Filter Results:
Products
Manufacturers
Applications
CAN-FD
CAN compatible protocol with bit rates > 1 Mbit/s and 64 byte messages.
-
product
CAN FD/CXPI Communications Expansion Kit
OP-SB87FD
OP-SB87FD is an expansion board for LE-8200A/LE-8200 used for monitor/simulation of CAN (ISO 11898-1), CAN FD (ISO11898-1:2015), and CXPI (JASO D015). With this kit and the line state sheet, LE-8200A/LE-8200 works as a stand-alone type analzyer for CAN, CAN FD, and CXPI. The board supports development of CAN (used for automotive industry and other industries), CAN FD (next-generation standard of CAN providing more high-speed and communication capacity), and CXPI (invented in Japan to replace direct wirings) devices.
-
product
The all-in-one data logger for the entire vehicle networking
PM-200
The PM-200 sets the bar considerably higher on the topic of safeguarding and troubleshooting vehicles. Bus systems such as CAN, CAN-FD, FlexRay™, LIN, MOST150 and Automotive Ethernet are logged at a data speed up of to 120 MB/s. SSD removable media allow for quick evaluation and distribution of the data. Various upgrade options enable configuration for any application. Flexibility, programmability and support from debugging protocols make it possible to meet the high demands of functionality and fleet tests as well as of test runs.
-
product
Configurable System For Temperature Measurement With CAN FD Interface
MU thermocouple1 CAN FD
With the MU-Thermocouple1 CAN FD, measurement data from thermocouples are recorded, pre-processed and transmitted with CAN FD. The temperature is measured via 8 connections, which are designed for the temperature measuring ranges J, K or T, depending on the product version. Temperatures can be recorded in Celsius, Fahrenheit or Kelvin and calculated with an individual factor and offset. The measurement data is then transmitted via CAN FD or via classic CAN.
-
product
Configurable CAN FD Modules With A Focus On Digital I/Os
PCAN MicroMod FD Digital 1&2
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The main boards PCAN-MicroMod FD Digital 1 and 2 focus on digital inputs and outputs, which are provided with the appropriate protective circuit. The digital outputs of Digital 1 are equipped with low-side switches and those of Digital 2 with high-side switches.
-
product
Open Standard Module (OSM)
ROM-2820
Advantech ROM-2820 OSM 1.1 Computer-on-Module is powered by NXP i.MX 93 SoC which includes Cortex-A55 Dual-core in combination with one Cortex-M33 real time processor, Ethos®-U65 Neural Processing Unit (NPU) and 2D graphics engine. It provides USB2.0, Gigabit Ethernet, MIPI-CSI, I2C, SPI, GPIO, CAN-FD and MIPI DSI display for embedded applications
-
product
Configurable CAN, LIN And CAN FD Data Logger
Rebel CT CAN FD
The Influx Rebel CT CAN FD is a compact data logger with gateway functionality and is an ideal choice for applications that requires vehicle CAN 2.0, CAN FD and LIN network data.
-
product
TRC-8543, CAN HS/FD or LS/FT Transceiver Cable
783701-03
The TRC-8543 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8543 to the port to support a CAN HS/FD or LS/FT interface. The TRC-8543 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
product
Fanless AIoT Video Analytics Platform with NVIDIA Jetson AGX Xavier for Railway
AVA-RAGX
- NVIDIA Jetson AGX Xavier with 32 TOPs AI performance- 4xM12 GbE with PoE, 1x lockable HDMI output, 4x USB 3.0- 1x M.2 B-key for LTE/5G; 1x M.2 A/E key 2230 for Wi-Fi- 2x CAN DB-9 CAN-FD from AGX module, with isolation- Power with ignition control- Nominal Voltage: 24VDC, 36VDC, 72VDC and 110VDC (EN50155 compliant)
-
product
CAN FD interfaces and Analysers
CAN FD Interfaces and AnalysersCAN FD interfaces and analysers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
product
Universal Plug-in Module With I/O And CAN FD Interface
PCAN MicroMod FD
The PCAN-MicroMod FD is a small breadboard with CAN and CAN FD connection on the one hand and various physical inputs and outputs on the other. Both sides are logically linked using the NXP LPC54618 microcontroller. Electronics developers can use the PCAN-MicroMod FD to easily integrate I/O functionality with a CAN connection into their project.
-
product
TRC-8543, CAN HS/FD or LS/FT Transceiver Cable
783701-02
CAN HS/FD or LS/FT Transceiver Cable—The TRC-8543 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8543 to the port to support a CAN HS/FD or LS/FT interface. The TRC-8543 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
product
PCIe Mini CAN Controller
PCie-Mini-CAN-FD
The PCIe-Mini-CAN-FD is a PCI express controller with an integrated CAN FD transceiver supporting data rates up to 8Mbps. The CAN FD controller meets the specifications of the ISO11898-1:2015 high speed Controller Area Network (CAN) data link layer and meets the physical layer requirements of the ISO11898-2:2016 high speed CAN specification.
-
product
TRC-8542, CAN HS/FD Transceiver Cable
783699-03
The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is … an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
product
Configurable CAN FD Module With A Focus On Analog I/Os
PCAN MicroMod FD Analog 1
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
product
Automotive Protocol Decode/Trigger Software (CAN, CAN FD, CAN XL, LIN FlexRay, SENT) for Infiniium Oscilloscopes
D9010AUTP
- Set up your scope to show CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT protocol decode in less than 30 seconds- Support CAN XL protocol trigger and decode of the SIC mode (or slow mode) signal in the arbitration phase as well as the FAST mode signal in the data phase- Get access to a rich set of integrated software-based protocol-level triggers- Save time and eliminate errors by viewing packets at the protocol level- Use time-correlated views to quickly troubleshoot serial protocol problems back to their timing or signal integrity root causeThis application (for Infiniium Oscilloscopes) includes a suite of configurable protocol-level trigger conditions specific to CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT. When serial triggering is selected, the application enables software-based triggering. Application supports CAN-dbc symbolic debug.
-
product
Advanced Platforms
TTConnect 616
TTConnect 616 is an advanced connectivity platform that combines and manages all in-vehicle interfaces such as CAN-FD, Flexray, LIN and Ethernet. Its wealth of interfaces is complemented by advanced traffic management software and support for Time Sensitive Networking protocols, making TTConnect 616 the ideal solution for future-proof vehicle architectures where different types of traffic must converge and operate in a safe and reliable manner.
-
product
TRC-8542, CAN HS/FD Transceiver Cable
783699-02
CAN HS/FD Transceiver Cable—The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
