Showing results: 2701 - 2715 of 2822 items found.
-
Efield AB
Efield® offers a complete and unique integrated modelling and simulation environment for 3D analysis of a wide range of electromagnetic applications such as: Antenna design All kind of antennas including horn, reflector, wire and microstrip antennas as well as broadband antennas and antenna arrays. Antenna integration Radiation pattern of installed antennas on large platforms such as aircraft or ships. Coupling between installed antennas. Microwave design Typical applications includes design of filters, connectors and couplers. EMI/EMC interaction Analysis of a wide range of EMC/EMI problems including shielding and coupling. Scattering & radar cross-section RCS analysis of structures such as aircraft, ships, air-intakes, exhausts, and antennas.
-
AD14-65Mx16AVE -
Ultraview Corporation
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
Meritec
Meritec's 1MM Slot Test Connector was developed to eliminate many of the common problems associated with using a standard connector in a test application. When testing, the PCB is plugged in and out of the connector many times. The wiping action that occurs between the contacts and the board starts to wear down the plating on the contacts and the plastic housing itself.At some point in time the connector becomes a liability and can no longer be considered reliable. The standard connectors being used today for test applications have a life cycle of 250 to 500 (the number of insertion and withdrawals applied to the connector). Meritec's Slot Test Connector has a life cycle greater than 100,000!
-
Analog Devices Inc.
Analog Devices Car Camera Bus (C2B™) is an innovative new camera link technology enabling HD video over Unshielded Twisted Pair (UTP) cables and unshielded connectors. C2B provides an easy upgrade path from SD to HD cameras without the need to change the existing cable and connector infrastructure. C2B enables a camera link with reduced system cost, significant weight savings and increased robustness. The C2B portfolio of transmitter and receiver devices enable seamless camera connectivity in the vehicle. The C2B technology was defined and designed for automotive applications and provides a robust camera link solution for these applications:
-
Dynamic Test Solutions
DTS Package Test (DIB) loadboards are designed to specific devices and configured for both hand test and fully automated handler applications. DTS loadboards incorporate any brand of socket or contactor and can be configured for multi-site testing. Designs incorporate all necessary components, connectors, mechanical hardware and stiffeners to provide a complete plug-n-play solution. DTS has a vast database of tester and handler information which allow designs to be started and completed quickly without burdening the customer to supply excessive information. DTS designers are experienced in all device types, including digital, analog, mixed signal and RF devices.
-
MODEL DPM-2 -
Transducer Techniques, Inc
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
CA9809 -
UC Instruments, Corp.
The UC INSTRUEMNTS CA9809 2.0 ~ 68.0 Gb/s Pulse Pattern Generator pulse pattern generator and error detector is a high performance, flexible and costeffective broad band data rate covered Pulse Pattern Generator that can operate from 2.0 Gb/s to 68 Gb/s. The CA9809 can be used with existing equipment to generate higher rate bit streams for use in telecom applications up to 68 Gb/s. Broadband test systems will benefit from the low power dissipation, precision connectors, and excellent output waveform characteristics. The compact size of the equipment allows the CA9809 to be placed at the measurement plane, reducing or eliminating artifacts related to long cables.
-
SOA -
Amonics Ltd.
Amonics SOA is a polarization maintaining optical amplifier with high fiber-to-fiber gain. It is designed for transmitter applications to increase optical launch power to compensate for the loss of other optical devices. The benchtop version incorporates a user-friendly front panel housing a LCD monitor display, key switch, power control knob and optical connectors. RS232 computer interface is also equipped on the rear panel. 1MHz with 10ns pulse width intensity modulation is available. The OEM module version is an ideal building block for OEM system integration, especially in optical communication network and CATV applications. It requires only a single +5V power supply.
-
UBS2000 -
NG Systems Ltd
One of the main advantages of the Telematrix system is the relative ease in which both large and small matrix systems may be conceived and assembled from a selection of only five basic components. The five main components forming the Telematrix are the Enclosure, the CPU Card, the Input Card, the Output Card and the Input Device (keyboards etc.). Cards simply slide into the enclosure on nylon card guides and secured by two small screws. Keyboards are connected by a flexible 4 core telephone lead and plug into the Telematrix using standard BT plugs (X2110, X2120) or via a standard 4 pair CAT5 cable terminating on RJ45 IDC connectors (X2140).
-
Acces I/O Products, Inc.
A small form factor embedded computer board, typically intended for use in small, space-constrained industrial control or vehicles systems. The standard size of these modules is just 3.550 × 3.775 inches (90 × 96 mm). The name PC/104 comes from the original IBM computer known as the "PC", and the number of pins used to connect the cards together (104). PC/104 boards are typically stacked on top of each other using stackable bus connectors and four mounting holes at the corner of each module. This provides a much more rugged, embedded computer that can be used in harsh environments such as those found in military or industrial applications.
-
85132F -
Keysight Technologies
The Keysight 85132F is a 62.9 cm (24.75 in) long¹ flexible cable set composed of two 3.5 mm female² to 7 mm connectors. Cable frequency range is dc to 18 GHz with a return loss greater than or equal to 17 dB. Insertion loss is 0.25 * sqrt(f) + 0.2, where f is frequency in GHz, for the test port connector and device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability¹ of the Keysight 85132F is less than 0.12 dB and phase is 0.13 * f + 0.5, where f is frequency in GHz.
-
781156-01 -
NI
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
SX set -
Langer EMV-Technik GmbH
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
TYPE HFX-1 -
National RF, Inc
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
ERAVANT
Dielectric resonator oscillators (DRO) are free running oscillators that utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals with excellent frequency stability. In addition, these oscillators are equipped with an internal voltage regulator that further improves the frequency stability by isolating the external bias pushing and modulation. In general, these oscillators are fixed. However, a small mechanical or electrical tuning range can be achieved by use of a self-locking screw or an integrated Varactor diode. The standard offering covers the frequency range of 2 to 40 GHz. While standard models are equipped with female SMA and K connectors at the RF port, other RF interface options are also available.
