-
product
Digital Attenuator
Chengdu KeyLink Microwave Technology Co., Ltd.
The products can be used in microwave electronic components. Its attenuation values are determined by the input TTL/LVTTL control signal. So that the link can be achieved the desired gain or loss value.KeyLink's digital attenuators can be categorized as follows.
-
product
High Temp Lab Dyeing Machine
TESTEX Testing Equipment Systems Ltd.
High Temp Lab Dyeing Machine, suitable in various galley proofs dyeing and the laundering firm test. The highest operating temperature reaches 140 °C. Equipped with programmable micro computer control system, repeatable working condition. May simulate the actual operating conditions.
-
product
Signaling Control and Monitor Equipment
MS 1303
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
product
Luminance Meters
Konica Minolta Sensing Americas, Inc
Luminance meters are single element detectors that measure photometric brightness. The Konica Minolta luminance meter measures the amount of emitted or reflected light from a surface. These instruments display luminance in either cd/m2 or foot-lambert (ft-L) and they are lightweight, compact and portable. They can be connected to a PC which can store the measurement data and control the device. The LS-160 has a single lens reflex optical system to precisely measure very small (0.4mm) diameters at very short distances, making it extremely easy to use.
-
product
Clamp type AC Current Sensor／with DC Voltage Output
ACT-50H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 1A～50A*DC 5V full scale output
-
product
Mass Flow Controller
SEC-E Series
This general purpose mass flow controller has a reliable thermal sensor and solenoid valve, allowing you to achieve high-level control of gas flow. A versatile component, the mass flow controller sec-e series can be used in a wide range of industries.Gas flow through the mass flow controller can be controlled over a range of flows: from 10 SCCM to 200 SLM.
-
product
EZ-Glider Articulated Torque Arms
The EZ-Glider torque arms are designed to improve production and quality control during the assembly process. With the ability to bend like an elbow, the torque arm provides agility to position the tool in a variety of positions for different applications. Arm can be set at an inclination of 0º, 22.5º & 45º. The effortless handling of the torque arm provides comfortable tool operation and increased production.
-
product
HFC 4 Ways Return Path Optical Receiver
HR2040A, HR2040B
Hangzhou Huatai Optic Tech. Co., Ltd.
HR2040 series HFC four ways return path receiver can convert upstream optical signal to RF signal at the head-end and remote control center. Four independent receivers integrated into a 1RU 19” casing to supply service for HFC network terminal. Receiver's low noise design, -22dBm receive sensitivity can provide service to farther place. There are two versions of this receiver. HR2040A with LCD on the front panel, HR2040B without LCD. All receivers are temperature tolerance type can be installed ...show more -
product
Power Monitoring Dynamometer
90085
Model 90085 is designed to measure machine tool output. This model acquires the necessary torque and speed data needed to calculate the horsepower of the machine tool under test conditions. It is a portable, self-contained data acquisition and monitoring system consisting of three major components: a pneumatic brake assembly, a torque and speed transducer, and the control and display module.
-
product
Solar Array Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-spec...show more -
product
Magnetic Permeability Meter Ferromaster
Instrument for easy measurement of the relative magnetic permeability µr of feebly magnetic materials and workpieces with a permeability between 1.001 and 1.999. The permeability is measured by touching the workpiece with the probe tip and reading the result from the display. Typical applications are: non-destructive testing of materials, e. g. quality control of stainless steel, material selection for electron-/ion-beam equipment, detection of material defects induced by mechanical or thermal stress.
-
product
Modbus Register Converter - Serial To Modbus RTU Interface
Translates Modbus registers and variable types from an older Modbus devices to a new Modbus device. The Model 2390 allows upgrading Modbus RTU devices without changing the system software. The 2390 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands strings when controlling Modbus RTU devices.
-
product
6000 Series Analog I/O Modules
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the m...show more -
product
PDS Multibeam Survey and Processing/Charting
Teledyne PDS for Multibeam Surveys provides the functionality for survey planning, data acquisition, data processing, editing, volume calculations and chart production. This turnkey solution offers the surveyor and helmsman a strong tool to carry out the multibeam survey efficiently. Progress is shown real time in top, profile, and 3D views using a color-coded digital terrain model (DTM). Various filter settings can be applied to the multibeam data online, thus providing real-time data processing. Quality control displays reassure the operators that the data is of the desired quality.
-
product
Transformer Turns Ratio Testers
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transfor...show more -
product
MIMIC NetFlow Simulator
MIMIC NetFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
product
Transmitter Control Subsystem (TCS)
Loran C Accufix 7500
USCG Loran Transmitter Control and Display stations modernized and upgraded to state-of-the-art processor controlled technology. Fully redundant system with comprehensive built-in performance monitoring. Automatic switchover upon detection of error, high single point failure tolerance. Long distance communications link supports remote station operation on a continuous basis. Built-in fault detection and monitoring enables dynamic re-allocation of failed subsystem modules, and fault isolation to major replacement assemblies.
-
-
product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
779516-01
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
-
product
Elevator Drives
User friendliness is the emphasis of our drives. The keypad interface and programming are dedicated to elevator and escalator applications. The performance features are well-suited for both Induction and Permanent Magnet motors with the latest control functions.
-
product
NI-9881, 1-Port C Series CANopen Interface Module
781673-02
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
product
IO-Link Sensors for Motion Control
Encoder for precise position determination and linear measurement, Defined pulse sequence for the reliable detection of rotational speeds, Inclination sensors for precise measurement of angles of inclination on X and Y axes, High measurement accuracy across the total angular range in two axes, High protection rating for the requirements of harsh industrial environments
-
product
PCI Analog IO Board
MS 1803
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
product
Precision Current Sources
HighFinesse Precision Current Sources have been developed for experiments and quantum technologies in the areas of cold-atom and solid state physics. The linearly regulated BCS (Bipolar Current Source) and UCS (Unipolar Current Source) series deliver highly stable, low noise source currents for high precision magnetic field control. The current output is floating or is on a used defined potential. Ultrafast response to control signals and trigger functions, clear grounding, connection and signal isolation schemes make the integration of the current sources into complex experimental systems easy.
-
product
Water Activity Measurement, Moisture Meter, Measurement and Monitoring of AW Value
The measurement of water activity or equilibrium relative humidity (ERH) is a key parameter in the quality control of moisture sensitive products or materials.
-
product
RF Thermistor Power Meter
1830A
Thermistor based RF power sensors are universally recognized as the most accurate means to measure and transfer RF power. Compatible with thermistor power sensors from: Agilent (HP), TEGAM, Weinschel, Hughes, General Microwave, Millitech. Supports 100 and 200 thermistors. Integrates bridge balancer and power meter into one package. Four digit calibration factor resolution. Full remote programmability. Heater control for ovenized sensors. LXI Compliant.
-
product
Signal Generator, 20MHz, 1 Channel, Arb.
33511B
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
product
Hydrogen Frequency & Time Standard
CH1-1033
The hydrogen frequency and time standard Ch1-1033 is designed for precision storage and reproduction of the size of frequency and time units as part of measures and reference complexes. Main areas of application: – public service of time and frequency; – ground control complexes of radio navigation systems; – radio interferometry with extra long base.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm
50-293-024
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
