Showing results: 2521 - 2535 of 5211 items found.
-
System Software 4 -
BAUR Prüf- und Messtechnik GmbH
The BAUR system software is a cable fault location, cable testing and cable diagnostics package. It enables efficient maintenance of cable networks in combination with BAUR titron systems.
-
PCE Instruments
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
TDR-410 -
Sonel S.A.
*Location damaged power cables.*Fault location copper telecom cables.*Coaxial cable fault location.*Fault location wiring infrastructure.*Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.*Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
-
SC48RJ -
Whirlwind Music Distributors, Inc.
The SC48RJ Tester provides rapid, positive testing for NL4 and NL8 type multiline speaker cables, RJ45 type data cables and XLR cables.
-
Honeywell International Inc.
To install the optional cable sensor, simply plug it into the detector. The entire length of cable is an extended sensor. Additional 4 foot cable sensors (sold separately) can be connected to extend the cable and increase water sensing area even more. Note: The cable sensor jack is NOT for plugging in a power adapter. Doing so could damage the detector.**
-
SBM-1.0 -
Dynamic Load Monitoring Ltd.
The DLM Saddleback is a line tension monitor suited for more delicate cable, including telecommunication cables or large cable where a Running Line Monitor is unsuitable.
-
40-960-104-M -
Pickering Interfaces Ltd.
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell.
-
PK-102/102PL -
Pansco, Ltd
PANTESTER PRO is an advanced multifunction pin-by-pin cable tester to verify cable integrity of Datacom, Telecom and Coaxial cables and displays the test results on the main unit.
-
EE301-I2C -
Executive Engineering
Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable
-
MEET International Ltd.
*Detect through the shielded cable*Instantaneous finding of AC current*Tracing cables*Monitoring current status in applicances*Compares the AC current*Tracing cables inside the wall*Locating underground cables*Detects magnetic field*Low voltage high current detection
-
SH-TR300 -
Shenzhen Sharingtek Communication Co., LTD
Determine fiber optic cable or fiber optic’s failure point, connection point, breakpoint position -Describe fiber optic cable or fiber’s loss distribution curve, measure cable, fiber’s length and the loss, attenuation coefficient between two points-Measure fiber optic cable, optical fiber connector’s insertion loss-Measure fiber optic cable, optical fiber’s reflection loss
-
Radio Frequency Systems
Cable testing sections may be used to isolate the antenna inputs from the main feeder when testing either the antenna or feeder. These devices are normally installed between the main feeder cable and antenna inputconnector and allow access to the antenna input without the need to remove the main feeder cable. Cable test sections are particularly useful with large feeder cables that are difficult to manoeuvre.
-
Cable Nooks -
ALTINEX, Inc.
Designed for boardrooms and conference rooms, the modular Cable-Nook provides a simple and effective way of hiding/storing multimedia cables and connectors. The cables remain connected to a presentation system enabling the user to access connections to video, audio, and other media sources. The modular Cable-Nook uses a half-moon lid that remains flush with the table when not in use. To access the cables or connectors, simply lift the door and pull the cable ends out, or plug computer video cables into any installed fixed connectors. The lid closes easily even with several cables in use. After the presentation, the cable ends are returned to the Cable-Nook for safe storage.
-
Viola -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR viola. The portable and powerful viola high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 35 kV and electrical equipment. Another function is insulation testing on electrical equipment.* High performance and compact* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences
-