Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
product
Clamp type AC Current Sensor/with DC Voltage Output
ACT-5H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 0.1A~5A*DC 5V full scale output
-
product
Leakage Current Clamp Mete
Basic functions:AC current:20mA resolution: 0.01mA, ± (2.5%, +5)200mA resolution: 0.1mA, ±(2.5%, +5)2A resolution: 1mA, ±(2.5%, +5)60A resolution: 100mA, ±(3%, +8)AC voltage: 600V, ±(0.8%, +5)DC voltage: 600V, ±(0.8%, +5)Special functions:Auto ranging Low battery display Data hold Auto power-off Over-load protection Input impedanceDC voltage measurement: ≥10MΩ Sampling frequency: 3 times/s Maximum display: 1999 Maximum distance between clamps: 30mm General characteristics:Product colors: iron-gray and redProduct net weight: approximately 136gLCD size: 25x36mmProduct size: 183x63x29mmPower: 2x1.5V, 7#Standard accessories: packing carton and handheld bag English user's manual and battery
-
product
DC In AC Clamp Tester
M-800P
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Model 800P is the world’s first clamp meter which can detect smallDC current in AC circuit in addition to general AC/DC current measurement.*By using this clamp meter, DC offset surveillance can be madeeasily in the actual fields like as solar inverters, etc. and it is possibleto check if the DC component in AC circuit is less than 1% ofthe rated AC current or not, according to the regulation.
-
product
Precision Picoprobe™ Micropositioner Probe Holder Kit
PHD-3001A
High Power Pulse Instruments GmbH
*Pulse force and pulse sense fixed pitch and flexible pitch RF probing solution for TLP/VF-TLP/HMM on-wafer measurements using Picoprobe™ Model 10*High peak current capability 80 A (100 ns)*DC – typ. 7 GHz bandwidth*Isolated probe-head ground shield for high pulse sense common mode signal rejection*Including fixed pitch replacement probe tip 50 Ω, right, 100 µm pad pitch*Including fixed pitch replacement probe tip 5 kΩ, left, 100 µm pad pitch*Including flexible pitch clamps plus 10-5k(0502)-125-W-1 and 10-50/30-125-W-1 replacement probe tips*True coaxial high-resolution 80:1 rotary probe-head for accurate probe tip adjustment
-
product
Clamp Meters
Our clamp meters measure both high and low AC and DC currents as well as earth leakage and earth resistance. With variable jaw sizes, max current readings up to 2000A AC/DC and features including TRMS, data logging and temperature readings we have clamps suitable for a wide range of electrical applications.
-
product
AC/DC Flexible Leakage/Line Current Probe
FAD-100
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Long Time Record of Measurement by Input Power Supply・Detection of Both AC Current and DC Current At Once・Detection of Small DC current Inside Large AC Current・Freely Bending with Flexible Clamp Sensor of Inside Diameter 200mm・Useful for difficult Access Locations with Wide Ranges up to AC/DC 1000A
-
product
Voltage logger0 to 2.5V
TK-4703
Supplied with an input cable, this logger can measure voltages up to 2.5V DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.The unit is particularly useful when space is at a premium.
-
product
Current Clamps
A versatile clamp with a capacity to measure very low AC and DC currents, from a few milliamps and equipped with multiple measurement possibilities: voltages, resistances, frequencies, fast continuity, capacitance, temperature.
-
product
Micro-Ohmmeters
RMO-G Series
The RMO-G is a portable micro-ohmmeter designed for contact resistance measurement of non-inductive test objects and applications with increased safety requirement. It tests medium and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. Due to its Both Sides Grounded and Remote Control functionalities, the instrument accurately measures even in the most demanding environments, providing additional safety to testing personnel.The RMO800G is the most powerful portable micro-ohmmeter on the market with 800 A output current. RMO200G is our best seller in the USA. A user can choose the appropriate model depending on the output current requirement, from 100 A (RMO100G) to 800 A (RMO800G).We use an unbreakable plastic case with IP67 protective rating (with closed lid) for instruments’ housing. Although very portable and lightweight, RMO-G micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents. Consequently, it enables the usage of thinner/longer test cables. RMO-G generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. During the testing, it increases current before measuring and decreases current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.Special current clamps measure a current through groundings when the instrument tests in Both Sides Grounded conditions. The instrument itself powers these clamps. If even higher safety level is required, the Remote Control feature enables the operator to perform measurements from distant locations.RMO-G instruments can store up to 500 measurements in internal memory. Also, they have a built-in thermal printer and USB flash drive available as an option. An additional option is the built-in High Precision module suitable for measurement of very low resistance, in the range from 1 to 30 µΩ, with 0,01 µΩ resolution.Our free DV Win software communicates with the RMO-G micro-ohmmeters via USB or RS232 interface. It allows a user to run the test remotely from a PC. Also, a user can download test results, analyze and generate fully configurable test reports through the software.
-
product
AC/DC Mini Digital Clamp Tester (CE)
M-280
MULTI MEASURING INSTRUMENTS Co., Ltd.
*30mmφ CT window and ultra compact size.*Conform to IEC safety requirements.*Low cost and multi-function clamp tester.*Max. and Min.hold function.*Data-hold function and auto power off.*Auto zero adjustment for DC current offset.
-
product
Solar PV Test Equipment
Di-log offer a comprehensive range of Solar PV test equipment and tools to service the renewable industry. The range offers irradiance meters, DC current clamp , meters, crimp tools, roof surveying and protective gloves.
-
product
1000 Amp AC/DC Digital Clamp Meter
DL6402
With inclusion of DC current temperature & capacitance readings, this clamp meter is the ideal all purpose instrument.The slim design combined with the tear shaped jaw makes it an ideal unit for use in crowded panels and tight spaces.The data hold and peak capture function makes this a versatile and cost effective clamp meter.
-
product
1000A AC/DC Clamp Meter
CM84
The CM84 is a high specification 1000A clamp meter, packed full of functions for the installation, testing and maintenance of domestic and industrial installations. It is light enough for easy one handed operation but still robust enough for use in harsh environments.
This compact meter provides accurate measurement of AC voltage to 750V, DC voltage to 1000V and AC current to 1000A. It has the same test functions you would find on a high specification multimeter making this clamp a comprehensive testing solution for electricians, maintenance and service engineers. This has the added benefit of DC current measurement to 1000A and has a useful DC current zero function.
-
product
AC/DC Current Clamp Probe,DC~500kHz(-3db)
CP-07
Can connect with Oscilloscope. AC/DC current Measurement. 400mA ,2us, 4A,2us test range. Bandwidth: DC~500kHz(-3db)Rise time:1.5μsNoise level: ≤4mA(with average mode) or ≤20mA(DC~500KHz)Jaw size: 5mm max. Auto zero at power on. Relative zero correction.
-
product
Current Clamp Meter
CP 41
The CP 41 current clamp meter has been designed for reliable and accurate, non-intrusive measurement of AC, DC and complex waveform currents. Using advanced Hall Effect technology the CP 41 can measure currents accurately from 5mA to 40Amps.
-
product
AC/DC Current Clamp Probe,DC~5MHz(-3db)
CP-07C
●Connect to Oscilloscope.●AC/DC current Measurement.●Bandwidth: DC~5MHz(-3db). ●Rise time:0.7μs●Noise level: 10mA●Jaw size: 5mm max.●Auto zero at power on.●Relative zero correction.
-
product
Ammeter According to DIN EN 61010-1 (VDE 0411-1)
PeakTech Prüf- und Messtechnik GmbH
Is a measuring device for AC and DC currents up to 1000 A using a current clamp for conductor diameters up to 48 mm. Current and voltage measurements are carried out as true RMS (true rms value) measurements, which means that the measured values are displayed correctly even with waveforms that deviate from a sine wave.
-
product
AC/DC Hall Effect Sensors
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
product
AC/DC Current Clamp Probe,DC~1MHz(-3db)
CP-07+
Can connect with Oscilloscope.AC/DC current Measurement.1mA to 4A test range.Bandwidth: DC~1MHz(-3db).Rise time:0.35μsNoise level: 2mAJaw size: 5mm max.Auto zero at power on.Relative zero correction.
-
product
Clamp type AC Current Sensor/with DC Voltage Output
ACT-50H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 1A~50A*DC 5V full scale output
-
product
True RMS Low Current Clamp Meter
688
CLAMP METER We’ve greatly improved the zero drift on the low DC amps function - along with enlarging the clamp size to accomodate larger ground cables. The significant amount of feedback from our end user customers has contributed greatly in building this premium low current clamp meter. These features will be unmatched. Great tool for parasitic drain testing.
-
product
Current logger0 to 20mA
TK-4802
Supplied with an input cable, this logger can measure current between 0 and 20mA DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.
-
product
Current Detectors
On our website you will find current detectors that are ideal for measuring AC or DC voltage. Current detectors are irreplaceable for inspection work and maintenance. We offer the following: voltage detectors, voltage leak detectors, voltage power detectors, Current clamps ideal for measuring AC or DC voltage. metric detectors, current detectors and more. These high quality current detectors include the capacity to measure many other parameters, such as capacity, resistance, power (both by way of clamps or by means of a hand held digital device with external clamps with a range of one or three stages). The current detectors are like the majority of our measurement instruments in that they meet and excel ISO standards. This calibration is done in a laboratory and comes with an accompanying certificate. All of our current detectors can perform the demanding tasks in each industrial sector regardless of the technical problem you encounter. If you can't find the current detectors you are looking for, please contact us and we will help you find the best solution to suit your needs by calling our offices on: UK customers +44(0) 23 809 870 30 / US customers (561) 320-9162 and our technical staff will advise you regarding our measuring instruments. Our engineers and technicians will be happy to help you with the current
-
product
Ground Grid Tester
GGT Series
The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.
-
product
DC/AC Current Clamp Probe,DC~30KHz(-3db)
CP-07A
Range: 40mA,7us,400mA,7usBandwidth: DC~30KHz(-3db)Noise level: 2mA Rise time:10μsEarth magnetic proofBNC socket for connect to oscilloscopeLow noise,low currentExtremely low current from 100µADimensions: 215mm(L)× 58mm(W)× 36mm(H) Weight: 200g
-
product
AC/DC TRMS Insulation Clamp Meter
CMi210
A unique insulation clamp meter for the installation, testing and maintenance of domestic and industrial installations. This high specification clamp meter can perform insulation tests to 6G Ohms with 5 test voltages from 50V to 1000V.
The clamp provides True RMS measurement of AC current to 1500A and AC voltage to 750V. It will also measure DC current to 2000A and DC voltage to 1000V. The CMi210 has all the same test functions you would expect to find on a high specification multimeter with the added benefit of temperature measurement.
-
product
Clamp Meters
The clamp meter is ideal for measuring AC or DC voltage. The instrument is irreplaceable for inspection work and maintenance in various industrial applications, in research and development, in residential applications and in many small businesses or households. The PCE line of clamp meter is made according to the highest industry standards and very important: PCE offers instruments that are usable in all workspaces (equipped with very small or even very large jaws), the results are reliable and the clamps are easy to use. Every clamp meter is manufacturer calibrated and can be certified to ISO or NIST - hold a PCE clamp meter in your hands and you can feel the quality immediately.PCE offers a variety of models: Voltage detector, voltage leak detector, voltage power detector, metric detector and current detector. In addition many clamp meters are able to measure other parameters, such as capacity, resistance and power - power through clamps directly or by handheld digital instruments with external clamps (with a range of one or three stages). Very often the clamp meter is a real multimeter - so it becomes a general electrical measurement tool.
-
product
Clamp-on DC Meters
The Swain Meter™ Company manufactures portable clamp on DC ammeters that precisely measure the magnitude and direction of DC current flow on any conductor. Used both onshore and offshore, Swain DC clamp on amp meters accurately read current from 5mA to 200 Amps with a resolution of 1mA in the 0-2Amp range.
-
product
Clamp type AC Current Sensor/with DC Voltage Output
RCT-18
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements with DCV output for recorder*AC 0.1mA~100mA
-
product
Clamp Meters
oltage DC 600V with basic accuracy ±(0.5%+5d)Voltage AC 600V with basic accuracy ±(0.8%+5d)Current AC 400V with basic accuracy ±(2.50%+6d)Slimline Electric Clamp Meter Resistance 20M ohms with basic accuracy ±(1.0%+4d)Continuity buzzer sound at 300 ohmsDiode test current 0.3mA; Open circuit voltage 1.5VAccessories: test leads, carrying case, 2(AAA) 1.5V batteriesSize:8-1/16"L x 2-3/4"W x 1-1/2"HSlimline Electric Clamp Meter Weight: 7oz.2000 LCD display countsDecimal Point ReadingsDisplay with backlightData holdMax holdAuto power offLow battery indication