- Pickering Interfaces Inc.
product
96-Pin Micro-D Connector Block, Female With Screwlocks
40-965-096-F
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
MICROBLAZE Processor Board
MS 1536
- Virtex 4 FPGA with Embedded PowerPC 405 (PPC405) Core- Up to 450 MHz operation- Tri-mode Ethernet Media Access Controller- A/D Converter Blocks (10-bit / 200 kilo samples per second)- Select IO Technology (Wide selections of I/O standards from 1.5V to 3.3V)- DDR2 SDRAM (256MByte)- Program Storage Flash Memory (8MByte)- Data Storage Flash Memory (8MByte)- Vertex-4 FPGA PROM (4MByte)
-
product
RF & Microwave
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and attitude to utilise the latest technologies.An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements. A list of products is given below.
-
product
PowerPC 405 Board
MS 1533
- Virtex 4 FPGA with Embedded PowerPC 405 (PPC405) Core- Up to 450 MHz operation- Tri-mode Ethernet Media Access Controller- A/D Converter Blocks (10-bit / 200 kilo samples per second)- Select IO Technology (Wide selections of I/O standards from 1.5V to 3.3V)- DDR2 SDRAM (256MByte)- Program Storage Flash Memory (8MByte)- Data Storage Flash Memory (8MByte)- Vertex-4 FPGA PROM (4MByte)
-
product
PXIe-4310, 16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module
784813-01
16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module—The PXIe-4310 is a channel-to-channel isolated, filtered analog input module for higher voltage measurements. The module offers the ability to select an analog filter per channel to provide extra filtering performance. You also can operate up to four different input ranges per terminal block and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI-DAQmx driver simplifies hardware configuration and measurement.
-
product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix Topology Without Column Protection Resistors
782385-07
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
TB-2635, Screw Terminal, 8x16, 2-Wire PXI Module Matrix Terminal Block
778839-01
Screw Terminal, 8x16, 2-Wire PXI Module Matrix Terminal Block - The TB-2635 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 2-wire 8×16 matrix. You can directly connect the TB-2635 to the front panel I/O connectors of the PXI-2529. The TB-2635 includes screw terminals that provide access to the rows and columns of the matrix.
-
product
TB-4310 Front Mount Terminal Block for PXIe-4310, +/-600V Input
785022-01
96-Pin Female DIN to 82-Pin Female Screw Terminal, 10 V/600 V, PXI Module Mount Terminal Block.
-
product
75-Watt DC/DC Converter; Triple Output
55KT1
NAI’s 55KT1 is a 75-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power, triple output, at a baseplate temperature of +100° C.
-
product
TB-2676, Ribbon, 100 V, PXI Module Multiplexer Terminal Block
779535-01
Ribbon, 100 V, PXI Module Multiplexer Terminal Block - The TB-2676 features ribbon cable headers that help you access all channels of the PXI-2576 Multiplexer Switch Module. You can use the TB-2676 to configure the 16 banks of 4x1 2-wire multiplexers included with the PXI-2576.
-
product
125-Watt DC/DC Converter, 3U cPCI
55LQ3
NAI’s 55LQ3 is a 125 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
product
+5 VDC to +3.3 VDC 75-Watt Converter 6U VME
44KS2
NAI’s 44KS2 is a 75-Watt DC/DC Converter that plugs directly into a standard 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +5 VDC input and converts it to a single +3.3 VDC output at 75 Watts. The 44KS2 is ideal for powering single board computers or any other devices that require +3.3 VDC.
-
product
NI TB-2646B Terminal Block for NI 2532B as 1-Wire Quad 4x32 or 2-Wire Dual 4×32 Matrix Matrix Topology Without Column Protection Resistors
782385-13
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
TB-2631B , Term Block for NI PXI-2530B 4x32 1W or 4x16 2W Matrix
781688-01
The TB-2631B provides a PXI front-mounting terminal block to configure the PXI-2530B PXI Multiplexer Switch Module. It provides direct signal wire connections to the screw terminals inside the terminal block.
-
product
400 Watt DC/DC Converter, 3U VPX, Holdup Time
VPX68
NAI's VPX68 is a rugged and high-efficiency 400-Watt Output +28 VDC Input 3U VPX DC/DC converter designed for aerospace, defense, and industrial markets. It is an off-the-shelf power supply with optional integrated Holdup Time that plugs directly into a standard VITA 62 conduction cooled chassis. The power supply, engineered to meet harsh environmental conditions, includes continuous Background Built-In-Test (BIT), I2C communication, remote error sensing, and protection against Input transients, over-voltage, over-current, and short-circuits, ensuring reliable and consistent performance.
-
product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
PXI-2800, 4-Slot PXI Carrier Module for SwitchBlock
781420-00
4-Slot PXI Carrier Module for SwitchBlock - The PXI‑2800 is a carrier module for SwitchBlock that can hold up to six SwitchBlock relay cards while occupying four PXI slots. By connecting multiple SwitchBlock relay cards through the carrier’s integrated analog bus, you can easily create large matrices with more than 2,000 crosspoints in four PXI slots and more than 8,000 crosspoints in a single PXI chassis.
-
product
Digital Synchro and Digital to Resolver
DSN-DRN
Computer Conversions Corporation
The DSN - DRN Series are highly reliable, miniature, narrow profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
product
725-Watt (270VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX57HS
NAI’s VPX57HS-31 is NAI's latest +270 VDC Input, VPX DC/DC Converter. The VPX57HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
product
50-Watt DC/DC Converter; Single Output
55JS1
NAI’s 55JS1 provides full-power, single output at a baseplate temperature of +100° C.
-
product
Isolated DC-DC Converters
power supplies that convert one DC voltage level to another while maintaining galvanic isolation between the input and output circuits.
-
product
PXI 8/16-Channel Isolated D/A Converter
M9185A
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
product
Optical to Electrical Converters
High bandwidth, broadband optical to electrical converters available in a range of configurations. Choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
Synchro to DC Converters
Computer Conversions Corporation
This unique series of Synchro to DC Converters makes use of advanced digital circuitry techniques to accomplish high speed conversion with extreme accuracy. Transformer isolation as well as balanced line-to-line input impedance is provided for superior and trouble-free system performance, regardless of the input synchro used.
-
product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix Topology Without Column Protection Resistors
782385-11
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix topology With Column Protection Resistors
782385-04
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
product
TB-2636, Screw Terminal, 4x32, 2-Wire PXI Module Matrix Terminal Block
196762-01
The TB-2636 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 2-wire 4×32 matrix. You can directly connect the TB-2636 to the front panel I/O connectors of the PXI-2529. The TB-2636 includes screw terminals that provide access to the rows and columns of the matrix.
-
product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors
782385-06
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Optical-Electrical Converter - MATRIQ
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
