Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
200-Pin LFH Connector Block, Male
92-965-200-M
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure that appropriate electrical safety precautions are observed.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 50 GHz, 50 Ω, SMA-2.4, Failsafe, Remote Mount
40-782B-551-E
The 40-782B-551-E (PXI) and 42-782B-551-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
product
Power Supplies
CT-450
The CT series has a dual smart fan system that provides the fastest cooling system while maintaining a low noise level. The fans are installed in the front and rear of the power supply for maximum cooling efficiency. The CT series have all the necessary connectors to power all your devices and components. And it is PCI-E ready.
-
product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω MS-M Multiway
42-729A-002
The 40-729A-001 (PXI) and 42-729A-001 (PXIe) are 8x4 50 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
Omicron Fiber Optic Connector
Teledyne Impulse-PDM’s Omicron 5030/5070 optical connectors utilize proven small form factor ferrule technology and are available for multi-mode or single-mode operation.The connectors are offered, as standard, in stainless steel to BSEN10088-3 Grade 1.4404 (316L), which is electro-polished to remove surface contamination, thus improving resistance to corrosion. Connector bodies can also be manufactured in other materials, either to address specific anti-corrosion requirements, or to increase depth rating. Engaging nuts are normally manufactured in naval brass to UNS C46400.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 7-Bank 6GHz SMA
60-801-007
The 60-801-007 is a 6-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
68-Pin SCSI Micro-D Male Connector Block
40-965-068-M
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
AS5653 Compliant Small Form Pluggable (SFP) Transceiver
XCVR-AS5653
Avionics Interface Technologies
AS5653 SFP transceiver that can be inserted into any standard SFP slot - 1.0625 GBPS communication signals interface using TNC connectors - Bulkhead mountable female TNC connector at the end of a 1 meter length of RG179B/U - 100 feet of RG179 operates to better than 10E‐13 Bit Error Rate - Available for 75 Ohm single ended copper or 150 Ohm Differential
-
product
16 Channel Low Threshold Discriminator
V814
The Mod. V814 is a 1-unit wide VME module housing a 16 channel low threshold discriminator. The module accepts 16 negative (positive on request) inputs and produces 16 differential ECL outputs with a fan-out of two on four front panel flat cable connectors.
-
product
Power Supplies
RM - SERIES
With dual PCI-E connectors, the RM Series carries all its essentials to power your system. Enjoy the graphic rendered programs and games without the threat of overheating. Its dark aluminum chassis not only looks good, but dramatically relieves heat built-up. The 120mm cooling fan enhances the already efficient heat dissipation rate and helps balance the cooling system with noise level. The RM Series is great for high end users to everyday casual users. Whatever your system needs, the RM Series can deliver.
-
product
LXI Trigger Bus Cable
ProDAQ 8036
The ProDAQ 8036 LXI trigger bus cable connects the ProDAQ 6100 LXI function card carrier or the 3030 PCI Express VXIbus slot-0 interface to any device equipped with LXI triggers. The robust, shielded cable and the die-cast connectors ensure a stable connection and prevent accidental disconnects.
-
product
RF Connectors
BNC Connectors
BNC connector types feature a bayonet style coupling mechanism that allows for quick connect and disconnect with positive locking. Mating is achieved with just a quarter-turn of the coupling nut. With a classic, dependable design, BNC RF connectors are suited to accommodate a large variety of RG and industry-standard coaxial cables, in a variety of termination styles.
-
product
Controller
Model 4110/4100
The Model 4110 Controller retrieves electricalsignals from the Model 3000 Transducer, interprets the information, and relaysthe data to the local data logger. The standard controller features threeAmphenol connectors that communicate with the transducer, receive supply+12V power and SDI communications to the data logger and communicate via RS-232Serial signal to a data logger. * Connections to DCP and Transducer * Easy to install and maintain * Compatible with RS232 outputAlso available from the factory is the same Model 4110Controller with flying leads in place of the amphenol connectors standardbetween the Transducer and DSP.
-
product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω SMB With Loop-thru
42-729A-001-L
The 40-729A-001-L (PXI) and 42-729A-001-L (PXIe) are 8x4 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
Digital Inspector
DI-1000MPO+
The DI-1000MPO+ incorporates the same features and uses the same single fiber tips and accessories as the popular DI-1000, but adds additional X- and Y-direction scanning knobs. This allows the user to manually scan in both the X and Y directions with one hand, providing unprecedented control and increasing the efficiency of inspecting the endfaces of MTP®/MPO connectors.
-
product
Retractable Cable With Magnet Adsorption
3701
Peaceful Thriving Enterprise Co Ltd
*2 x 6m retractable test leads.*Used as an extension cord for cars, trailers, boats and more.*Optional accessory included alligator clips, test probes and banana plugs.*The tester can be used with any multi meter or device equipped with banana jack connectors.*Embedd A Magnet on the back to fix on suitable metal sheet of cars easily.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber
40-850A-514-M50-HI
The 40/42-850A-514-M50-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
9 Pin D-type Connectors & Cables
These standard voltage and high voltage 9 Pin D-type connectors are used for both PXI & LXI switching and simulation products for low density applications.
-
product
25 Pin 1.27mm Pitch Micro-D Connectors
The connectors below are suitable for high-density applications including Pickering’s LXI DIO/Trigger port.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, LC Connectors
42-850A-414-M62.5
The 40/42-850A-414-M62.5 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
68-Pin SCSI Micro-D M to 2x34 2m
40-971-068-2m-MF
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 2x34-Pin Twisted Pair cable with PVC insulation, terminating with 2x34-Pin polarised IDC connectors. Strain relief is provided via a metal spring latch on the 68-Pin connector.
-
product
100 Pin Breakout Interface
VSI-Breakout-100
The VSI-Breakout-100 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors, With Interlock
42-153-002-HI
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
PXI Dual SP6T MUX 26.5GHz 50Ω SMA
40-784-032
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Picolo Alert PCIe
4x BNC connectors on the bracket, expandable to 16 with three [1203] VEB modules (sold separately)PCIe x1 busSixteen shared video decoders, 100/120 images per second (200/240 fields per second)Real-time acquisition from 4 cameras, fast switching between up to 16 camerasIndependently-programmable frame rate and acquisition parameters for each video input
-
product
Rear-Panel I/O Transition Module
CP3-GESW8-TM8
CP3-GESW8-TM8 is a rear-panel I/O transition module providing flexible access to CP3-GESW8 or NETernity™ CP3-GESW8N rear-panel I/O. Up to eight Gigabit Ethernet ports of the switch are accessible from the transition module's stacked RJ-45 connectors. Each Ethernet port is routed as four 100 Ohm differential pairs.
-
product
MM Fiber Test
KI-TK032
850/1300 nm source & power meter, inspection microscope, cleaning materials. Interchangeable SC & LC connectors
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass, Multi-Mode, 62.5/125 Fiber
40-860A-212-M-HI
The 40/42-860A-212-M-HI is a PXI/PXIe single insert/bypass switch with SC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
200 Pin LFH Connectors for Pickering
The connectors below are suitable to use with Pickering cards and modules that utilize a 200-pin LFH connector.
-
product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
