Showing results: 196 - 210 of 270 items found.
-
K- AN8 KIT -
Influx Technology LTD
This K-AN8 (8 analog + 4 digital input) kit contains everything needed to get the K-AN8 set up and tested on a work bench.To help with connecting sensors to the analog and digital ports the K-BoB enables easy connection with BNC connectors.Influx K-Cal is easily connected via the Kvaser LeafLight interface and Kvaser T-CANnector. (Using the Kvaser T-CANnector to power up the K-AN8 (at the desk) and terminate the CAN bus).
-
Fairview Microwave Inc.
RF detectors from Fairview Microwave are available with N Type or SMA connector series inputs and BNC or SMA connectors for outputs. Fairview RF detectors are zero bias Schottky diode and have negative video out. These zero bias Schottky diode detectors for RF have a minimum frequency between 10 MHz and 2 GHz and maximum frequency range between 2 GHz and 26.5 GHz.
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless GPS Signal Splitters are available in 2-way thru 48-way configurations spanning 1-2 GHz with unpeered performance in GPS (L1-L5), GNSS, Galileo, GLONASS, BeiDou, and IRNSS antenna splitting applications. The 200 ohm internal load on the DC-blocked port(s) prevents receivers from incorrectly sensing an antenna fault when there is no current draw. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
8471D -
Keysight Technologies
The Keysight 8471D is a low-cost, planar-doped barrier detector offering excellent performance to 2 GHz. A negative polarity output is standard, and a positive polarity is available as Option 103. A load option (Option 102) extends the square-law region to at least -10 dBm. The Keysight 8471D has a BNC (m) input connector and a frequency range of 100 kHz to 2 GHz, making it ideal for use in RF and low microwave applications.
-
ViTec Co. Ltd
The system is designed to collect data during model tests in a pilot pool.The complex is built on the basis of a laptop in a protected design, a National Instrumrnts data collection board and two external connector blocks with BNC connectors, allowing you to connect up to 32 analog signals.
-
T3CP Series -
Teledyne LeCroy
Teledyne Test Tools AC/DC Current Probes are powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range of five current probes includes models with bandwidths up to 100 MHz, peak currents up to 500A and sensitivities to 1 mA/div.
-
Arrow Tech
Probe has a mica window that has a thickness of 1.8 to 2.0 mg/cm2. This allows detection of alpha radiation as low as 3.0 MeV when in close proximity to the window. Beta radiation in excess of 35 keV and X-ray or gamma radiation greater than 6 keV can also be deteched. The detector is provided with a BNC connector. It can be used with most count rate and survey meters which accept Geiger Mueller (GM) detectors operating at 900V DC.
-
7415-3 -
Solar Electronics Company
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
Metrix
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
CDN -
EMCTEST
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
RkP-400 Series -
Laser Probe Inc.
The RkP-400 Series probes consist of a compact head containing the detector and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1” (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
COND25-1553 -
Abaco Systems Inc
Commercial Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends. Military Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and two 18" cables with BNC cable jacks for I/O triggers.
-
RjP-400 Series -
Laser Probe Inc.
The RkP-400 Series probes consist of a compact detector assembly, or head, and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1" (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
T010-001-K -
Tripp Lite
The T010-001-K Multi-Function Cable Tester is an essential tool for cable installers or anyone working in telecom or LAN environments. It allows you to test RJ45 (STP/UTP), RJ11, BNC and USB cable wiring, length, fault and location, as well as common metal wires using the included alligator clip adapter.
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
ZT-01 features its unique configuration, because of which many places can be inspected conveniently. For example, it can test the patch cord directly. It can work with either male connector ends or inspect through female bulkhead adapters. As a result, many hard-to-reach connectors that are installed on the ‘backside’ of patch panels or inside hardware devices can be easily inspected. It eliminates the need to access the backside of patch panels or disassemble hardware devices, bringing more convenience to the inspection. BNC interface output