Showing results: 256 - 270 of 2822 items found.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a 100-pin Micro-D connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 50-pin D-type connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 9-pin D-type connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 9-pin D-type connector.
-
106PIBM602-0000R -
ELMA Electronic, Inc.
the PIB 6U 2 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
MODEL LCA-9PC -
Transducer Techniques, Inc
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Excalibur Systems, Inc.
Accessories for the MIL-STD-1553 data bus are as much of an interface as the communication card. Therefore at Excalibur we provide a full line of accessories for the MIL-STD-1553 data bus that include, Box/Inline Couplers, Repeaters, Bus Switches, break out boxes, connectors, terminators, transformers and custom cable assemblies. Excalibur uses only premier quality parts from known manufacturers. We constantly test our products to meet our higher standards.If you have a need for an accessory product for your card and it is not listed please contact us to see if it is a product we should be supporting.
-
DAFFI MT -
DATA-PIXEL SAS
Data-Pixel has developed a cost effective interferometer line for high volumes production without compromising accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI MT to be robust, fast and accurate in order to meet all manufacturing or laboratory environments.
-
Teledyne Marine Impulse
A high density (up to 96 contacts) miniature waterproof electrical connector keeps weight to a minimum and fits into compact spaces. Well suited for underwater vehicles such as ROVs, AUVs, and UUVs, where space and weight are typical design constraints. Durable materials allow reliable connectivity with low risk of operational failure.
-
-
-