- Pickering Interfaces Inc.
product
25 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
25 Channel Potentiostat/Galvinostat
ArrayPGstat
For any selected cutoff voltage or current, early finishers are held at open circuit until all cells complete the charge or discharge period. All cells are switched at identical state-of-charge.- Multichannel potentiostat/galvanostat- Compliance voltage ±15 V- Voltage control ±10 V- Waveform signal sources (4 maximum)- ±100mA/channel (40 channels maximum)- 8 kHz bandwidth- Maximum scan rate 100 V/sec- Battery charge-discharge cycling: Time and/or voltage switching parameters.
-
product
Receiver, 9025, 25 Module, Single Tier
310104420
The 9025, 25-module receiver, is designed to fit into a standard 19” rack. It is equipped with a locking handle to ensure your contacts are engaged. A standard integrated microswitch shuts off power when the ITA disengages from the receiver.
-
product
ITA, 9025, 25 Module, Single Tier
410104111
Supports a maximum load of 787 lbs to achieve .030" total deflection.
-
product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
25 Pin 1.27mm Pitch Micro-D Cables - 25 Pin Connector to Alternative Connector
The connector to connector cable assemblies below are suitable for high-density applications including Pickering’s LXI DIO/Trigger port.
-
product
PXI 25 x DPST Electromechanical Relays
40-146-002
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D to 25 Pin D-Type, Female to Male, 1.8m, Economy
A025CFR-025DMR-ZA180
This economy 1.8m long female 25-Pin Micro-D to male 25-Pin D-type cable assembly is constructed from 7/36 (28 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
25 Pin D-Type Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
product
Oscilloscope 25 GHz, 4 Channels, 1mm Inputs
UXR0254BP
UXR0254BP Infiniium UXR-Series is the 5 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
product
Optical Fiber 1×25 Switch
OFSW - 1 × 25
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×25 is a 1×25 prism optical switch. It can support 1 optical fibers input and 25 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
25 Pin 1.27mm Pitch Micro-D Cables - 25 Pin Connector to 25-Pin Connector
The connector to connector cable assemblies below are suitable for high-density applications including Pickering’s LXI DIO/Trigger port.
-
product
Oscilloscope 25 GHz, 2 Channels, 1mm Inputs
UXR0252BP
UXR0252BP Infiniium UXR-Series is the 25 GHz, 2 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
product
9025TR - 25 Module Solution with Platform
The 9025TR has over twice the I/O as the G12 and is outfitted with the same 20-inch platform to support enclosures while engaging and disengaging. The front-mount ITA is user-friendly, allowing the enclosure or fixture to be fastened from the mating side. The docking feature of the 9025TR provides an easy way of guiding a fixture into position prior to engagement. Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR uses all standard modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit.
-
product
Digital Channel, 10 MΩ Input, ±25 V, 8 Channel
CX1152A
The CX1152A Digital Channel provides 8-channel digital trigger for the CX3300 Device Current Analyzer series, which is useful when a low power device with digital I/Os is evaluated. Only the CX3324A mainframe has the interface of this product. The input impedance of each channel is 10 MΩ in order to minimize the load current from the digital channel.
-
product
Cable Assembly, Receiver, 20", TriPaddle, to 25 Pin Female D-Sub
540014010101
Cable Assembly, Receiver, 20", TriPaddle, to 25 Pin Female D-Sub
-
product
Current Measurements of PWM or Inverter, AC/DC 25~500A, φ35mm
CTF-500DC
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 25~500A*Current measurements for PWM or inverter
-
product
Infiniium UXR-Series Oscilloscope: 25 GHz, 4 Channels
UXR0254A
The UXR0254A is the 25 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope.
-
product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, .25 Meter
187252-0R25
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
product
Receiver, 9025TR, 25 Module, with 20" Platform
310104435
Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR can be adapted to accommodate vacuum or mechanical fixturing. VPC modules can be intermixed to establish flexible custom interfaces which are ideal for functional and system testing applications. The 9025TR uses all standard VPC 90 series modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit. Slide kit required, but not included.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Female, 2m
A025CFR-025CFR-5A200
This 2m long female to female 25-Pin Micro-D Cable Assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products.
-
product
Advanced Power System: Dynamic DC Power Supply, 80 V, 25 A, 2000 W
N7974A
The N7974A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
Oscilloscope 25 GHz, 4 Channels
UXR0254B
UXR0254B Infiniium UXR-Series is the 25 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope.
-
product
ITA, 9025, 25 Module, Single Tier, for EMI
410104306
ITA, 9025, 25 Module, Single Tier, for EMI
-
product
25 Pin 1.27mm Pitch Micro-D Cables - 25 Pin Connector to Unterminated
The connector to unterminated cable assemblies below are suitable for high-density applications including Pickering’s LXI DIO/Trigger port.
-
product
Advanced Power System - Dynamic DC Power Supply, 40 V, 25 A, 1000 W
N7952A
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
Module Accessory Kit, Quantity 26, 4-40 x .25" Flat Head Phillips Screws
510109361
Module Accessory Kit, Quantity 26, 4-40 x .25" Flat Head Phillips Screws.
-
product
Adapter Plate, Allows 10 Module ITA To Accept 25 Module Enclosure
410112424
The Adapter Plate allows the user to use standard 25 module enclosures with the 10 module ITA. See enclosures in the 25 Module section for more options.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-02
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.