Current
See Also: Direct Current, Alternating Current, Resistivity, Flow, Inductance
-
product
General ELCB Testers
TEL1-x Series
Standard Electric Works Co., Ltd
The TEL1 is the Basic Test Equipment an Electrician cannot do without. TEL1 is a Dual Function Test Instrument utilized to Verify Electrical Wiring Connections and the Functioning of Earth Leakage / Residual Current Detectors devices by forcing the ELCB/RCD to trip.
-
product
Mobil Cable Test and Fault Location System
SWG-12 (SWG-32)
• testing cable insulation with DC (rectified) voltage up to 32 kV;• conditioning faults by burning faulty cable insulation with current up to 100 mA;• pre-locating cable faults with the reflectometer RIF-9 based on the pulse reflection method (TDR), voltage wave oscillation method (DECAY), impulse current envelope (ICE) method and arc reflection method (ARC / ARC multi-shot);• pinpointing cable faults with the acoustic method with up to 2000 J surge wave generator and a suitable signal receiver.
-
product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Lead Free Probe
LFRE-1L18-6
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Godzilla High Current Probes, 150 Amp
HC500
Current Rating (Amps): 150Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 260Full Travel (mm): 6.60Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,215Overall Length (mm): 81.66
-
product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
MAGNESIUM ANODE SIMULATOR
CS-1
The CS-1 portable Magnesium Anode Simulator is an ideal DC current source that will allow the user to see what the addition of a magnesium anode on their system will do to Pipe to Soil measurements and other C.P. tests.
-
product
Biosensor isoPod with USB
EPU352
A compact signal conditioner for monitoring low current, two-electrode (anode and cathode) amperometric sensors. By setting the polarization voltage to zero it can also be used as a zero resistance ammeter (ZRA).Electrical isolation ensures that readings are not influenced by nearby current sources such as conductivity, or voltammetric electrodes.
-
product
Free Room Temperature Bore Systems
The cryomagnetic system contains the cryogen free room temperature bore superconducting magnet, cryostat, cryocooler and compressor, temperature monitor unit (nominally Lakeshore) and HTS current leads. The cooling for the magnet and cryostat housing is provided by a standard cryocooler with a base temperature of 4K. The magnet is designed to operate safely at the guaranteed field without quenching.
-
product
Multifunctional testers
MI 3152 EurotestXC
MI 3152 EurotestXC is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN, TT and IT earthing systems are managed by a completely new user interface based on large colour touch screen display. A wide range of functions is included: from on-line voltage monitoring, phase sequence testing, varistor testing, earth resistance measurement, illuminance measurement and TRMS current measurement up to RCD tests, line and loop impedance tests, specific earth resistance measurements as well as ISFL measurements and the IMD tests.
-
product
Standard 2.90 (82.20) - 5.40 (153.00) Switch Probe
TSP157-H200-1
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 157Test Center (mm): 3.99Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 984Overall Length (mm): 25.00Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Regenerative AC load function
61800 Series Optional Function
The regenerative AC load function consists of various modes such as CC Rectified mode, CP Rectified mode, CR mode, CC Phase lead/lag mode and CP Phase lead/ lag mode. The Rectified Mode is capable of simulating non-linear rectified loads with characteristics similar to Chroma 63800 series AC load where the voltage and current operate at the 1st and 3rd quadrant. The Rectified Mode supports both CC and CP functions with current, power and CF as parameter settings.
-
product
Digital Multimeters
Multi-Display : Primary 80000, Secondary 80000, Bargraph 23 SegmentsBasic DC Accuracy : 0.05% mV Impedence : > 1000M OhmMore than 50 Measuring FunctionsFrequency Measurement : 0.5Hz to 8.0000MHz 16 Frequency Points, 1% to 99% Duty. Selectable Square Wave OutputAnalyzing Component of Current or Voltage SignalResistance : 0.1Ω to 80MΩ, 10MΩ to 8000MΩCapacitance : 1nF to 100µFTemperature : -50°C to 1372°C, -58°F to 2502°F dBm 20 Types of Reference ImpedenceAuto Data Hold / Peak HoldRelative Measurement36 Hours Dynamic Recording : MAX / MIN / AVG/ MAX-MINCommunication : Isolated Optical RS-232Timer for MeasurementBacklight DisplayAuto Power Off
-
product
Elevated 2.65 (75.00) - 6.50 (184.00) High Performance Lead Free Probe
LFRE-25T79-6.5
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
5KV Digital Insulation Tester
*Display : 75 X 35 min Backlit LCD with Annunciator*Max. Reading : 1999 Counts *Over the limited range indicator : LCD show "1'*Power supply : Six AA batteries to supply the power, OR 2300, 50Hz AC*Lou voltage indicator :The symbol lft appea.*Power consumption : Static Short circuit current : >2mA (250V-1000V), >1mA (2500V)*Work condition : Temperature 0°C - 40°C, relative humidity: 30%-85% RIO*Storage condition : -10°C - 40°C, relative humidity Dimmenslon : 95x148x85mm*Weight : Approx. 850g (induding battenes)*Accessories : Manuai, one pair of test lines, one pair of crocodile clips. six battenes, Mains Adaptor
-
product
High Performance High Power DC Electronic Load
IT8900A/E Series
IT8900A/E series high performance high power DC electronic load provides three voltage ranges 150V/600V/1200V, stand-alone power from 2kW to 54kW. IT8900A/E series, with ultra-wide voltage and current range, controlled by an independent master unit.
-
product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-614D-015
The 40-614D-015 (PXI) and 42-614D-015 (PXIe) 1-bank, 128-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Standard 1.10 (31.00) - 2.50 (71.00) General Purpose Probe
HPA-1H-1
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 655Overall Length (mm): 16.64
-
product
Standard 1.08 (31.00) - 3.50 (99.00) General Purpose Probe
EPA-2T
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
product
PXI Solid State 8x2 Matrix, 30 Amp
40-555A-011
The 40-555A-011 is a high current 8x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
Artificial Power Network
KH3765
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3765 artificial power supply network is equipped with the receiver produced by our company to conduct large current conduction interference test. The frequency range of this product is 150KHz-30MHz , the current is 50A , and the AC frequency can reach 0-400Hz . It is widely used and convenient to switch. Compared with similar products on the market, it greatly reduces the operation steps and buys valuable time for your rectification work. This product also provides a standard10AThe interface makes your test more convenient. Meet the requirements of GB-6113 for power supply network.
-
product
HV Breakout Modules
The HV Breakout Modules (BM) are specifically designed for safely measuring directly from HV voltage power cables. Currents and voltages are measured directly and the raw data is acquired at up to 2 MHz per channel. With the Vector eMobilityAnalyzer software, which is optimally paired to the CSM HV Breakout Modules, real time power analysis is also possible.
-
product
DC Lab Power Supplies
TD3202M
- Fully Metallic Construction to Stop Radiated EMI- Compact & Rugged Design- DC Output ON/OFF on each Main Output- Voltage & Current Output Preset Facility for Safety- Constant Voltage / Constant Current Mode- 3 Digit DPM V and A- High Stability & Close Regulation ±0.01% +3mV- Low Ripple <1mV rms- Overload Protection- Convection Cooled – No Fans- Meets International Safety Standards
-
product
Towing Dynamometer
RS-25K
RS-25K Towing Dynamometer is designed for testing today’s full-sized SUVs and light trucks. The RS-25K is built with a heavy-duty steel frame, an aerodynamic body and rides on an independent, air ride suspension using two eddy current absorbers with special high temperature coils to absorb energy. The RS-25K is powered by an industrial generator so there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
product
Meter Test Equipment
Signals & Systems India Private Limited
Our meter test equipment is a user-friendly and innovative device for energy meter calibration, built on the current technologies – Bluetooth & Android. The metrology sub-unit measures and communicates the parameters to an Android Tab via Bluetooth. All user interfaces – textual, graphical, and data entry are made available on the Android application, with innovative features. Being a portable device measuring the voltages and currents from the metering panel, the product ensures the safety of the test personnel by making use of wireless communication between the equipment – which is connected to the High Voltage- and the user interface – Tab.
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 43
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
product
Ultra High 4.09 (116.00) - 10.00 (283.00) General Purpose Probe
EPA-2B40-2
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1H-6
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Rogowski Coil Current ProbesTOP
*Switching current waveform and pulse response characteristics of power devices*Current measurements of inverter system*AC current measurements (at large DC offset)*Impulse high current measurements*Bus Bar high current measurements
-
product
Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
Panasonic Industrial Devices Sales Company of America
Panasonic’s Hybrid Capacitors combine the benefits of Aluminum Electrolytic and Specialty Polymer Capacitors resulting in a Capacitor featuring high endurance, low-ESR, high tolerance for ripple current, inrush currents and elevated temperature. Hybrid Capacitors are known for their stable electric characteristics at high frequencies while maximizing reliability. These Hybrid Capacitors are compact, allowing significant board space savings and vibration-proof parts are also available.
-
product
Standard 0.70 (2.00) - 1.70 (4.80) General Purpose Probe
P2262AG-1C1S
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 30Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 90Full Travel (mm): 2.29Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 710Overall Length (mm): 18.03
