Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected thr...show more -
product
500 Pin SEARAY Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
PXI/PXIe Power Relay Module, 32xSPDT, 5 Amp, 50-Pin SGMC Connectors
40-158-001
The 40/42-158-001 is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
product
Gaussmeter
DX-101
DX-101 Gaussmeter is based on the Hall effect magnetic field strength of the latest developments in instrumentation, the design of desktop-type Gauss meter. Maximum range 330.0mT and 3000mT two tranches, the minimum basic error of 1.0%. Test probe connectors is imported, stable and reliable connection.
-
product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Male SCSI Connectors
510150125
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Male SCSI Connectors
-
product
Latching (Non-Terminated), SP3T, SP4T, or SP6T Multi-Throw Switch, 50Ω Impedance, SMA Connectors
Part No.s CCR-39S/CR-39S SP3T/ SP4T/ SP6T
Latching, SP3T, SP4T, or SP6T Multi-Throw switch, 50Ω impedance Available in Commercial and Elite models, with SMA connectorsDC-18GHz (commercial) DC-22GHz (Elite)
-
product
PXI 16x4 RF Matrix 300MHz 50 SMB
40-727-001
RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors.
-
product
Rectangular Connectors
Smiths Interconnect offer a broad range of modular and rectangular connectors. Our modular solutions allow the user to customize, configure and combine signal, Power, Filter High Speed Data (coax, twinax, triax, quadrax, fiber optic) contacts into a single connector.
-
product
NI-9973, 6-Pin, Male COMBICON to 6-Pin, Female Spring Terminal Block Plug
196738-01
6-Pin, Male COMBICON to 6-Pin, Female Spring Terminal Block Plug - The NI-9973 features four spring terminal plugs for any 6-position spring terminal C Series module. It provides direct connectivity to the module. All C Series modules ship with the required connectors, so you can … purchase the NI-9973 to reduce wiring on multiple devices or use for spare replacements.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 18 GHz, 50 Ω, SMA, External Termination, Failsafe
42-781A-122
The 40-781A-122 (PXI) and 42-781A-122 (PXIe) are dual SPDT failsafe 18 GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
7/16 DIN Connectors
Pasternack 7-16 DIN connector category includes many part numbers, most are RoHS and REACH compliant. 7-16 DIN connector series in this category will terminate to coax or terminal. Our 7-16 DIN connectors are built to precise industry specifications. 7/16 DIN connector items are available in male or female gender with 50 Ohm impedance. 7-16 DIN connectors are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. These DIN 7-16 conn...show more -
product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB With Loop-thru
40-727A-101-L
The 40-727A-101-L (PXI) and 42-727A-101-L (PXIe) are 16x4 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
-
product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix topology With Column Protection Resistors
782385-12
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
LXI Microwave Multiplexer, SP6T, 13-Bank, 18GHz, 50Ω, SMA
60-800-113
Our 60-800-113 is a 13 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI 16x2 RF Matrix 300MHz 50 SMB
40-728-001
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
product
18" Ribbon Cable
CONM50-D25-1
An 18" ribbon cable transitions from individual IP Module ribbon connectors on the ISA (PC/AT) carrier board to a 25 pin female D-sub connector mounted on a PC expansion card end-panel.
-
product
PXI/PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, External Termination, Failsafe, Remote Mount
40-781A-321-E
The 40-781A-321-E (PXI) and 42-781A-321-E (PXIe) are single failsafe SPDT 26.5 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Cable Assy 25-Pin D-Type F/F 1m
40-970-025-1m-FF
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 12.4 GHz, 50 Ω, N-Type, Failsafe
42-780B-512
The 40-780B-512 (PXI) and 42-780B-512 (PXIe) are dual failsafe SPDT 12.4 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
LXI Microwave Multiplexer, SP6T, 7-Bank, 26.5GHz, 50Ω, SMA
60-800-307
Our 60-800-307 is a 7 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Hard Metric Eurocard Plugbord
8020
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad-Per-Hole and peripheral bus both sides. Pad and bus surfaces not solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
product
PXI 8x2 RF Matrix 1.5GHz 50 SMB
40-750-511
The 40-750-511 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMB coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
product
LXI Microwave Multiplexer, SP4T, 3-Bank, 18GHz, 50Ω, SMA
60-803-103
Our 60-803-103 is a 3 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
3U CompactPCI® 4 RJ45 Port Gigabit Ethernet Card
MIC-3958
Advantech MIC-3958 Series, a 3U height 4HP CompactPCI® peripheral card, using Intel® i210 Ethernet controller, to support up to four RJ45 Gigabit lan connectors, two switchable with rear transition module; MIC-3958A provides four RJ45 lan ports on front panel, MIC-3958R provides two RJ45 lan ports on rear IO panel. Its ideal power solution make it perfect for all fanless system applications.
-
product
PC/104 OneBank Carrier
EMC²-SoM
Sundance Multiprocessor Technology Ltd.
The EMC²-SoM is a PCIe/104 OneBank™ Carrier for a Trenz compatible FPGA and SoC Module and has expansion for a VITA57.1 FMC™ LPC I/O board. It also has I/O pins, using a 100-way Samtec RazorBeam connectors system, the “Sundance Expansion Interface Connector” (SEIC) can be customize for individual applications and bespoke connectors.
-
product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 2m, 250 Port
A500RMR-05F050D4B200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 1-Bank 6GHz SMA
60-801-001
The 60-801-001 is a 6-channel, 1-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Power Supplies
CUL-850B
The CUL-series is a semi-modular power supply that lets you select the cables you need while powering your gaming system with a 140mm Blue LED cooling fan and 6 pin PCI-E ready. **850W & 950W is offering 140mm Blue LED cooling fan & Dual 6+2 PCI-E ready. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power & 4+4 pin CPU connector are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
product
SIMRC - 16 x Uncommitted Reed Relay, SPST Screened
1010-R-16-1RF-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
