Showing results: 601 - 615 of 714 items found.
-
CD-2M -
Lumetronics
Is designed to carry out tests specified for Switches used for Domestic and similar applications as included under IS:3854:1997. It is used to ensure that Screwtype terminals of switches are such that they clamp the conductor without causing undue damage to the conductor strands. It is a compact and robust andequipment housed in a bench top enclosure. The CD-2M is motorized to allow easy operation. The Instrument is designed to meet the requirements of IS:3854:1997 and other related specifications.
-
Shenzhen Graigar Technology Co.,Ltd.
This power analyzer is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyser clamp is equipped with data logger.
-
Fluke 1623-2 GEO -
Iconic Engineering Limited
Fluke 1623-2 GEO Earth Ground Resistance Meter Performs stateless earth ground rod testing (two clamps). One of the most important things about Fluke 1623-2 earth tester always provides accurate results in any environment.
-
Renesas Electronics Corp.
IGBT gate drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode, signal processing circuit and power output transistor on the output side in a single chip. This coupler is designed specifically to provide high common mode transient immunity (CMR) and a high output current, and has an active miller clamp and high switching speed, making it ideal for driving IGBTs and MOS FETs.
-
Extech EX840 -
Extech Instruments Corporation
This CAT IV True RMS clamp meter features a built-in IR thermometer with laser pointer for non-contact surface measurements from -58 to 518 °F (-50 to 270 °C). Clamp measures AC current up to 1000 Amp with a maximum resolution of 0.1 Amp. The 1.7-inch jaw fits around conductors up to 750MCM. Peak hold captures motor inrush currents and other surges. Data hold and auto power off functions. Other functions include AC/DC Voltage, resistance, Type K thermometer, capacitance and frequency. Complete with test leads, Type K temperature probe, 9 Volt battery and case.
-
410130101 -
Virginia Panel Corporation
The i2 Micro iCon ITA is capable of holding up to 168 QuadraPaddle contacts. Its sleek, 0.8” footprint increases the horizontal stackability. The 30 degree U-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 0.77 in. The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
Shaqer 1500 -
HORIBA, Ltd.
The ShaQer™ offers high throughput and improved pesticide extraction for QuEChERS Sample Prep! It agitates up to six samples simultaneously compared to just two samples processed by hand. The vigorous clamp movement results in thorough extraction of pesticide residue in fruit and vegetables. Every sample is handled in the same manner ensuring consistency and eliminating variations that can occur in manual sample prep. It also accommodates a variety of tube sizes and shapes. CE Approved.
-
Shenzhen Chuangxin Instruments Co., Ltd.
Adjust the impact severity by rotating the knurled cap until the desired energy- value is displayed. Pull the knob slowly out of the device until it locks in place. If moved too fast, the clamp may skip its arrester and will lock at its way back when the pulling-force declines. Hold the device horizontally at it’s housing tube and press the (black) release cone to the specimens plane of impact. The strike is automatically released when the release force threshold is reached.
-
90061 -
HITEC Sensor Solutions Inc.
Model 90061 is a self-contained, portable measurement system which allows auditing of the pinch force generated between the electrodes of resistance spot welders. Resistance welding uses a pair of electrodes to clamp two base metals firmly together prior to and during application of electrical current. Poorly clamped parts result in a defective joint. A correctly clamped assembly aids in reducing the resistance in the joint and allows the current flow to properly heat the base metals to weld the part.
-
PCAN MicroMod FD Analog 1 -
PEAK-System Technik GmbH
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
PM7000 -
Outram Research Ltd (ORL)
It offers virtually everything needed to monitor and record power for surveys and audits. It includes 4 voltage input channels capable for measuring 0 to 600 Vac and 4 current input channels for use with voltage output current clamps, or Rogowski Coil sensors supplied. Twelve pre-stored connection configurations are set for 3 phase, 2 phase and single phase measurements. Users can also configure their own set-up and math calculation requirements and save them to non-volatile memory.
-
Split Collar Pulser Wraps -
Electro-Sensors, Inc.
Pulser wraps clamp around a rotating shaft and work with Electro-Sensors shaft speed sensors and are an ideal solution for installations where the end of the shaft is inaccessible. The two halves fasten together around the monitored shaft with recessed Allen head socket screws (provided). Standard and custom models accommodate any shaft diameter, tight spaces, and keyways. • Standard wraps operate to 3,000 rpm (high-speed also available) • Standard wraps available in PVC, aluminum, or stainless steel
-
92-965-200-M -
Pickering Interfaces Ltd.
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure that appropriate electrical safety precautions are observed.
-
410130104 -
Virginia Panel Corporation
The i2 Micro iCon ITA is capable of holding up to 120 QuadraPaddle contacts and up to 12 Micro Power or Micro Coax contacts. Its sleek, 0.8” footprint increases the horizontal stackability. The 30 degree U-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 0.77 in. The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
40-965A-050-F -
Pickering Interfaces Ltd.
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.