-
product
C-V Plotters
Materials Development Corporation
MDC will tailor your CSM/Win Semiconductor Measurement System for your exact requirements. Choose the best capacitance meter, output device, and probe station for your needs. All CSM/Win C-V plotters feature the latest Dell Computers. The computer and capacitance meters are rackmounted in one compact enclosure. When ordered with a hot chuck or probe station, MDC can deliver a turnkey system of unparalleled performance.
-
product
6kW Regenerative DC Electronic Load (CC/CR/CV/CP/CC+CV/CR+CV)
PLZ6000R
PLZ6000R is a DC electronic load that regenerates load power to the AC line. Regular electronic loads consume load power by having semiconductor devices convert it into heat. By contrast, PLZ6000R converts load power into reusable electric power, rather than converting it into heat as is typically done, and feeds this power to the AC line, thereby substantially reducing the amount of waste energy. PLZ6000R is an environment-friendly electronic load that can contribute significantly to your energy saving efforts.
-
product
Regenerative Battery Pack Test System
17020E
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
product
HEV & EV Power Tester
EVd-40
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging cons...show more -
product
Reference Electrodes
Reference electrodes are widely used as: electrochemical measurements (CV, LSV, DPV, etc.) electrochemical devices (detectors for HPLC, biosensor, etc.)
-
product
DC Electronic Load
3310G Series（75W~400W）
Each 3310G Series module has its own control and display panel, CC / CR / CV / CP / Dynamic modes, plug in 3302G / 3305G / 3300G mainframe with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
product
High voltage Flexible range Regulated DC Power Supplies
PSF-H Series
* Main Applications: High-voltage capacitors or relays used for hybrid cars, electric cars, solar power system and high-voltage LED lighting equipment.* 6 times of flexible output range: PSF-800H covers output for several units of conventional type regulated power supplies within 800W ( max voltage 800V, max current 6A. ).* Constant Power Control: CP mode is available in addition to CV and CC modes.* Changeable setting style: Vertical or horizontal setting by 90rotating panel.* Sequence Operat...show more -
product
Ferroelectric Tester
Premier II
The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.
-
product
High Power DC Electronic Load
34000C Series（6KW~24KW）
34000C Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
product
Electronic Loads
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
product
Electronic Loads
Flexible electronic DC loads for general purpose applications. Voltage up to 80V, current up to 80A and power up to 600 watts. CI, CR, CG, CV and CP modes, built-in transient generators. Models with USB, RS232, GPIB and LXI compliant LAN interfaces.
-
product
DC Electronic Load
3110 Series（250W~700W）
Each 3110 Series stand-alone load has its own control and display panel, CC / CR / CV / CP/ Dynamic modes, also can be controlled intranet via RS232 and USB interface.
-
product
Load Banks
PT04 Series
Quality ProductRugged and Reliable DesignCurrent control from 0 to 70A on 64V RangeCurrent control from 0 to 135A on 32V Range4kW plus rating (at 40°C ambient)Cost effective; simple robust designCC, CP, CR and CV modes as standardCurrent control from either ATE with0 – 5V demand input or from a RemoteControl Box (both standard)Ultra Low electrical noiseSelectable Range 64V or 32VTemperature controlled quiet fans19 Inch Rack case 4U
-
product
Cryogenic Probe Station
CPX-VF
The Lake Shore CPX-VF probe station enhances the standard probe station capabilities with the addition of a ±2.5 T vertical field superconducting magnet. It can do all the standard C-V, I-V, microwave, and electro-optical probing of the CPX, plus out-of-plane vertical field superconducting magnetic measurements. Researchers can use it to perform Hall effect measurements and test magneto-transport parameters. The CPX-VF is one of Lake Shore’s premium probe stations for combining microwave measurements with magnetic field.
-
product
High Power DC Electronic Load
3350G Series（4KW~6KW）
Each 3350G Series module has its own control and display panel, CC / CR / CV / CP /Dynamic modes, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
product
Electric Load
PT04-250-63
For Telecom Rectifier and Power Supply testing. *0 to 63A up to 250V, power limited to 1,900 Watt *CC, CP, CR and CV as standard *63A available Load down to 5.3V
-
product
High Slew-Rate High Power DC Electronic Load （100A/μS）
34110A-11（10KW）
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
product
High Power DC Electronic Load（1250V）
36300E Series（50KW/60KW）
36300E Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
Software
Production C-V Measurement
Materials Development Corporation
The production software offers a streamlined C-V plotting and bias-temperature stress program with minimumoperator input. A single keystroke begins the measurement.
-
product
LED Load Simulator
63110A/ 63113A/63115A
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is ...show more -
product
Digital Control DC Electronic Load
IT8200 Series
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
product
High Performance High Power DC Electronic Load
IT8900 Series
IT8900 series of high performance high power dc electronic loads provide three voltage ranges 150V/600V/1200V. The power expands to 600kW by master-slave paralleling, and maintains stand-alone functions. 50kHz high speed measurement, six working modes, transient over-power loading capability, CV loop speed adjustment, Measurement function, 25kHz dynamic test and other multiple accurate testing functions make IT8900 series well-suited for types of high power applications.
-
product
Software
MOS Doping Profile Analysis
Materials Development Corporation
MDC uses the comprehensive Ziegler algorithm toconvert pulsed MOS C-V data to a doping profile. The doping profile is accurate from the oxide semiconductor interface to the maximum depletion depth and is therefore useful for low dose ion implant monitoring. Peak doping, range, and total active dose are computed. The technique is sensitive enough to resolve changes in the substrate doping profile due to redistribution during oxidation.
-
product
Mini Digital Clamp Tester (CE)
M-140HC
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy!:Measurale Load Current at high voltage CV/CVT cables with grounding lines for shield phase.*Epoch-Making!:Can measure phase current of CVT cable just by putting CT head on to the conductors as well as CV cable just by clamping CT to the conductors in a lump.*Low Cost!:Can measure line/leakage current in the same manner as ordinary clamp meters.
-
product
LED Test Programmable DC Electronic Load
IT8912E Series
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
product
Electronic Yarn Count System
Y006
Consists of an electronic balance (220 grams x 0.001 grams) with internal and external custom software which calculates yarn, sliver and roving counts as well as fabric yield in various systems and provides statistics on any number of tests including totals, average, CV and SD
-
product
Semiconductor Device Parameter Analyzer and Measurement Modules
B1500A Series
Keysight B1500A Semiconductor Device Analyzer of Precision Current-Voltage Analyzer Series is an all in one analyzer supporting IV, CV, pulse/dynamic IV and more, which is designed for all-round characterization from basic to cutting-edge applications. It provides a wide range of measurement capabilities to cover the electrical characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised meas...show more -
product
Automotive & Industrial Cycle Testing System
CV
The CV is Bitrode's economical cycle life test equipment for the network based line of battery laboratory equipment. Designed to work with VisuaLCN Lab Client software, the CV provides standard or fully customized charge, discharge and rest cycles for automotive and industrial batteries. The Model CV is also useful for reserve capacity and charge acceptance testing with recharge.
-
product
Programable DC Power Supply
ADG-L Series
14 models and three different output power, 4kW, 8 kW and 12 kW. Utilizing PWM technology, ADG-L delivers stable output and precise measurement. With CV, CC and CP mode, ADG-L series is ideal for Photovoltaic, Electric Vehicle, battery, fuse/capacitor and third party laboratory testing.
-
product
160W DC Programable Power Supply
*Source effect: CV≤0.01%+3mV(mA)*Load effect: CV≤0.01%+3mV(I≤3A) CC≤0.2%+3mA(I≤3A) CV≤0.02%+5mV(I>3A) CC≤0.2%+5mA(I>3A)*Ripple and noise: CV≤1.0mVrms(I≤3A) CC≤3mArms(I≤3A) CV≤2.0mVrms(I>3A) CC≤6mArms(I>3A) *Protection Type: Overcurrent Protection (OCP) Overvoltage Protection (OVP)* Display accuracy: Voltage indication accuracy: ± (0.5% + 2 words)
