-
product
Cable Test Van
ETL-35
ETL-35 is a cable test van designed for testing electrical substation equipment.Apart from cable insulation withstand testing with DC (rectified) voltage up to 60 kV and ability to measure very small leakage currents, the system can be used for testing various objects with small electrical capacitance with AC voltage of up to 100 kV and measuring dielectric dissipation factor (Tan Delta) at industrial frequency.
-
product
Compact Cable Test Van
ETL-8
Van-based cable test and fault location system ETL-8 is used for testing cable insulation and locating cable faults using a variety of methods.
-
product
Cable Test Van
BAUR Transcable 4000/A 80-3
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/A 80-3. The transcable 4000/A 80-3 cable test van is equipped with an automatic control system. The high voltage switch unit is enclosed and is actuated electrically with the fully automatic KE 3 control unit.
-
product
Cable Test Van
BAUR Transcable 4000/S 32-3
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 32-3. Thetranscable 4000/S 32-3 cable test van is a 32 kV cable fault location system in 3-phase version. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is maintenance-free and fully safe to touch.
-
product
Cable Test Box
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
product
Cable Test Van
Techno Instrumentation (India) Private Limited
Cable fault locating van with installation according to users specifications and requirement.
-
product
Cable Continuity Test Fixture
CCT
6 and 8 Wire Cable Continuity Test Fixtures For convienient desk top and bench top The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
product
Cable Test Van
ETL-10M
ETL-10M is a cable test van with three-phase connection designed for testing cable insulation with DC (rectified) voltage up to 60 kV and testing other electrical objects with up to 50 kV AC voltage of industrial frequency.
-
product
Microwave/RF Cable Test Assemblies, 110 GHz
Gore offers a rugged, lightweight 110 GHz test assembly that optimizes the performance of test systems while reducing the total cost of test and ownership over time. Our assemblies provide reliable electrical performance with flexure and temperature in demanding environments.
-
product
Cable Harness Test System
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
product
Cable-End Test Fixtures
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
product
Cable Test Van
BAUR Transcable 4000/S 110-1
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 110-1. The transcable 4000/S 110-1 cable test van is a 110 kV cable fault location system in single-phase version. The system is actuated with the semi-automatic MGS control unit. The high voltage switch unit is single-phase, up to 32 kV, the 110 kV switching level is designed as air-insulated ceiling switch.
-
product
Cable Test and Diagnostics
Cable testing and diagnostics provides information about the cable’s global condition (e.g. the cable’s overall insulation system), and will reveal localised problems, such as poor joints and terminations; it will also reveal localised weak spots in the insulation. Various cable tests are carried out to spot potential failures before they can cause severe outages. Megger cable test equipment provides access to all of the technology needed to make informed cable management decisions through the different stages of the cable’s life cycle.
-
product
Overhead Line & Cable Impedance Test Sets
T&R Test Equipment Overhead Line & Cable Impedance Test Sets
-
product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
product
Cable Test Instruments
Do you have systems that include a large number of coaxial devices? Our best-selling ATE product line includes a cable test instrument that automates the task of precision testing of coaxial devices. These series of cable test instruments include both a scalar and a vector model. They offer fast precision measurements in a rugged and small portable package. Programming options allow instant test set-up and measurement recall from a potential database of thousands of test devices. Using a user interface that includes clear instructions with picture prompts, anyone can successfully make precision microwave measurements with a simple click of a button.
-
product
Cable Test Van
ETL-35K
ETL-35K system has a multitude of applications in electrical equipment testing and maintenance: testing cable insulation with DC (rectified) voltage up to 60 kV, measuring small leakage current of surge arrestors, high-voltage testing with AC voltage up to 100 kV at industrial frequency, underground utilities tracing, cable fault pre-location and pinpointing, and measuring capacitance and tan delta of various electrical objects at industrial frequency.
-
product
Cable Fault, Test And Diagnostics
Allows an operator to test twisted pair cables for faults without physically disconnecting the cables from the switch.
-
product
Cable Test Van
Titron
BAUR Prüf- und Messtechnik GmbH
Automatic cable test van. The BAUR titron is a new automatic cable test van designed for cable fault location and cable testing. The new generation of the high-performance cable test van is based on state-of-the-art technology and provides effi cient, safe and reliable cable fault location and cable testing.* New intuitive operational concept* Central, automatic system control* Top reliability and quality standard* Flexible in terms of technology and equipment
-
product
Microwave/RF Cable Test Assemblies / General Purpose
For test applications that require consistent and highly repeatable measurements, GORE® Microwave/RF Assemblies for general purpose test applications provide reliable electrical performance with proven phase and amplitude stability. The smaller diameter and highly flexible, yet durable construction simplify the routing process while ensuring long-lasting electrical performance after installation, particularly in board-to-board and inside-the-box systems.
-
product
Mobil Cable Test and Fault Location System
SWG-12 (SWG-32)
• testing cable insulation with DC (rectified) voltage up to 32 kV;• conditioning faults by burning faulty cable insulation with current up to 100 mA;• pre-locating cable faults with the reflectometer RIF-9 based on the pulse reflection method (TDR), voltage wave oscillation method (DECAY), impulse current envelope (ICE) method and arc reflection method (ARC / ARC multi-shot);• pinpointing cable faults with the acoustic method with up to 2000 J surge wave generator and a suitable signal receiver.
-
product
Microwave/RF Cable Test Assemblies
PHASEFLEX
For test applications that require precise, repeatable measurements, microwave/RF test assemblies from Gore provide excellent phase and amplitude stability with flexure. Our rugged, lightweight assemblies deliver reliable performance with longer service life and reduced equipment downtime resulting in lower costs for testing in laboratory, production and field test environments.
-
product
Cable Modem Test Platform Version 2
Promptlink Communications, Inc.
CMTPv2 has broad support for all DOCSIS environments and even offers support for new higher-speed DOCSIS 3.1 devices. It continues support for all equipment vendors, impartially treating each vendor's devices with maximum performance and minimum hassle.
-
product
High Voltage Cable/Harness Test System
CKT1175-50
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
product
Cable Test Van
BAUR Transcable 4000/S 70-3
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 70-3. The transcable 4000 70 kV 3/S cable test van varies in comparison with the transcable 32 kV - 3S in the 70 kV voltage level. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is 3-phase, air and solid matter insulated and safe to touch.
-
product
High Voltage DC Cable Test Systems
We can offer from ±18kVdc to ±30kVdc units which all have automatic earthing for discharging capacitive loads. They are designed to perform tests on installed cables and jointing systems.
-
product
Cable Modem Test Platform
Promptlink Communications, Inc.
CMTP has broad support for the mixed environment of DOCSIS 3.0, and earlier devices. Similarly, it supports all DOCSIS/Euro DOCSIS equipment vendors, impartially treating each vendor's devices with maximum performance and minimum hassle.CMTP is fully automated, requiring no user input for testing.CMTP tests the basic Cable Modem, Wi-Fi and EMTA parameters such as signal levels, signal to noise ratio, etc. as well as device throughput and packet loss. For PacketCable devices, CMTP tests each phone port individually, with maximum functionality being tested.CMTP can also be configured to upgrade the firmware of the devices in a multi-step and conditional process.
-
product
Cable Test Vans and Systems
BAUR Prüf- und Messtechnik GmbH
Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.
-
product
VNA Microwave/RF Cable Test Assemblies
VNA Microwave/RF Test Assemblies set the industry standard for vector network analyzers (VNAs) through 70 GHz. Constant and/or highly repetitive movement of cables can compromise the measurement precision of high-performance VNAs. Leading manufacturers choose GORE® VNA Microwave/RF Test Assemblies because of the improved performance they see in their equipment.
-
product
Cable/Harness Test System with Rack-Mounted Switching
CKT1175-20
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
