Filter Results By:
Products
Applications
Manufacturers
CW
Wave having a constant amplitude and frequency.
-
product
High Power Fiber Laser
Amonics' Fiber Laser (AFL) is a compact standalone turnkey equipment to deliver up to 50W output power and 1mJ pulse energy in 1064nm and 1550nm range under CW or pulse operation. Based on proprietary all fiber design, Amonics fiber laser is maintenance free. No post-installation service is required.In pulse operation, the laser delivers up to 20kW peak power and adjustable pulse width from 10ns to 1000ns. The pulse repetition rate is triggered by external TTL signal.Amonics fiber lasers are the ideal candidate for a wide range of industrial applications.
-
product
Cavity Stabilized IMPATT Oscillators
Available Frequencies: from 26.5 to 140 GHz Maximum CW power: 300 mWatt Frequency stability: from 0.05 to 0.2 MHz/C
-
product
PSG Signal Generators
Generate trusted microwave signals: get metrology-grade frequency & level accuracy with excellent distortion & spurious characteristicsRely on the highest quality signals from pure CW tones with 1 W of power to complex, vector-modulated signals with 4 GHz bandwidthReduce the time you spend on signal creation with Signal Studio softwareTake advantage of increased performance, flexibility & speed when you replace a legacy source with the code-compatible PSG
-
product
CW Transmitters
The Praxsym CW Transmitter is a complete, portable continuous wave test source. Used as an input source to test a distributed antenna system, the Praxsym CW Transmitter can provide test signals aiding in the design and optimization of in-building and outdoor networks.
-
product
Signal Processor Board
MS 1532
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
SSPAs / LNAs / Broadband
SSPAs based on the latest Galium Nitride (GaN) technology offer the best combination of high peak powers, high reliability, high efficiency, and soft degradation. High efficiency and high power are hallmarks of GaN technology, enabling SSPAs to challenge traditional tube-based amplifiers across the design spectrum. In addition the long lifetime from these devices, combined with the gradual degradation should individual devices fail, provide unparalleled service lifetime. Techniques such as bias modulation and linearization provide even better prime-power efficiency while still meeting the demanding requirements of pulsed or CW applications.
-
product
Double Ridged Waveguide Horn
DRH50
Frequency range: 4.5 GHz - 50 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: 2.40mm female Power (CW / Peak): 10 W / 20 W
-
product
Cavity Stabilized GUNN Oscillators
Available Frequencies: from 40 to 140 GHz Maximum CW power: 200 mWatt Frequency stability: 0.1 MHz/C
-
product
Double Ridged Waveguide Horn
DRH203
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
product
CW Power Measurement
Measure CW power from 10 MHz to 50 GHz at more than 17,500 readings per second over GPIB. Measure up to 90 dB with a single sensor, and select from a variety of high power sensors up to 50 W.
-
product
Infrared, Near Infrared and Raman Spectroscopy
From the very compact FTIR spectrometer to the world’s highest resolution: Bruker offers the industry's largest selection for demanding routine and High End FTIR research application including the new and unique verTera cw THz functionality.Process monitoring with FTIR / FT-NIR process spectrometers.A complete line of Near Infrared Spectrometers to fit all your needs, including Process Monitoring.FTIR Microscopy and Raman Microscopy and Spectral Imaging for high sensitivity at high spatial resolution.High spectral resolution, high performance Raman and FT-Raman spectrometers for advanced routine solutions.
-
product
DCDC
SW/CW Series
The SW and CW Series are highly efficient, single output DC/DC converters. Proportional energy transfer techniques enable these encapsulated modular converters to maintain well regulated outputs despite large variations in input voltage. The 2:1 input range makes the SW and CW Series ideal for applications where the input dc power is derived from abattery, a motor generator or other types of poorly regulated power sources.
-
product
Laser Diode
Yisinc Optical Technology Co., Ltd
Laser diode is an efficient radiation source for CW and pulsed operations.
-
-
product
Double Ridged Waveguide Horn
DRH67
Frequency range: 6 GHz - 67 GHz VSWR (max): < 1.9:1Impedance: 50 O (Ohm)Connector: 1.85mm female Power (CW / Peak): 5W / 10 W
-
product
Double Ridged Waveguide Horn
DRH40
Frequency range: 4 GHz - 40 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
-
product
General Purpose Multimeter c/w Temperature
DL9102
Double moulded housing with an oversized high contrast 2000 count LCDdisplay. Manual ranging with current range up to 20A, temperature and frequency test.
-
product
Fixed Wavelength CW Laser Source (FP) - MATRIQ
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
product
Double Ridged Waveguide Horn
DRH10
Frequency range: 740 MHz - 10.5 GHz VSWR (MAX): < 1.8:1Impedance: 50 O (Ohm)Connector: N femalePower (CW / Peak): 150 W / 250 W
-
product
Socket Tester c/w Buzzer
DL1090
Clear visual and audible indication of wiring status LED indication of a wide range of wiring conditions Designed to EN 61010 and IP30
-
product
Power Sensors
Measure CW power from 10 MHz to 50 GHz. Modulated Average Power Measurement. Peak Power Measurement.
-
product
Power Meters & Power Sensors
Keysight’s power meters and power sensors measure the power of RF and microwave signals accurately with sensors of various types (CW, average, and peak and average), covering numerous frequencies and power ranges. We offer a wide selection of power meters and power sensors for nearly all application needs — wireless communications, radar pulse measurements, component test, and more. Applications include testing the output power of communication base-station transmitters, radar system equipment, wireless devices, and much more.
-
product
Double Ridged Waveguide Horn
TEMH20
Frequency range: 1 GHz - 22 GHz VSWR (max): < 2.6:1Impedance: 50 O (Ohm)Connector: 3.50mm female Power (CW / Peak): 20 W / 50 W
-
product
Double Ridged Waveguide Horn
QRH400
Frequency range: 400 MHz - 6 GHz VSWR (max): < 2.3 :1Impedance: 50 O (Ohm)Connector: 2xN female Power (CW / Peak): 350 W / 350 W
-
product
Helix TWTs
Communications & Power Industries
• Frequency range 2 GHz to 40 GHz• Power levels up to 2.5 kW CW• Air, liquid and conduction cooling• Multiple stage collectors for improved efficiency• CW (continuous wave) & (pulsed) configurations available
-
product
Double Ridged Waveguide Horn
DRH110
Frequency Range 14 GHz - 110 GHz VSWR (AVG) <2.1 1:1Impedance 50 WConnector 1.00mm female Power (CW / Peak): 4 W / 8 W
-
product
Single Channel Peak Power Meter
8501A
The Spanawave/Giga-tronics 8501A Single Channel Peak Power Meter combine CW power measurement with the ability to make precise peak power measurements at any point on a pulsed waveform. This dual, built-in capability lets you make CW measurements and analyze pulsed waveforms with a single instrument.
-
product
Power Probes
RkT Thermopile Series
The RkT Series thermopile power probes are ideal for measuring Nd:YAG, CO2, and other mid-power lasers. The probes are designed to withstand average power densities up to 20kW/cm2 (15MW/cm2 peak pulse power density). The flat UV to far-IR spectral response allows the probes to measure broadband sources as well. Measure the power of cw sources or the average power of sources pulsed at 5Hz or greater.
-
product
Double Ridged Waveguide Horn
H-A40
Frequency range: 26 GHz - 40 GHz VSWR (max): < 1.3:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
