Audio Cable Testers
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
Audio Cable Testers
AudioJog Pro 3
-
Audio cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection .
-
Product
12 Plug Pro Audio Cable Tester
PCT40
-
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
8 Plug Pro Audio Cable Tester
PCT10
-
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections3.5mm TRS Jack1/4' TRS Jacks3 Pin XLR Male3 Pin XLR FemaleRCA Phono4 Pin SpeakonBanana Plugs9V Batter (Not Included)
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Performance Audio Analyzer
U8903B
Audio Analyzer
Measure your most demanding audio devices with higher accuracy and a low residual distortion of -110 dB See the real performance of your devices with the highest resolution audio measurements available Automate testing with built-in test sequences Meet standards more easily with pre-configured POLQA and PESQ measurements Simultaneously measure/view up to eight channels on a single screen in real time Configure for specific applications with digital audio interface (AES3/SPDIF and DSI) and Bluetooth audio measurements options
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Sound Harmonics and Current Analyzer
H74050100
Audio Analyzer
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
MS-M 26-Pin RF Cable Assembly 0.5m
40-979-526-0.5m-FU
Cable Assembly
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
100 Pin Micro-D Cable, Male to Male, 1m 2-56 UNC Screwlocks, Metal Shell
A100SMR-100SMR-9A100
Cable Assembly
This 1m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
Product
Cable Assembly, Receiver, Mini Coax, 36", 4 SMB Plugs
540104010207
Cable Assembly
Cable Assembly, Receiver, Mini Coax, 36", 4 SMB Plugs
-
Product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to Female (Female Screwlocks), 0.5m
40-970B-200-0.5m-FF
Cable Assembly
This female to female 0.5m cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cable and the connector assemblies can be secured to their mating connectors by female screwlocks.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 78-Pin Female D-Sub
540034010229
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 36", 2 78-Pin Female D-Sub
-
Product
Cable Assembly, Receiver, Micro Coax, 20", 18 MCX Plugs And 2 SMB Plugs
540102010147
Cable Assembly
Cable Assembly, Receiver, Micro Coax, 20", 18 MCX Plugs and 2 SMB Plugs
-
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 0.5m, Screwlocks
A068SMR-C-6B050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
20-Pin GMCT Cable, Male to Male, 10A, 2m
A020GMR-020GMR-0B200
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly 44-Pin D-Type Male to Unterminated With Tinned Ends, 1m
A044HM5-T-0A100
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Cut Ends
A078HF4-C-0A100
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends
A050DF4-T-0A200
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
