Showing recent results 1 - 15 of 85 products found.
-
EEWeb
Crosstalk is unwanted coupled energy between traces. There are two types: forward and backward. This tool calculates backward crosstalk, which is usually the dominant crosstalk component.
-
EEWeb
Crosstalk is unwanted coupled energy between traces. There are two types: forward and backward. This tool calculates backward crosstalk, which is usually the dominant crosstalk component.
-
PXA-1000 - General Photonics Corp.
The PXA-1000 Distributed Polarization Crosstalk (X-Talk) Analyzer is an enhanced white light interferometer that measures space-resolved stress by analyzing stress-induced polarization cross-coupling along a length of polarization maintaining (PM) fiber. The patented design eliminates strong zero-order interference and reduces the multi-coupling interference common in traditional white light interferometers, both of which can cause “ghost” peaks in the measured signal. The removal of the “ghost” peaks enables the PXA-1000 to unambiguously identify the magnitudes and locations of actual x-talk peaks, resulting in higher measurement sensitivity, higher dynamic range, and higher spatial measurement accuracy.
-
XTALK-32 - Wild River Technology
The is an industry first product consisting of a family of loss and Insertion-Crosstalk Ratio (ICR) designed to challenge 6-32 Gbpsec systems and PAM-4, 56 Gbpsec. ICR is a basic measure of signal versus crosstalk energy (similar to Signal/Noise) and provides 50 (very low XTALK) to 15 (very high XTALK) for both 10 and 28 Gbpsec systems. Crosstalk energy and Victim loss can further be tuned with optional pad kit. Structures can be combined with other platforms or on-board structures using optional low skew <1 psec matched cable kit.
-
LSX 2020 - Sparnex Instruments
Performance. Noise immunity. Crosstalk stability and Remote Powering functionality. Line Simulation up to 3 MHz. 100% freely configurable lines. Based on the Active Analog Concept (AAC). Internal Line Libraries, Noise and Crosstalk generators
-
ATE Service Corp
Place inner layer GND plane all over. Impedance control of signal line and crosstalk prevention, etc. contribute to improvement of characteristics in various ways.
-
10 Channel - Dexter Research Center, Inc.
A ten-channel thin-film thermopile in a TO-8 package. Each active area is 3.16mm x 0.4mm and offers low noise voltage. Internal aperture minimizes channel-to-channel crosstalk while increasing sensitivity.
-
DR34 Compensated - Dexter Research Center, Inc.
A one-channel compensated thin-film thermopile in a TO-5 package. The active area and compensating element area are 3.16mm x 0.4mm each. Internal aperture minimizes channel-to-channel crosstalk and thus increasing sensitivity.
-
TM34 - Dexter Research Center, Inc.
A three-channel thin-film thermopile in a TO-8 package. Each symmetrically positioned active area is 3.16mm x 0.4mm. Offers low noise output and internal aperture minimizing channel-to-channel crosstalk while increasing sensitivity.
-
HITEC Sensor Solutions Inc.
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
ShaH - Del Mar Photonics, Inc.
The family of fast, accurate and reliable wavefront sensors. High quality lenslet arrays optimized for reducing the subapereture crosstalk. An interface to a variety of CCD and CMOS sensors allows a wide range of acquisition bands from UV to near IR.
-
DR46 - Dexter Research Center, Inc.
A two-channel or a one-channel compensated thin-film thermopile in a TO-8 package. Each active area is 4mm x 0.6mm. Offers high output with excellent signal-to-noise ratio. An internal aperture minimizes channel-to-channel crosstalk increasing sensitivity.
-
ET91 - Vonaq Ltd
*Level Meter, for selective and wideband level measurements with auto ranging*Generator, for the generation of measuring voltage for the test of FDM systems*Bridge, for the measurement of input and output parameter*Spectrum Analyser, for the test of output PSD, cross-talk and other interference signals
-
M2C - Lectrosonics, Inc.
The M2C active antenna combiner is designed as an ideal matching component to Lectrosonics digital transmitters. Up to eight transmitters can feed a single antenna to minimize cabling in multi-channel systems. The inputs are isolated to minimize crosstalk and IM (intermodulation) between RF channels.
-
2M Quad - Dexter Research Center, Inc.
A four-channel thin-film thermopile in a TO-8 package. Each active area is 2mm x 2mm. Offers the world's highest 4-channel sensitivity with exceptional signal-to-noise performance in a TO-8 package. Internal aperture minimizes channel-to-channel crosstalk while increasing sensitivity.
