Display manufacturing leverage semiconductor best practices and utilize ozone to create enhanced thin film barriers, improving product performance and reliability.
-
Product
PXI 8 Slot BRIC 484x4 1-Pole (11 sub-cards)
40-562A-121-484X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
High Resolution Wavefront Sensor
-
Phasics wavefront sensor applies to laser beam measurement, wavefront correction through an adaptive optics loop, laser optics testing and plasma density measurement. Thus the single instrument offers true versatility to engineers and researchers in laser facility.
-
Product
LXI High Density 56x64 2A Matrix With BIRST
60-552-026
Matrix Switch Module
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω MS-M Multiway
40-729A-002
Matrix Switch Module
The 40-729A-001 (PXI) and 42-729A-001 (PXIe) are 8x4 50 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
-
Product
PXI 2 Amp Multiplexer, 4-Bank, 16-Channel, 1-Pole
40-657A-001-4/16/1
Multiplexer Module
The 40-657A-001-4/16/1 is a 4-bank, 16-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
PXI 8-Slot BRIC 120x8 Matrix, 2A 2-Pole (5 sub cards)
40-565A-102-120X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-518-M62.5-HI
Multiplexer Module
The 40/42-852A-518-M62.5-HI is a PXI/PXIe 8-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI 8-Slot BRIC Matrix, 484x4 2-Pole (11 sub-cards)
40-562B-122-484X4
Matrix Switch Module
The 40-562B-122-484X4 is a high density BRIC8 matrix module with a size of 484x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 2A Multiplexer, 2-Bank, 16-Channel, 4-Pole
40-614C-012
Multiplexer Module
This 2-bank, 16-channel, 4 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 2 Amp MUX, Single 32-Channel 1-Pole
40-635-101
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 12-Slot BRIC Matrix, 85x32 1-Pole (17 sub-cards)
40-562B-321-85X32
Matrix Switch Module
The 40-562B-321-85X32 is a high density BRIC12 matrix module with a size of 85x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Solution Dispenser
1550A
-
The CHI1550A solution dispenser is designed for making high density and high accuracy solution arrays. Solution arrays are widely used in chemical, biological and medical applications. The solution dispenser consists of a high resolution three dimensional positioner, a piezoelectric jetting device, and a sample platform.
