Filter Results By:

Products

Applications

Manufacturers

Connectors

dock multiple contact or data junctions.

See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly


Showing results: 1696 - 1710 of 2818 items found.

  • NI-9976, 2-Pin, Male COMBICON to 2-Pin, Female Screw Terminal Block Plug

    196739-01 - NI

    2-Pin, Male COMBICON to 2-Pin, Female Screw Terminal Block Plug - The NI-9976 consists of a bag of 10 screw terminal plugs for any 3- or 4-channel 2-position screw terminal C Series module. These terminal plugs provide direct connectivity to the module. All C Series modules ship with the required connectors, so you can purchase the NI-9976 to reduce wiring on multiple devices or use for spare replacements.

  • NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology With Column Protection Resistors

    782385-02 - NI

    The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.

  • PCI-8532, 1-Port, DeviceNet Interface Device

    781062-01 - NI

    The PCI‑8532 is a high-speed DeviceNet Interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the controller area network (CAN) physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. The DeviceNet specifications are managed by OVDA, Inc. You can program the PCI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.

  • NI 9980 10-Pos Spring Terminal (qty 10)

    197991-01 - NI

    10-Pin, Male COMBICON to 10-Pin, Female Spring Terminal Block Plug - The NI-9980 consists of a bag of 10 spring terminal plugs for any 10-position C Series module. These terminal plugs provide direct connectivity to the module. All C Series modules ship with the required connectors, so you can purchase the NI-9980 to add spring terminal connectivity, reduce wiring on multiple devices, or use for spare replacements.

  • M2T Transmitter

    Lectrosonics, Inc.

    The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.

  • 6U Processor Blade

    CP62007 - LinkedHope Intelligent Technologies Co.,Ltd.

    CP62007 is a 6U processor blade based on Intel’s 4th generation core i7/i5 processors using 22nm process technology, supporting up to four cores / eight threads at 2.4GHz. CP62007 supports up to 16GB onboard soldered low voltage DRAM with ECC. It also offers up to 64/128GB SLC/MLC onboard SATA SSD for installing operating system and drivers. The onboard design of memory and SSD enhance the anti-shock and vibration performance dramatically.CP62007’s onboard processor integrates Intel® HD Graphics 4600 controller, supporting a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA. And the VGA resolution is up to 2048x1536. With HDMI/DP/eDP outputs, the resolution can be up to “4K”.CP62007 supports 1x VGA and 2x DP/HDMI/DVI, up to 3 independent or cloned displays.CP62007 uses high speed CPCI connectors on J3 and J4 position for transferring high speed serial signals, such as PCIe2.0, USB3.0 and SATAIII. And the foot-print of high speed connectors are fully compliant with CompactPCI specifications.

  • Integrated Potentiostat and Multiplexer

    EmStatMUX8 - PalmSens BV

    Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.

  • Carrier Card

    VIPC627-ET - Abaco Systems Inc

    VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.

  • Elite™ 13.56 MHz RF Plasma Generators

    MKS Instruments

    The elite™ Series of RF plasma generators provides state-of-the art technology in a compact air-cooled package. The elite is designed with high speed closed loop control, a class E RF deck and a switching modulator for superior output performance. The elite design utilizes a single printed circuit board assembly for the full rack product virtually eliminating all internal wires and connectors and thereby providing the highest reliability available.

  • Flexible MiniPCI Express 2-Way Splitter

    SKU-059-2X - Amfeltec Corp.

    The Flexible MiniPCI Express 2-Way Splitter (Splitter) was designed to expand the modern motherboard (ATX, mini ATX, etc.) with a limited number of MiniPCI Express connectors. It allows you to connect up to two MiniPCI Express expansion add-in boards to the motherboard MiniPCI Express connector.The Splitter includes a MiniPCI Express Adapter board with a PCI Express flat cable (up to 2 boards), and MiniPCI Express host board.

  • FMC Module

    FMC1831 - Sundance Multiprocessor Technology Ltd.

    The FMC1831 is an FMC module designed to be compatible with AMC, VPX, PCI, PCIe, CompactPCI and PC/104 carriers. The module has two dual channel AD9361 transceivers with a maximum sampling frequency of 122.8 MHz over a bandwidth of 200 KHz to 56 MHz. A reference clock can be either externally supplied or be generated from an internal PLL. All input and output signals are connected via SSMC connectors for secure connectivity and signal integrity.

  • Interconnect Box

    POP 'N PLUG - ALTINEX, Inc.

    Pop-up style interconnect box with front and back connection points The Pop 'N Plug line of interconnects can "pop-up" into a raised position to provide access to connectors, or it can be lowered into a table when not in use. Pop 'N Plug interconnect boxes use a tower-type construction with a gas spring for smooth and comfortable operation. Many Pop 'N Plugs have two surfaces on either side of the unit, servicing both sides of a table.

  • LXI Microwave Multiplexer, SP4T, 10-Bank, 40GHz, 50Ω, SMA-2.92, Terminated

    60-803-510 - Pickering Interfaces Ltd.

    Our 60-803-510 is a 10 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.

  • LXI Microwave Multiplexer, SP4T, 11-Bank, 40GHz, 50Ω, SMA-2.92, Terminated

    60-803-511 - Pickering Interfaces Ltd.

    Our 60-803-511 is a 11 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.

  • LXI Microwave Multiplexer, SP4T, 3-Bank, 26.5GHz, 50Ω, SMA

    Pickering Interfaces Ltd.

    Our 60-803-303 is a 3 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.

Get Help