Filter Results By:
Products
Applications
Manufacturers
Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
product
Analog I/O Interfaces
United Electronic Industries, Inc.
24 differential analog input channels Maximum sampling rate of 1000 Hz per channel 18-bit resolution ±3 µA accuracy 350 Vrms Isolation Dynamic autozero support Embedded averaging engine
-
product
OMNIBUS Analog I/O Modules
I/O Mezzanine cards for Modular, Solomente & Data Acquisition boards
-
product
Multifunction Analog I/O Card
LPCI-AIO16A
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
product
Analog I/O and Digital Receivers
Curtiss-Wright Defense Solutions
Many mission-critical applications require small form factor solutions, but cannot compromise ruggedization requirements or I/O and processing performance. Our VPX, XMC, PMC and FMC module-based sensor I/O solutions are designed to handle the toughest operating environments while packing maximum functionality in a minimal physical footprint.
-
product
Analog I/O module with 32/16 multiplexed analog input channels
IO102
Fast 16-bit analog module with 32/16 multiplexed analog input channels and 4 analog output channels. This I/O module offers lower input sampling and conversion times than the IO101 and therefore leads to smaller overall driver latency time. It is similarly priced as the IO101 but comes with 4 analog outputs instead of 8.
-
product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
product
Analog I/O module 24-bit sigma-delta
IO109
High-resolution 24-bit sigma-delta analog module with 12 differential analog input channels. This I/O module is a high-end low-noise analog module with a very high input resolution of 24-bit. Each analog input channel is equipped with its own dedicated DC-coupled Sigma-Delta A/D converter for sample rates up to 200kSamples/s.
-
product
Analog I/O module with a input and output resolution of 16-bit
IO104
Very fast 16-bit analog module with 8 simultaneous-sampling analog input channels and 4 analog output channels. This I/O module is a high-end analog module with a input and output resolution of 16-bit. Because each analog input channel has its own dedicated A/D converter signals are sampled truly simultaneous and the conversion of up to all 8 analog input channels is constant (500ns).
-
product
Rugged Analog I/O Modules
Our extensive line of analog I/O modules currently includes PC/104, PCIe MiniCard and FeaturePak form-factor products, providing both A/D and D/A functions. Most of these products also include digital I/O and counter/timer features. A unique feature of Diamond analog I/O modules is our patented autocalibration technology, which can reduce analog measurement errors by up to 10 times relative to conventional designs.
-
product
Analog I/O Module
DS-MPE-DAQ0804
The DS-MPE-DAQ0804 is a rugged, low cost data acquisition PCIe MiniCard module with both analog and configurable digital I/O. It is ideal for adding analog I/O and digital I/O features to embedded and OEM applications requiring low cost, small size, and/or light weight.
-
product
Analog I/O Module with 16 single-ended analog output channels
IO111
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 3µs. The output coupling of the module is single-ended for all channels. The output range of each channel can be selected individually.
-
product
Multifunction Analog I/O Board
104-AIO12-8
*Eight true differential inputs, or eight single-ended inputs optional*Programmable input ranges of: 0-5V, 0-10V, ±5V, ±10V*100KHz sampling rate*On-board pacer clock and counter timers*Four double-buffered analog outputs*Jumper selectable output ranges of: 0-5V, 0-10V, ±5V, ±10V*24 digital I/O lines, type 82C55 with change of state detect on port C, buffers on ports A & B*Flexible configurations to suit your needs
-
product
PXIe-6386, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785926-01
PXIe, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6386 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6386 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCI/Universal PCI Bus DAQ Products
ACCES' PCI/PCI-X bus data acquisition and control (DAQ) cards are designed to cover the most common industry applications. Our full selection of PC-based plug-in analog and digital I/O, multifunction, isolated, relay, serial, and watchdog cards guarantees we'll have a product to match your application. The broad availability of the PCI bus makes it one of the most popular options for industrial/rack-mount DAQ systems. If you don't see what you need, ask us and we will make it for you.
-
product
PXIe-6378, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781476-01
PXIe, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6378 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6378 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
cDAQ-9174, 4‑Slot, USB CompactDAQ Chassis
781157-01
4‑Slot, USB CompactDAQ Chassis - The cDAQ‑9174 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9174 also has four 32‑bit general-purpose counters/timers. With multiple timing engines, you can run seven hardware-timed operations simultaneously, with three independent rates for analog input.
-
product
PCI-6143, 8 AI (16-Bit, 250 kS/s/ch), 8 DIO, PCI Multifunction I/O Device
778913-01
The PCI‑6143 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6143 is ideal for a variety of applications, such as … high-energy physics, ultrasonic and sonar testing, ballistics and highly transient signals, and multiaxis control. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
FMV Compression System
daq8580
The Daq8580 is designed to address the challenges of processing, transporting and storing full motion video through video encoding, and can interface with a wide variety of analog and digital I/O and process standard video formats up to 1080p30 as well as computer resolutions up to 1600x1200.
-
product
USB-6351, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
781440-01
16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6351 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6351 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
cDAQ-9185, 4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785064-01
4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9185 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
product
PCI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device
779111-01
32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device - The PCI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Analog I/O module with 8 differential analog output channels
IO108
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 8 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
product
PXIe-6355, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783632-01
PXIe, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6355 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6355 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
USB-6003, 8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device
782608-01
8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device - The USB‑6003 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32‑bit counter. The USB‑6003 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB‑6003 with screw-terminal connectivity. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCIe-6374, 4 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, Multifunction I/O Device
785817-01
The PCIe‑6374 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6374 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included DAQExpress™ companion software provides basic measurement and analysis, while the NI‑DAQmx driver provides the ability to create customized automated measurement and control applications.
-
product
PXIe-6259, PXIe, 32 AI (16-Bit, 1.25 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
779778-01
The PXIe-6259 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
781443-01
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCI Express Mini Card With 16 S.E./8 Diff'l Analog Inputs And 4 Analog Outputs
mPCIe-AIO16-16F
The mPCIe-AIO16-16F is an ideal solution for adding high-speed analog I/O capabilities to any computer with an mPCIe slot.
-
product
PCIe-6320, PCI Express, 16 AI (16-Bit, 250 kS/s), 24 DIO Multifunction I/O Device
781043-01
PCI Express, 16 AI (16-Bit, 250 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6320 offers analog input, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6320 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Hybrid, Multifunction I/O
779639-01
32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
