-
product
8-Channel VME Time-to-Digital Converter
V680
The V680 is an 8-channel time-to-digital converter used to record the time of occurrence of eight independent electrical pulse inputs, each measured relative to a single, common reference input. Each input channel can time its event "hit" with 48.82-picosecond resolution and 48-bit dynamic range.
-
product
Platform
ATX7006A
The ATX7006A is a fully integrated solution for testing ADCs, DACs and other Analog functions. It combines very high accuracy, low noise and fast sampling with an exceptional ease of use. Traditionally data converters are tested using a whole stack of bench instruments, filters, switch matrices and user made software. Many engineering hours are needed to get reliable results. The ATX7006A is a single instrument for all your data converter testing and test methods.
-
product
Universal Converter
C8000
Multi channel converter for all optek photometric and conductivity sensors and electrochemical pH electrodes. Flexible configuration of sensors, measuring ranges, units and product specific setups make the C8000 converter series a powerful device in process monitoring in both conventional and single-use systems.
-
product
64 Channel Multihit TDC
V1190B-2eSST
The V1190B-2eSST is a 64 channel Multihit TDC, housed in a 1-unit wide VME 6U module. The unit features High Performance Time to Digital Converter chips developed by CERN. LSB can be set at 100 ps (19 bit resolution, 52 µs FSR), 200 ps (19 bit, 104 µs FSR) or 800 ps (17 bit, 104 µs FSR).
-
product
Synchro to Digital-Resolver to Digital Converters
MSI MRI MX
Computer Conversions Corporation
Computer Conversions MX Series are low cost multiplexed synchro or resolver to digital converter sets designed for Military or Industrial diagnostic and control applicatioms requiring 3-128 axis per control.
-
product
Digital Down-Conversion Firmware
FW2DDC
FW2DDC equips ADQ7WB and ADQ7DC with real-time functions commonly used in radio frequency (RF) receivers. It also contains the proprietary ADX technology which corrects mismatch errors in time-interleaved analog-to-digital converters (TI-ADCs) and thereby ensure industry-leading spurious-free dynamic range (SFDR). The digital signal processing also helps reduce the data rate to a manageable level in order to simplify data post-processing and storage.
-
product
Data Acquisition Systems
Encore Electronics manufactures a wide range of analog signal conditioning equipment, including strain gage and pressure amplifiers, frequency-to-voltage converters, thermocouple isolation amplifiers and anti-aliasing filters.
-
product
Testing of Current Measuring Transformers
All components from this category can be integrated into an existing current transformer test system. When selecting CT test components, both the type of converter to be tested and the required current are important.
-
product
Synchro/Resolver to Digital Converters
Resolvers and synchros are transducers that convert the angular position and/or velocity of a rotating shaft to an electrical signal. Both deliver signals proportional to the sine and/or cosine of the shaft angle. A resolver-to-digital or synchro-to-digital converter converts these signals to a digital output corresponding to the shaft angle and/or velocity. ADI’s family of RDCs and SDCs offer solutions for these applications.
-
product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
PXIe-4310, 16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module
784813-01
16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module—The PXIe-4310 is a channel-to-channel isolated, filtered analog input module for higher voltage measurements. The module offers the ability to select an analog filter per channel to provide extra filtering performance. You also can operate up to four different input ranges per terminal block and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI-DAQmx driver simplifies hardware configuration and measurement.
-
product
Level Control Loop Trainer Model
ULP-24P & ULP-24C
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Level Control Setup comprises of acrylic measuring tank fitted with Level transmitter, control valve, I to P converter, source tank with water pump and necessary flexible piping for water circulation. The system is mounted on a table top powder coated metal frame. Level transmitter is of capacitance or DPT type sensor. The electronic panel comprises of ADC and DAC card with RS-232 interfaces.
-
product
16-Channel VME Multi-Range Digitizer
V490
The V490 includes 16 independent acquisition channels, each with a programmable-gain differential amplifier, analog anti-aliasing filter, 16-bit analog-to-digital converter, and digital post-processing. With a dedicated A/D converter per channel, the V490 provides true simultaneous sampling, which can be extended across multiple V490s or triggered from an external TTL signal.
-
product
Signal Converters & Load Cell Signal Converter
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
product
AC Power Supplies & Frequency Converters
Behlman manufactures a broad line of AC Power supplies and Frequency converters with available power from 1,000 VA to 120,000 VA in both single-phase and three-phase output. Available with variable or fixed voltage and frequency output, manual or programmable control, with a variety of interfaces, unique protection circuitry and the ability to modify units for your application.
-
product
6U cPCI D/S & Multifunction I/O
78CS1
The 78CS1 is a cPCI Synchro/Resolver Measurement and Simulation Board that provides 8 S/D and 6 D/S Converter Channels, with accurate velocity outputs, that can be used in single-speed or two-speed modes. It provides wrap-around self-test, PXI compatibility, optional Programmable Reference Supply, and is available for Military or Commercial applications.
-
product
Analog Output Cards
PCIe-DA16-6
The PCIe-DA16-6 series are x1 10.5” cards that can be installed in long PCIe slots. They contain six, four, or two digital-to-analog converters (DACs) and 16 bits of digital I/O.
-
product
2-Quadrant Source/Measure Unit for Functional Test, 20 V, 1 A or 6 V, 3 A, 20 W
N6782A
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
product
Solar ATE
MS 1534
The Inverterless ATE is an automatic test equipment which is used to test the all functional and various test conditions of Inverterless Solar Unit. This ATE shall be a GO/NOGO Tester for Inverterless Solar Unit. All production units can be tested with this ATE for functional testing and clearance. This ATE reduces the man effort for quality checks and detects the failure units. The Inverterless ATE can check the UUT with minimum user interactions. It shall test and generate test report in PDF f...show more -
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
Half, Full Bridge & Three-Phase Drivers For Automotive
Renesas' AEC-Q100 qualified 100V half-bridge drivers safely drive MOSFETs for bidirectional controllers in 12V to 48V automotive hybrid powertrains. The advanced ISL784x4 MOSFET driver family enables high current DC/DC conversion with adjustable dead time and maximum efficiency. The ISL784x4 drivers are also well suited for 12V to 24V bidirectional DC/DC converters, as well as other high current buck or boost applications.
-
product
- Single Mode to Multimode Converter
Model 279
FEATURES: DC to 2.5 MBPS; Full duplex; 850nm to 1300nm; In line mounting; Small size; Data LED's; Line Loss switch; Single-mode distance to 20 Kilometers. The Model 279 provides transparent conversion between fiber optic devices utilizing multi-mode fiber and those with single-mode fiber.
-
product
45~1050MHz FTTH CATV O/E Convertor
H9008B
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai H9008B series CATV converter for digital television, fiber to the home. This machine adopts the high sensitivity optical receiving tube, without power supply, no power consumption. When the input optical power output level Pin=-1dBm, Vo=6 8dB V, can be economically and flexibly apply the integration of three networks, fiber to the home network application.
-
product
Digital Three-Phase Uni & Directional Converters
Start Power equipments series SCxQML230 are totally controlled three-phase digital converters operating up to 500 Vac voltage, 360A current, frequency between 45 and 62Hz; they are suitable for speed and motor torque regulation. Sizes with current up to 9000 A are available in different mechanical dimensions.
-
product
SparkFun I2S Audio Breakout
MAX98357A
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both.
-
product
16 channel 16 bit Digital to Analog Module
CPCI-DA16-2
The CPCI-DA16 is a slave Digital to Analog board thatis managed by the host processor on the CPCI bus.The card contains a state machine that performs mostof the work of outputting data, in order to minimize theimpact to the HOST system.
-
product
Optical Path Converter
LS512A/LS512B
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is t...show more -
product
FTTH Optical Node
SR100SC3
Hangzhou Softel Optic Co., Ltd.
SR100SC3 series CATV converter for digital television, fiber to the home. This machine adopts the high sensitivity optical receiving tube, without power supply, no power consumption. When the input optical power output level Pin=-1dBm, Vo=6 8dB V, can be economically and flexibly apply the integration of three networks, fiber to the home network application. SR100 appearance of enamel, there are two kinds of optical mode selection:
-
product
DC-DC Converters
Our proven ability to blend circuit topologies and high-performance components with contemporary construction techniques has led to our premier position in the industry as the largest supplier of DC-DC converters. From standard models to modified products and complete custom designs, Murata''s DC/DC converters can meet the needs for miniaturization, low profile, high efficiency, power-saving, low noise designs for use in industrial and electronic equipment, telecom, medical, automotive, lighting, and more.
-
product
Gate Drivers
A necessary companion for discrete power MOSFETs and IGBTs as well as digital – microcontrollers, DSPs and FPGs – or analog controllers in any switched-mode power converter, STDRIVE gate drivers generate the necessary voltage and current level required to accurately and efficiently activate the power stage in industrial, consumer, computer and automotive applications.
