Filter Results By:

Products

Applications

Manufacturers

Band

spectral range designation of a frequency range or wavelengths.

See Also: C-band, Ka Band, E-band, Ku band, L Band


Showing results: 826 - 840 of 848 items found.

  • 5G 256-Element Active Antenna Innovator’s Kit

    AWA-0134 - Anokiwave Inc.

    The AWA-0134 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0134 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.

  • Reconfigurable Filter Bank

    BSC Filters

    BSC have independently developed a fully reconfigurable adaptive filter solution, designed for fast & seamless switching into any of 256 filter states across the 2-18 GHz range.  Ideally suited to EW front-end preselection or protection, any combination of bandpass and bandstop states can be selected INTRODUCTION.  Each 2 GHz channel can be switched in (bandpass) and out (bandstop) of the signal path with a switching time of less than 100 ns. DC power and 8-bit TTL control is supplied through a standard 15-pin MDM connector. In the crowded spectrum of the future, front-end flexibility is of increasing importance. Not limited to 2-18 GHz or equal channel widths, the same core architecture may be used in more specific bands, for example at VHF/UHF frequencies. This makes the system equally as suited to EW as it is to Mil Comms applications, where sampling sensitivity or frequency-agile protocols respectively are key to system function.

  • Waveguide Bends

    Fairview Microwave Inc.

    Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.

  • Bench PIM Tester - iBA series

    iBA - Kaelus

    Passive Intermodulation (PIM) occurs when multiple RF signals encounter defects in materials or workmanship in an RF path. These defects behave like a mixer causing noise to be generated at mathematical combinations of the original carrier frequencies. PIM interference that falls in the receive band of a wireless system elevates the noise floor resulting in high dropped call rates, call blocking, slow data transmission speeds and decreased system capacity.Kaelus is the industry leader in Passive Intermodulation test solutions. Since 1996 Kaelus has supplied RF equipment manufacturers around the world with precision IEC compliant test equipment to perform this critical test. From initial product design through high-volume manufacturing, Kaelus offers a wide range of PIM test solutions that enable equipment manufacturers to quickly and confidently verify the performance of their products.

  • Amplifiers

    Becker Nachrichtentechnik GmbH

    Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.

  • Analogue (1kV below) Insulation Tester

    2732 IN - Standard Electric Works Co., Ltd

    ● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.

  • Analogue (1kV below) Insulation Tester

    4132 IN - Standard Electric Works Co., Ltd

    ● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.

  • Field Strength Meter

    FIM-71 VHF - Potomac Instruments, Inc.

    The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of either 20 dB or 60 dB. A dc analog output voltage, proportional to the meter indication, is provided for driving a chart recorder. A leveled output from the calibrating oscillator is available for measuring cable insertion loss, filter response, amplifier gain, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.

  • Field Strength Meter

    FIM-72A UHF - Potomac Instruments, Inc.

    The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.

  • Systems Integration for Circuit Card Assembly

    Teledyne Defense Electronics

    Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required

  • Medium-size Reverberation Chamber

    E-Series - Emite Ingeniería SL. Ed

    The E medium-size multicavity Reverberation Chamber Series represents that state-of-the-art in reverberation chamber technology. The E-Series can make single measurements, batch tests, protocols or campaign tests for different frequency bands, different technologies and different channel models, running overnight without human intervention. Embedded frequency-, mode-, source- and platform-stirring in a double-shielded set of cavities allow Passive MIMO (Efficiency, Correlation, Diversity Gain, MIMO Capacity and others), Active MIMO OTA (TRP, TIS, TPUT, MTS, CQI, M2TxDT, RSRP, MCL and others) and Time-Domain MIMO (DL/UL TCP/UDP TPUT, RMS DS, STD, PL, CBW, Mute%, eNodeB, VDT-OTA) measurements up to 8x8 and 8DLCC to be performed for antennas and devices up to 50cm and 50kg ranging from 2G to 4G, covering all available cellular and wireless technologies to date, including wearables devices, sound acoustic mute, WLAN and W-IoT testing. There is no RC in the market more advanced than the E-Series.

  • Outdoor AGC Optical Node

    SR814WB - Hangzhou Softel Optic Co., Ltd.

    *SR814WB series of 1310nm optical relay station is a two-way optical connector with HFC network engineering experience and equipment development experience accumulate for many years by ourselves only for HFC two-way Broadband Network. This product is designed with full consideration of network topological structure.The building block system modularized structure is adopted in SR814 Series *Field Optical Work station. It has flexible configuration and convenient debugging, and solves engineering and technical problems of collecting noise with two-way return path network. And it meets the requirements of modern CATV business network security transmission with high reliability of FTTB (Fiber to the Building).*SR814W Band SR814WB Optical Workstation are four way independent output models; WR-8604HB and WR-7504HB Optical Workstation are two way independent output models.*SR814W BOptical Workstation is our latest flagship product. Advanced optical AGC control circuit adds to the part of optical receiving to ensure the input optical power as low as -9dBm.

  • 5G Active Antenna Innovator’s Kit

    AWMF-0129 - Anokiwave Inc.

    The AWMF-0129 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +50dBmi output power while consuming just 12W DC power in the RF circuits and has achieved Gb/s data rates in OTA trials. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWMF-0129 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.

  • AERINOS ProfiSens IOT

    Infinite Industrial Informatics Lt

    AERINOS® ProfiSens is a local area wireless IOT platform. It comprises wireless sensor nodes and a 3G Data Concentrator/ Gateway. Using ProfiSens, you can deploy anywhere your own IOT network. The battery powered, wireless End nodes, offer reliable communication and outdoor enclosures to satisfy a variety of measurement and monitoring applications. The acquired sensor data wirelessly transmits to the data concentrator with 3G, GSM/GPRS connectivity, which forwards data files to an FTP server and alarm SMS to predefined users.The coverage of the wireless network can reach a radius of 1-6 km (Line of sight). The platform is available for the 433 MHz license free band and optional for the 868 MHz and 915 MHz bands.The wireless network uses a proprietary protocol with bidirectional communications. The sensor nodes are frequently synchronized by the data concentrator in order to achieve real time data collection with a fixed update rate of 5 minutes. Data concentrator and sensor end nodes support autonomous battery powered operation and provide options for external power supply.

  • Fiber Optic Test System

    OPTOWERE-S100 (Fiber Optic Test System) - Notice

    The frame of FOTS system consists of the Main control part and the Slot mounting part. The Main control part is in charge of control and interface of the system and the Slot mounting part can hold up to maximum 8 slots, which are modularized according to each function and come out in five kinds. This integrated test system is designed to help manage the test and measurement related to optical communication and component. And the modular architecture of FOTS allows for customized configuration so that the slot of LD Driver, 2 channel VOA, 1 X 4 switch, WDM EDFA and C + L – Band ASE Source can be chosen according to user’s necessities. Main control part and each function module are run by effective and multi-functioned system control program in the base of high speed remote interface, GUI display and the discriminative high speed driving of module and system. This system can provide variety manufacturing and laboratory applications such as general quality test and reliability test of optical component and optical signal transmission test through efficient linkage with other system.

Get Help